Primo Deluxe Bottom-Loading Water Dispenser

Features

• WATER DISPENSING CONTROLS: Dark Blue - Cold ?❄️, Light Blue - Cool ?, Red - Hot ?
• FUNCTION LIGHTS:
  • Green light below ON icon (?): Dispenser is plugged in.
  • Green light below snowflake (?❄️): Dispenser is cooling water.
  • Green light below wavy lines (?〰️): Dispenser is heating water.
  • Blinking red light below bottle icon (?): Bottle is empty.
• SPOUT: Water is dispensed here.
• LED NIGHTLIGHT: Helps in low light situations. ?
• DRIP TRAY WITH FULL INDICATOR: Removable and dishwasher-safe. Red indicator rises when it's time to empty.
• PROBE ASSEMBLY: Probe pumps water from the bottle into the hot and cold reservoirs.
• PROBE HANGER: Rest probe assembly on the hanger (located inside the cabinet door) to keep it clean while replacing bottles.
• BOTTOM LOADING DESIGN: Bottles fit inside the bottom of the cabinet for easy use.
• WATER BOTTLE: Not included. Uses 3 and 5-gallon bottles. Visit PrimoWater.com to find Primo® water at the store nearest you.

Quick Start Guide

Follow these steps to set up your dispenser:

1. Place the dispenser on a level floor surface in the desired location in your home. Product is intended for indoor use only. [Note: Do NOT plug power cord into wall outlet until instructed.]
2. Position dispenser so the back is at least 4 inches from the wall and there are at least 4 inches of clearance on both sides.
3. Slide drip tray into place.
4. Clean probe with a damp cloth and dish soap. (Visit PrimoWater.com for detailed cleaning instructions.) Place probe assembly on hanger inside door to keep it clean.
5. Grab a bottle of Primo® water (sold separately) and fully remove the cap. Insert probe assembly into bottle. Press firmly to secure assembly over bottle opening. For 3-gallon bottles, squeeze the tabs on the top of the probe assembly to separate the probe cap from the collar and press the collar securely over the bottle opening.
6. Slide bottle inside the cabinet and close cabinet door. [Note: Water will not pump from bottle unless door is fully closed.]
7. Plug dispenser into a ground fault circuit interrupting (GFCI) outlet. You will hear the dispenser begin to pump water to fill the internal hot and cold reservoirs.
8. Turn on desired functions by flipping the switches on the back of the dispenser to the ON position. (Green ? chills water, Red ? heats water, Blue ? night light)
9. Once the dispenser has stopped filling the internal reservoirs, dispense and dispose at least 1 quart (approximately 2 pint glasses) of water from the cold, cool, and hot spouts.
10. Your water will be ready to dispense fully chilled in approximately 1 hour or piping hot in approximately 12 minutes.
11. Register your dispenser at PrimoWater.com to activate your warranty, which runs for 1 year from date of purchase.

Water Bottle Information: Primo® Pre-Filled Exchange Water or Self-Service Refill Water from Primo® & Glacier® (sold separately). Available at thousands of locations nationwide. Learn more at PrimoWater.com/locations.

Operating Instructions

Dispensing Cold Water

• Water will take approximately 1 hour after initial set up to become completely chilled. Cooling light (?❄️) will turn off once the water has been fully chilled.
• Press and hold the blue cold water button (?❄️) to dispense cold water. Release to stop dispensing.

Dispensing Cool Water

• Press and hold the light blue cool water button (?) to dispense cool water. Release to stop dispensing.

Dispensing Hot Water

• Water will take approximately 12 minutes after initial set up to reach its hottest temperature. Heating light (?〰️) will turn off once the water has been fully heated.
• Slide the red child lock back, then press and hold the hot water button (?) to dispense hot water. Release to stop dispensing.

CAUTION:

This unit dispenses water at temperatures that can cause severe burns. Avoid direct contact with hot water. Keep children and pets away from the unit while dispensing. Never allow children to dispense hot water without proper and direct supervision. Disable the heating feature by switching the heating convenience switch on the back of the unit to the OFF position or unplug the unit. Product is intended for water dispensing only. Do not use with other liquids.

Replacing the Bottle

When your bottle is empty, the empty bottle light (?) will flash. To prevent freeze-up or over-heating, the dispenser will not heat or cool water when the bottle light is flashing. Replace the bottle as soon as possible to re-enable cooling and heating.

1. Open dispenser cabinet door and slide empty bottle out of cabinet.
2. Remove probe assembly from the empty bottle and place it on the probe hanger.
3. Set empty bottle aside.
4. Remove the entire plastic cap from the new bottle.
5. Place probe into the new bottle and slide the collar down until it clicks into place. Press on the top of the probe until the tube touches the bottom of the bottle. For 3-gallon bottles, squeeze the tabs on the top of the probe assembly to separate the probe cap from the collar and press the collar securely over the bottle opening.
6. Slide the bottle into the cabinet and close the door.

Cleaning & Maintenance

For best taste, performance, and hygiene, clean your cabinet, controls, bottle probe, and spouts each time you replace your water bottle. Use a clean, soft cloth and food grade sanitizer or bleach.

Empty and clean drip tray as needed. Clean the cold reservoir at least once every 3 months. Visit PrimoWater.com for detailed cleaning instructions.

Limited Warranty

Primo Water Corporation ("Vendor") warrants to the original purchaser of this dispenser, and to no other person, that if this dispenser is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in such dispenser shall be free from defects in material and workmanship. Vendor may require reasonable proof of your date of purchase from an authorized retailer or distributor. Therefore, you should retain your sales slip or invoice. The Limited Warranty shall be limited to repair or replacement of parts which prove defective under normal use and service and which Vendor shall determine in its reasonable discretion upon examination to be defective. Before returning any parts, you should contact Vendor’s Customer Service Department using the contact information listed below. If Vendor confirms, after examination, a defect covered by this Limited Warranty in any returned part, and if Vendor approves claim, Vendor will replace such defective part without charge. If you return defective parts, transportation charges must be prepaid by you. Vendor will return replacement parts to original purchaser, freight or postage prepaid. For units purchased outside of the continental US (limited to Hawaii, Alaska, and Puerto Rico), dispensers determined to be defective by the Vendor should be returned or exchanged at the original point of purchase within the warranty period.

The Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance or service by you or any third party, or failure to perform normal and routine maintenance on the dispenser, as set out in the User’s Manual. In addition, the Limited Warranty does not cover damage to the finish after purchase, including without limitation scratches, dents, discoloration or rust.

The Limited Warranty is in lieu of all other express warranties. Vendor disclaims all warranties for products that are purchased from sellers other than authorized retailers or distributors. AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS WARRANTY, VENDOR DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FURTHER, VENDOR SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Vendor assumes no responsibility for any defects caused by third parties. This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she lives. Some jurisdictions do not allow exclusions or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to you.

Support & Contact Information

For warranty information, additional assistance, or instructional videos for maintaining or operating your dispenser, visit our customer support page at PrimoWater.com or call us at 1-866-429-7566. Our US-based customer service team would be happy to help! ?️

Primo Water Corporation, 101 N. Cherry St. Suite 501, Winston-Salem, NC 27101

© 2018 Primo Water Corporation