Kwikset SMARTCODE 917 RESIDENTIAL ELECTRONIC LEVER

Parts in the Box

• Latch (A)
• Exterior Assembly (B) - Traditional / Contemporary
• Interior Assembly - Traditional / Contemporary
• 9V Battery
• Strike (C)
• SmartKey™ Keys Tool (D)
• Spindle (F)
• Levers (J1, J2) - Traditional / Contemporary
• Allen Wrench (H)
• Fasteners (N, Q, P, R)

Required Tools

• Ruler
• Phillips head screwdriver
• Hammer
• Wood block
• Flathead screwdriver

For assistance, contact Kwikset at 1-800-327-5625 or visit www.kwikset.com.

1. Prepare the Door and Check Dimensions

If drilling a new door, use the supplied template and complete door drilling instructions available at www.kwikset.com/doorprep.

A. Door Hole Diameter: Measure to confirm the hole in the door is 2-1/8" (54 mm).

B. Backset: Measure to confirm the backset is either 2-3/8" or 2-3/4" (60 or 70 mm).

C. Door Edge Hole: Measure to confirm the hole in the door edge is 1" (25 mm).

D. Door Thickness: Measure to confirm the door is between 1-3/8" and 1-3/4" (35 mm and 44 mm) thick.

Note: If installing this lever below an existing lock or planning to install a lock above it, ensure the distance between holes is at least 6-1/2" (165 mm).

2. Install the Latch and Strike

A. Install Latch: Hold the latch in front of the door hole with the latch face flush against the door edge.

B. Check Latch Hole Centering: If the latch holes are centered in the door hole, no adjustment is required. Proceed to the next step.

C. Chiseled Door Edge: If the door edge is chiseled, use a flathead screwdriver to lift tabs on the collar of the rectangular face to remove it from the latch, then install the drive-in collar. Align tabs with holes in the collar and ensure the collar snaps into place. Pull the collar to test for a tight fit.

D. Install Latch: Install the latch into the door using the supplied screws (N, 2x) or by using a wood block and hammer for the drive-in type. Ensure the slant of the latch bolt faces the door frame.

E. Install Strike: Install the strike (P, 2x) on the door frame.

3. Install the Exterior Keypad, Spindle, and Interior Assembly

A. Install Exterior Keypad: Install the exterior keypad (Q).

B. Install Spindle: Insert the spindle (F) into the lock mechanism, ensuring the rounded edge faces the latch.

C. Optional Security Set Screw: Install the optional security set screw (R). This locks the interior cover and prevents easy access to the battery and Program button.

D. Connect Cable: Route the cable (K) under the latch and connect it securely to the interior assembly. Route the cable through clips.

E. Install Interior Assembly: Install the interior assembly while holding the exterior assembly. Ensure the spindle fully engages with the interior assembly. Ensure a tight cable connection. Secure the interior assembly with mounting screws (Q, 2x). Ensure both interior and exterior assemblies are parallel to the door edge before securing. CAUTION: Do not use power tools. Note: Tighten screws evenly and do not overtighten.

Note: Make sure to keep your door open until you have programmed a user code.

4. Install Levers

A. Install Exterior Lever: Install the exterior lever (J1 or J2), ensuring the lever handle faces away from the latch and the hole is on the bottom.

B. Insert Key and Turn: Insert the key and turn it 90° clockwise.

C. Secure Exterior Lever: Tighten the pre-installed set screw on the exterior lever. Turn the key back to the vertical position and remove it. This step is necessary to access the set screw on the exterior lever.

D. Install Interior Lever: Install the interior lever (J1 or J2), ensuring the lever handle faces away from the latch.

E. Secure Interior Lever: Tighten the pre-installed set screw on the interior lever.

TIP: You may need to jiggle the handle while pushing to ensure it is fully engaged.

5. Test Latch Operation

Close the door and test the latch operation. Make adjustments as needed.

The small bolt of the latch should not enter the strike hole. If it enters the strike hole, reposition the strike.

If the latch is loose in the strike, adjust the strike tab so it grips the latch bolt better when the door is closed.

6. Install Battery

A. Remove Interior Cover: Remove the interior cover. If you installed the security screw in step 3C, you will need to remove it to install the battery.

B. Connect Battery: Connect the 9V battery (M).

C. Secure Battery: Secure the battery into the interior assembly.

7. Add User Codes

Move swiftly during programming. If no digit is pressed for 10 seconds, the system will time out and you will need to restart the procedure.

Make sure the door is open.

A. Press Program Button: Press and release the Program button. You will hear two beeps.

B. Press 1: Press 1. You will hear one short beep and the keypad will flash green once.

C. Press Kwikset: Press Kwikset.

D. Enter User Code: Enter a User Code. It must be between 4 and 8 digits. For security reasons, the first 4 digits of each user code must be unique (e.g., you cannot program 1-2-3-4-5 and 1-2-3-4-6).

E. Press Kwikset: Press Kwikset.

F. Confirmation: You will hear one long beep and the keypad will flash green if successful. If you hear three beeps and the keypad flashes red, it was unsuccessful. Repeat from step A.

Reinstall battery cover.

8. OPTIONAL: Enable / Disable Programming Code

A Programming Code enables changes without needing to access the Program button, ideal for landlords. Once enabled, the Program button is disabled and can only be used for factory reset.

Make sure the door is open.

A. Initiate Programming: If you have not enabled a Programming Code, press and release the Program button (you will hear two beeps). If you have enabled one, enter your Programming Code, then press Kwikset (you will hear one short beep and the keypad will flash green).

B. Press 3: Press 3. You will hear one short beep and the keypad will flash green.

C. Press Kwikset: Press Kwikset.

D. Enter Programming Code: Enter a Programming Code (4-8 digits, cannot be the same as any user code).

E. Press Kwikset: Press Kwikset.

F. Re-enter Programming Code: Re-enter the Programming Code.

G. Press Kwikset: Press Kwikset. You will hear one long beep and the keypad will flash green if successful. If you hear three beeps and the keypad flashes red, it was unsuccessful. Repeat from step A.

9. Test the Lock and Review Lock Functionality

Unlocking the Door with a User Code

With the door open and turnpiece set to the auto-lock position, confirm that programmed user codes can unlock the door. Enter the user code; the lock will beep twice to indicate it unlocked. Tip: Press the Kwikset button before entering your user code to light up the keypad at night.

Unlocking the Door with a Key

To unlock using a key, turn the key clockwise to the horizontal position, then turn the lever to open the door. To remove the key, turn it back to the vertical position.

Turnpiece Functions - Choosing a Mode

• Auto-lock mode: Turnpiece in vertical position. Lock beeps once when turned to vertical. Key or code is needed for entry from the outside.
• Passage mode: Turnpiece in horizontal position. Lock beeps twice when turned to horizontal. Stays unlocked, allowing entry without a key or code.

Emergency Egress

The interior lever of this lock will always open the door when turned, regardless of whether it is locked or unlocked, allowing for safe and easy exit in case of emergency.

Re-key the lock (if needed)

1. IMPORTANT: Remove lever before re-keying.

2. Re-key: Re-key the lock to work with your existing key. See the supplied SmartKey™ Re-key instructions for more information.

Reference Guide

SmartCode 917 at a Glance

Components include: Exterior, Keypad, SmartKey tool hole, Keyway, Interior (cover removed), 9V Battery, Program button, Turnpiece.

System Signals

Additional Programming Features

How to add permanent or one-time User Codes

1. Make sure the door is open.
2. If no Programming Code is enabled, press and release the Program button (2 beeps). If enabled, enter Programming Code, press Kwikset (1 short beep, green flash).
3. Press 1 for a permanent user code or 7 for a one-time user code. 1 short beep, green flash.
4. Press Kwikset.
5. Enter new User Code (4-8 digits, first 4 unique).
6. Press Kwikset. 1 long beep, green flash if successful; 3 beeps, red flash if unsuccessful. Repeat from step 1 if needed.

How to enable/disable User Codes

If User Codes are disabled, the lock can only be operated by the key.

1. Make sure the door is open.
2. Initiate programming (as in step 7.A).
3. Press 6. 1 short beep, green flash.
4. Press Kwikset. 1 long beep, green flash if successful; 3 beeps, red flash if unsuccessful. Repeat from step 1 if needed.

How to mute/unmute lock

Muting disables beeping during operation and programming, but the low battery alarm remains.

1. Make sure the door is open.
2. Initiate programming (as in step 7.A).
3. Press 5. 1 short beep, green flash.
4. Press Kwikset. 1 long beep, green flash if successful; 3 beeps, red flash if unsuccessful. Repeat from step 1 if needed.

How to delete individual User Codes

1. Make sure the door is open.
2. Initiate programming (as in step 7.A).
3. Press 2 to delete a user code. 1 short beep, green flash.
4. Press Kwikset.
5. Enter the User Code to delete. Press Kwikset.
6. Enter the User Code again. Press Kwikset. 1 long beep, green flash if successful; 3 beeps, red flash if unsuccessful. Repeat from step 1 if needed.

How to delete all User Codes

1. Make sure the door is open.
2. Initiate programming (as in step 7.A).
3. Press 4. 1 short beep, green flash.
4. Press Kwikset.
5. Enter 9-9-9-9-9-9.
6. Press Kwikset.
7. Enter 9-9-9-9-9-9.
8. Press Kwikset. 1 long beep, green flash if successful; 3 beeps, red flash if unsuccessful. Repeat from step 1 if needed.

How to change the auto-locking duration

1. Make sure the door is open.
2. Initiate programming (as in step 7.A).
3. Press 8. 1 short beep, green flash.
4. Press Kwikset.
5. Enter delay time between 1-99 seconds.
6. Press Kwikset. 1 long beep, green flash if successful; 3 beeps, red flash if unsuccessful. Repeat from step 1 if needed.

How to enable/disable turnpiece functionality

A feature for property managers: If the turnpiece is disabled, the lock will always auto-lock after each entry. The turnpiece will rotate but will not activate passage mode. User code or key will always be required for entry.

1. Make sure the door is open.
2. Initiate programming (as in step 7.A).
3. Press 9. 1 long beep, green flash.
4. Press Kwikset. 1 long beep, green flash if successful; 3 beeps, red flash if unsuccessful. Repeat from step 1 if needed.

Factory Reset

A factory reset will delete all codes associated with the lock.

1. Make sure the door is open and unlocked.
2. Press and hold the Program button until you hear one long beep (approximately 30 seconds), then release the Program button.
3. Press and release the Program button again. You will hear one short beep.
4. Test with an existing User Code; the lock should not work.

Troubleshooting

• Keypad is not responding: Change battery.
• Desired user code cannot be programmed: For security reasons, the first 4 digits of each user code must be unique.
• Key cannot be removed when unlocked: This is a feature to ensure the door is always locked (store room function). To remove the key, return it to the vertical position.
• Emergency egress function: This lock allows exit by turning the lever on the inside, regardless of lock mode.

Regulatory Compliance

This product complies with standards established by the following regulatory bodies:

• Federal Communications Commission (FCC)
• Industry Canada

FCC: This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received. This equipment has been tested and found to comply with Class B digital device limits, designed to provide reasonable protection against harmful interference in residential installations. If interference occurs, try reorienting the antenna, increasing separation, connecting to a different outlet, or consulting a technician. Changes not expressly approved by the manufacturer could void the user's authority to operate the equipment.

Industry Canada: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation.

Important Safeguards

1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all users of safety precautions.
4. Protect your user codes and programming code.
5. Dispose of used batteries according to local laws and regulations.

CAUTION: Prevent unauthorized entry. Restrict access to the back panel and routinely check user codes, as anyone with access can change them. A program code can help protect system settings.

WARNING: No lock provides complete security. This lock may be defeated by forcible or technical means, or entry elsewhere. No lock substitutes for caution, awareness, and common sense. Consult a qualified locksmith or security professional for enhanced security.