Primo Professional Series Bottom Loading Water Dispenser

Model #: 601125

Important: Do not return dispenser to store. For questions or issues, contact 1-866-429-7566.

Save this manual for future use.

[UL Certified]

Features & Functions

Brewer Zone: Area for drip or single-serve coffee makers, with Primo-Mount pad and magnet to prevent sliding and tipping.
Cold Control: Touch to dispense water; release to stop.
Cooling Indicator: Blue light around the cold control indicates water is cooling. Wait for light to turn off for coldest output.
Empty Bottle Indicator: Orange blinking light and bottle icon signal an empty bottle.
Bottle Support: Aids in aligning bottles and glasses with the spout to prevent spills.
Spout: Dispenses water; silver plating helps kill bacteria.
LED Nightlight: Located behind the bottle support for low-light situations.
Probe Assembly: Connects to the water bottle inside the cabinet to pump water to the cold tank.
Probe Hanger: Located inside the door at the top to keep the probe assembly clean when changing bottles.
Drip Tray & Grid: Dishwasher safe, slides out. Features a red indicator that rises when the tray is full.
Water Bottle: Not included; requires 3, 4, or 5-gallon bottles. Visit www.PrimoWater.com for availability.
Convenience Switches (Rear Panel): Nightlight Switch: Blue switch on the far left to turn the nightlight ON or OFF. Cold Control Switch: Green switch to turn cooling ON or OFF.

Warnings & Safety Precautions

Read this entire guide before assembling, installing, and operating the dispenser to reduce the risk of injury and property damage.

Failure to follow instructions can cause personal injury or property damage.

Always exercise basic safety precautions.
Ensure the dispenser is properly assembled and installed according to this manual before use.
Intended for water dispensing only. Do not use other liquids or for other purposes. Use only known, microbiologically safe bottled water.
For indoor use only. Keep in a dry place away from direct sunlight. Do not use outdoors.
Install and use only on a hard, flat, and level surface.
Do not place the dispenser in an enclosed space or cabinet.
Do not operate in the presence of explosive fumes.
Position the back of the dispenser at least 4 inches from the wall, with at least 4 inches clearance on the sides for free airflow.
The dispenser is intended for a ground fault interrupting receptacle.
Do not use an extension cord.
Always grasp the plug and pull straight out from the outlet; never pull the power cord.
Do not use if the cord is frayed or damaged.
Do not immerse the cord, plug, or any part of the dispenser in water or other liquids to prevent electric shock.
Ensure the dispenser is unplugged before cleaning.
Never allow children to dispense water without proper, direct supervision. Unplug the unit to prevent unsupervised use by children.
Do not dispense water if the bottle is empty.
Service should only be performed by a certified technician. Contact 866-429-7566 for assistance.

Limited Warranty

Primo Water Corporation warrants this dispenser to the original purchaser for two (2) years from the date of purchase against defects in material and workmanship, provided it is assembled and operated according to the instructions.

Proof of purchase (sales slip or invoice) is required.

The warranty covers repair or replacement of defective parts under normal use and service. Contact Primo Water's Customer Service Department for claims. Return transportation charges for defective parts must be prepaid by the customer. Replacement parts will be shipped freight prepaid.

For units purchased outside the continental US, defective dispensers must be returned or exchanged at the original point of purchase within the warranty period.

Exclusions: The warranty does not cover failures due to accident, abuse, misuse, alteration, misapplication, improper installation, improper maintenance or service, or failure to perform normal maintenance. It also does not cover cosmetic damage like scratches, dents, discoloration, or rust after purchase.

This warranty is in lieu of all other express warranties. Primo disclaims warranties for products purchased from unauthorized sellers. After one year, Primo disclaims implied warranties of merchantability and fitness for a particular purpose.

Primo shall not be liable for any special, indirect, punitive, incidental, or consequential damages. Primo assumes no responsibility for defects caused by third parties.

This warranty provides specific legal rights; rights may vary by jurisdiction.

Primo Water Corporation
101 N. Cheery St, Suite 501
Winston-Salem, NC 27101
866-429-7566

Set Up

No tools or hardware required.

Locate Dispenser

Notice: Do NOT plug the power cord into the wall outlet until instructed.

Place dispenser upright.
Locate dispenser on a hard, level surface in a cool, shaded location near a ground fault interrupting receptacle.
Position the dispenser so the back is at least 4 inches from the wall, with at least 4 inches of clearance on both sides for airflow.

Install Drip Tray & Grid

Remove the drip tray and grid from protective packaging.
Slide the drip tray assembly onto the door.

Install Water Bottle

Bottle not included. Requires standard 3, 4, or 5-gallon water dispenser bottles. Visit www.PrimoWater.com to find Primo Water at a store near you.

Visual Description: Diagram shows a water bottle with a probe assembly, consisting of a head and collar. Instructions detail cleaning the bottle cap and neck, opening the dispenser door, placing the probe assembly on the hanger, removing the bottle cap, cleaning the new bottle, inserting the probe into the bottle, sliding the collar down to click, and pushing the head down until the tube reaches the bottom of the bottle. Finally, slide the bottle into the cabinet and close the door.

Provide Electricity

Plug the power cord into a ground fault interrupting receptacle. The pump will begin moving water from the bottle to the hot and cold tanks. It may take up to 4 minutes to fill the tanks initially, during which the pump will run continuously. This is normal.

Operation

The dispenser has been tested and sanitized. Dispense and dispose of at least one quart of water before drinking to remove any dust or odors accumulated during transit.

Dispensing Cold Water (37°-50°F / 3°-10°C)

Tank Capacity: 3.6L, Flow Rate: 35mL per second / 126L per hour.

It takes approximately 1 hour after setup for the water to reach maximum cold temperature. The compressor will run continuously during this time, which is normal.

Position a bottle, glass, pitcher, or cooking pot below the spout.
Touch the center of the cold water control to start water flow.
Release the control once the desired fill level is achieved.

Changing Bottles

A flashing red light indicates the bottle is empty. Replace the bottle as soon as possible.

Open the dispenser door and slide the empty bottle out.
Remove the probe assembly from the empty bottle and place it on the probe hanger.
Set the empty bottle aside.
Place a fresh bottle outside the cabinet. Remove the entire plastic cap from the top of the bottle. Clean the outside of the new bottle with a cloth.
Place the probe into the bottle. Slide the collar down until it clicks. Push the head down until the tube reaches the bottom of the bottle.
Slide the bottle into the cabinet and close the door.

Maintenance

For best taste, performance, and hygiene:

Clean the cabinet, controls, bottle probe, and spout each time you change the water bottle. Use a clean soft cloth and a food-grade sanitizer or bleach.
Empty and clean the drip tray, grid, and float as needed.
Use only high-quality Primo purified bottled water to minimize mineral deposits that can clog lines and affect taste.

For additional instructions and videos, visit www.primowater.com/support.

Troubleshooting

Cold water is not cold

It takes up to one hour after setup for cold water to dispense.
Ensure the power cord is properly connected to a working outlet.
Verify the dispenser's back is at least 4 inches from a wall and there is free airflow on all sides.
Confirm the green cold control switch on the back panel is ON.
If water is still not cold, call 866-429-7566 for assistance.

Nightlight Isn't Working

Ensure the power cord is properly connected to a working outlet.
Confirm the nightlight switch on the back panel is ON.

Please visit www.PrimoWater.com for more useful information, instructional videos, tips, and special offers.

	Primo Deluxe Bottom-Loading Water Dispenser - Features, Operation, and Warranty Comprehensive guide to the Primo Deluxe Bottom-Loading Water Dispenser, covering features, quick start, operating instructions, cleaning, maintenance, and limited warranty information. Model B250.
	Primo 601000 Bottom Loading Water Dispenser User Manual and Guide Comprehensive guide for the Primo 601000 Bottom Loading Water Dispenser, covering features, installation, operation, safety precautions, troubleshooting, and limited warranty. Learn how to set up and use your water dispenser.
	Primo 601090 C Bottom Loading Water Dispenser with Self-Cleaning: User Manual and Guide Comprehensive guide for the Primo 601090 C bottom loading water dispenser. Learn about setup, operation, maintenance, troubleshooting, and warranty information for your self-cleaning water cooler.
	Primo Home Series Spill Proof Water Dispenser User Manual This user manual provides comprehensive instructions for the Primo Home Series Spill Proof Water Dispenser, covering setup, operation, maintenance, safety warnings, and troubleshooting. Learn how to install and use your water dispenser safely.
	Primo Smart Touch Water Dispenser B275 \| User Guide & Warranty Comprehensive guide for the Primo Smart Touch Water Dispenser (Model B275). Learn about features, quick setup, safety precautions, and the 1-year limited warranty. Dispenses hot, cold, and cool water.
	Primo Home Series Bottom Loading Water Dispenser User Manual and Guide Comprehensive user manual for the Primo Home Series Bottom Loading Water Dispenser, covering features, safety, setup, operation, maintenance, and troubleshooting.
	Primo hTrio Water Dispenser: Quick Start and Operating Guide Get started quickly with the Primo hTrio Multi-Purpose Beverage Dispenser. This guide covers setup, dispensing cold and hot water, preparing single-serve beverages, using the reusable filter, bottle replacement, cleaning, and key features. Includes limited warranty information.
	Primo Bottom Loading Water Dispenser with Self-Cleaning User Manual User manual for the Primo Bottom Loading Water Dispenser with Self-Cleaning (Model # 601118). Provides detailed instructions on setup, operation, maintenance, troubleshooting, and limited warranty information.