Primo Deluxe Bottom-Loading Water Dispenser with Self-Sanitization
Model: B263 / #601090SO
Features
Water Dispensing Controls:
- Dark Blue: Cold
- Light Blue: Cool
- Red: Hot
Function Lights:
- Green light above ON icon: Dispenser is plugged in. Flashes when self-sanitization is operating.
- Green light above snowflake icon: Dispenser is cooling water.
- Green light above wavy lines icon: Dispenser is heating water.
- Blinking red light above bottle icon: Bottle is empty.
Spout: Water is dispensed here.
Self-Sanitization: Sanitizes water reservoirs and lines.
LED Nightlight: Assists in low light situations.
Drip Tray with Full Indicator: Removable and dishwasher-safe. Red indicator rises when it's time to empty.
Probe Assembly: Pumps water from the bottle into the hot and cold reservoirs.
Probe Hanger: Holds the probe assembly inside the cabinet door to keep it clean during bottle replacement.
Bottom Loading Design: Bottles fit inside the bottom of the cabinet for easy use.
Quick Start Guide
- Place the dispenser on a level floor surface indoors. Do not plug in the power cord until instructed.
- Position the dispenser with at least 4 inches of clearance from the wall and 4 inches on both sides.
- Slide the drip tray into place.
- Clean the probe with a damp cloth and dish soap. Visit PrimoWater.com for detailed cleaning instructions. Place the probe assembly on the hanger inside the door.
- Remove the cap from a Primo® water bottle (sold separately). Insert the probe assembly into the bottle, pressing firmly to secure. For 3-gallon bottles, separate the probe cap from the collar and press the collar securely over the bottle opening.
- Slide the bottle into the cabinet and close the door. Water will not pump unless the door is fully closed.
- Plug the dispenser into a GFCI outlet. The dispenser will begin pumping water to fill internal reservoirs.
- Turn on desired functions by flipping switches on the back of the dispenser to the ON position (Green for chilling, Red for heating, Blue for night light, Black for self-sanitization - press and hold for 3 seconds).
- After the dispenser stops filling, dispense and discard at least 1 quart (approx. 2 pint glasses) of water from the cold, cool, and hot spouts.
- Water will be ready to dispense fully chilled in approximately 1 hour or piping hot in approximately 12 minutes.
- Register your dispenser at PrimoWater.com to activate your 1-year warranty.
Operating Instructions
Dispensing Cold Water
- Water will be fully chilled in approximately 1 hour. The cooling light will turn off when complete.
- Press and hold the blue cold water button to dispense. Release to stop.
Dispensing Cool Water
- Press and hold the light blue cool water button to dispense. Release to stop.
Dispensing Hot Water
- Water will be heated in approximately 12 minutes. The heating light will turn off when complete.
- Slide the child lock back, then press and hold the red hot water button to dispense. Release to stop.
Caution: This unit dispenses hot water that can cause severe burns. Avoid direct contact. Keep children and pets away. Never allow children to dispense hot water without supervision. Disable heating by switching the heating convenience switch to OFF or unplugging the unit. Use only for water.
Replacing the Bottle
The empty bottle light will flash when the bottle is empty. The dispenser will not heat or cool water when this light is flashing. Replace the bottle promptly.
- Open the cabinet door and slide out the empty bottle.
- Remove the probe assembly from the empty bottle and place it on the probe hanger.
- Set the empty bottle aside.
- Remove the plastic cap from the new bottle.
- Insert the probe into the new bottle, pressing firmly until it clicks. Ensure the tube touches the bottom. For 3-gallon bottles, adjust the probe assembly as described in the Quick Start Guide.
- Slide the new bottle into the cabinet and close the door.
Cleaning & Maintenance
Clean the cabinet, controls, bottle probe, and spout each time you replace the water bottle for best taste, performance, and hygiene. Use a clean, soft cloth with a food-grade sanitizer or bleach.
Empty and clean the drip tray as needed. Visit PrimoWater.com for detailed cleaning instructions.
Run a self-sanitization cycle regularly to sanitize water reservoirs and lines. To initiate, press and hold the black switch on the back of the dispenser for 3 seconds. The cycle takes 90 minutes. Avoid dispensing water during this cycle as the ozone may cause a slight odor, which will dissipate shortly after completion.
Limited Warranty
Primo Water Corporation warrants this dispenser to the original purchaser for one (1) year from the date of purchase against defects in material and workmanship, provided it is operated according to the instructions. Proof of purchase is required. The warranty covers repair or replacement of defective parts under normal use. Contact Primo Water Customer Service for assistance before returning any parts. Transportation charges for returned parts must be prepaid by the customer; replacement parts will be shipped freight prepaid.
The Limited Warranty does not cover failures due to accident, abuse, misuse, alteration, improper installation, or lack of normal maintenance. Damage to the finish (scratches, dents, discoloration, rust) is also not covered.
This warranty is in lieu of all other express warranties. Primo disclaims all warranties for products purchased from unauthorized sellers. After the one-year period, Primo disclaims all implied warranties, including merchantability and fitness for a particular purpose. Primo shall not be liable for any special, indirect, punitive, incidental, or consequential damages.
For warranty information, additional assistance, or instructional videos, visit PrimoWater.com or call 1-866-429-7566. Primo Water Corporation, 101 N. Cherry St. Suite 501, Winston-Salem, NC 27101.
Spanish Operating Instructions
PARA DISPENSAR AGUA FRÍA
- El agua tardará aproximadamente 1 hora en enfriarse completamente. La luz de enfriamiento se apagará cuando el agua esté totalmente fría.
- Presione y mantenga presionado el botón azul de agua fría para dispensar. Suelte para detener.
PARA DISPENSAR AGUA FRESCA
- Presione y mantenga presionado el botón azul claro de agua fresca para dispensar. Suelte para detener.
PARA DISPENSAR AGUA CALIENTE
- El agua tardará aproximadamente 12 minutos en calentarse. La luz de calentamiento se apagará cuando el agua esté caliente.
- Deslice el seguro para niños hacia atrás, luego presione y mantenga presionado el botón rojo de agua caliente para dispensar. Suelte para detener.
Precaución: Esta unidad dispensa agua caliente que puede causar quemaduras graves. Evite el contacto directo. Mantenga a los niños y mascotas alejados. Nunca permita que los niños dispensen agua caliente sin supervisión. Desactive la función de calentamiento o desenchufe la unidad. Use solo para agua.
PARA REEMPLAZAR EL BOTELLÓN
La luz de botellón vacío parpadeará cuando el botellón esté vacío. El dispensador no calentará ni enfriará agua con esta luz parpadeando. Reemplace el botellón lo antes posible.
- Abra la puerta del gabinete y deslice el botellón vacío hacia afuera.
- Retire el conjunto del tubo surtidor del botellón vacío y colóquelo en el colgador.
- Deje a un lado el botellón vacío.
- Retire la tapa de plástico del nuevo botellón.
- Inserte el tubo surtidor en el nuevo botellón, presionando firmemente hasta que haga clic. Asegúrese de que el tubo toque el fondo. Para botellones de 3 galones, ajuste el conjunto del tubo surtidor como se describe en la Guía de Inicio Rápido.
- Deslice el nuevo botellón dentro del gabinete y cierre la puerta.
LIMPIEZA Y MANTENIMIENTO
Limpie el gabinete, los controles, el tubo surtidor y la boquilla cada vez que reemplace el botellón de agua para obtener el mejor sabor, rendimiento e higiene. Use un paño suave y limpio con un sanitizante de grado alimentario o lejía.
Vacíe y limpie la bandeja de goteo según sea necesario. Visite PrimoWater.com para obtener instrucciones detalladas de limpieza.
Ejecute un ciclo de autolimpieza regularmente para desinfectar los tanques y las líneas de agua. Para iniciar, mantenga presionado el interruptor negro en la parte posterior del dispensador durante 3 segundos. El ciclo dura 90 minutos. Evite dispensar agua durante este ciclo, ya que el ozono puede causar un ligero olor, que se disipará poco después de su finalización.
