Primo Deluxe Bottom-Loading Water Dispenser

Features

• Water Dispensing Controls:
  • Dark Blue: Cold Water
  • Light Blue: Cool Water
  • Red: Hot Water
• Indicator Lights:
  • Green ON icon: Dispenser is plugged in.
  • Green snowflake: Dispenser is cooling water.
  • Green wavy lines: Dispenser is heating water.
  • Blinking red bottle icon: Bottle is empty.
• Spouts: Right dispenses cold water, left dispenses hot water, and center dispenses cool water.
• LED Nightlight: Aids visibility in low light.
• Drip Tray with Full Indicator: Removable and dishwasher-safe. A red indicator rises when it's time to empty.
• Probe Assembly: Pumps water from the bottle into the hot and cold reservoirs.
• Probe Hanger: Stores the probe assembly inside the cabinet door to keep it clean during bottle changes.
• Bottom Loading Design: Bottles fit inside the cabinet for convenient use.
• Water Bottle: Sold separately. Uses 11.3 and 18.9-liter bottles. Visit PrimoWater.ca to find Primo® water at the store nearest you.

Quick Start Guide

1. Place the dispenser on a level floor surface in the desired location in your home. Product is intended for indoor use only. [Note: Do NOT plug power cord into wall outlet until instructed.]
2. Position dispenser so the back is at least 4 inches from the wall and there are at least 4 inches of clearance on both sides.
3. Slide drip tray into place.
4. Clean probe with a damp cloth and dish soap. Place probe assembly on hanger inside door to keep it clean.
5. Grab a bottle of Primo® water (sold separately) and fully remove the cap. Insert probe assembly into bottle. Press firmly to secure assembly over bottle opening. For 11.3-liter bottles, squeeze the tabs on the top of the probe assembly to separate the probe cap from the collar and press the collar securely over the bottle opening.
6. Slide bottle inside the cabinet and close cabinet door. [Note: Water will not pump from bottle unless door is fully closed.]
7. Plug dispenser into a ground fault circuit interrupting (GFCI) outlet. You will hear the dispenser begin to pump water to fill the internal hot and cold reservoirs.
8. Turn on desired functions by flipping the switches on the back of the dispenser to the ON position. [Switches: Green for cooling, Red for heating, Blue for night light]
9. Once the dispenser has stopped filling the internal reservoirs, dispense and dispose at least 1 quart (approximately 2 pint glasses) of water from the cold, cool, and hot spouts.
10. Your water will be ready to dispense fully chilled in approximately 1 hour or piping-hot in approximately 12 minutes.
11. Register your dispenser at PrimoWater.ca to activate your warranty, which runs for 1 year from date of purchase.

Operating Instructions

Dispensing Cold Water

1. Water will take approximately 1 hour after initial set up to become completely chilled. Cooling light will turn off once the water has been fully chilled.
2. Press and hold the blue cold water button to dispense cold water. Release to stop dispensing. [Note: Water will dispense from the right spout.]

Dispensing Cool Water

1. Press and hold the light blue cool water button to dispense cool water. Release to stop dispensing. [Note: Water will dispense from the center spout.]

Dispensing Hot Water

1. Water will take approximately 12 minutes after initial set up to reach its hottest temperature. Heating light will turn off once the water has been fully heated.
2. Slide the red child lock back, then press down and hold the hot water button to dispense hot water. Release to stop dispensing. [Note: Water will dispense from the left spout.]

CAUTION: This unit dispenses water at temperatures that can cause severe burns. Avoid direct contact with hot water. Keep children and pets away from the unit while dispensing. Never allow children to dispense hot water without proper and direct supervision. Disable the heating feature by switching the heating convenience switch on the back of the unit to the OFF position or unplug the unit. Product is intended for water dispensing only. Do not use with other liquids.

Replacing the Bottle

1. Open dispenser cabinet door and slide empty bottle out of cabinet.
2. Remove probe assembly from the empty bottle and place it on the probe hanger.
3. Set empty bottle aside.
4. Remove the entire plastic cap from the new bottle.
5. Place probe into the new bottle and slide the collar down until it clicks into place. Press on the top of the probe until the tube touches the bottom of the bottle. For 11.3-liter bottles, squeeze the tabs on the top of the probe assembly to separate the probe cap from the collar and press the collar securely over the bottle opening.
6. Slide the bottle into the cabinet and close the door.

Cleaning & Maintenance

For best taste, performance, and hygiene, clean your cabinet, controls, bottle probe, and spouts regularly. Use a clean, soft cloth and food-grade sanitizer or bleach. Empty and clean drip tray as needed. Clean the cold reservoir regularly. Visit PrimoWater.ca for detailed cleaning instructions.