ACTIVESHOP Azzurro 891 Electric Cosmetic Chair

Importer Information

Importer: Z O.O.

Address: Ul. Graniczna 8b, bud. DC2A, 54-610 Wrocław, Poland

Website: www.activeshop.com.pl

Revision: A/06/2024

Before Use

1. Ensure all packaging materials have been removed.
2. Verify the chair is in working condition.
3. Position the cosmetic chair in its intended operational area.
4. Connect the power plug to a suitable electrical outlet.

Important Note: This appliance is not intended for use by children or inexperienced individuals. Children must be supervised and must not play near the cosmetic chair.

Dimensions

The ACTIVESHOP Azzurro 891 electric cosmetic chair has the following approximate dimensions:

• Overall Length: 100 cm
• Overall Width: 58 cm
• Seat Width: 53 cm
• Seat Depth: 62 cm
• Backrest Height: 80 cm
• Armrest Width: 10 cm
• Armrest Height from Seat: 7 cm
• Footrest Width: 58 cm
• Footrest Length: 62 cm
• Footrest Extension Range: 0-15 cm
• Adjustable Seat Height Range: 61 cm (min) to 92 cm (max)

Operation and Remote Control

The appliance is operated using a remote control. The remote control features the following functions:

• [Memory Preset 1]: Save current settings.
• [Memory Preset 2]: Save current settings.
• [Seat Height Up/Down]: Adjusts the seat height within the range of 61-92 cm. Press to raise or lower the seat.
• [Backrest Angle Adjustment]: Adjusts the angle of the backrest.
• [Footrest Position Adjustment]: Changes the position of the footrest.

Footrest Adjustment Details

The footrest can be adjusted and extended by 0-15 cm. To extend the footrest, turn the knob located on the underside and pull the footrest to the desired length.

Cleaning and Disinfection

Before cleaning, always disconnect the appliance from the electrical mains.

Regular cleaning is essential to maintain the chair's surface in good condition. It is recommended to clean and disinfect the chair after each use. A thorough disinfection should be performed monthly.

Cleaning Specific Surfaces:

Metal and Plastic Surfaces

Wipe metal and plastic surfaces, including control elements, with a damp cloth. For hard-to-reach areas or corners, a small brush can be effective. Avoid using excessive liquid on the appliance. After cleaning, disinfect the appliance with an appropriate disinfectant liquid.

Stainless Steel Surfaces

For best results, use a mild cleaning agent. Ammonia-based solutions can be used for removing stubborn stains. Most solvents are suitable, but avoid chlorine-based solutions.

Lacquered or Chrome-Plated Metal Surfaces

• Do not use water jets (e.g., showers, high-pressure washers) for cleaning.
• Avoid cleaning at high temperatures or high humidity. Do not expose the appliance to conditions that could lead to liquid contamination.
• Do not use solvents or acids for cleaning these surfaces.

Seat Surface

Wipe the seat surface evenly with a specialized leather cleaning agent, followed by wiping with a clean, soft cloth.

Maintenance

Disconnect the appliance from the electrical mains before performing any maintenance.

1. Repairs must be carried out by experienced and manufacturer-authorized personnel. Unauthorized repairs may lead to injury or damage to the appliance, for which the manufacturer disclaims responsibility.
2. Use only original spare parts approved by the manufacturer.
3. Do not operate the electric cosmetic chair or its accessories if they are not functioning correctly.
4. All maintenance and repair activities must be documented.

Maintenance Checks (Weekly/Bi-annual)

Perform the following checks:

• Weekly: Check the control elements and their connections.
• Every Six Months: Check the condition and functionality of:
  1. Power cable and its fastening.
  2. Motor connection.
  3. Control box and its connections.
  4. Accessory connections.
  5. Normal operation of the locking system.

If any faults are detected, cease using the appliance and contact an authorized service center. The drive/control unit may only be opened or replaced by experienced or authorized personnel. If any part of the appliance is damaged, disconnect the power cable, stop using it, and notify the service department.

Troubleshooting