Kwikset 54529-003 Installation Guide

Tools and Parts

Required Tools

• Screwdriver (Phillips head)

Parts in the Box

• Latch
• Screws (B1, B2)
• Passage Levers
• Privacy Levers
• Strike Plate
• Allen Wrench (Emergency Unlock Tool) ?
• Battery (AAA)

Additional Tools (if needed)

• Wood block
• Drill (if new hole required)
• Measuring tape
• Pencil
• Hammer (for strike plate installation)
• Flathead screwdriver (for alignment guide removal)

Installation Instructions

Step 1: Prepare Door and Check Dimensions

If drilling a new door, use the supplied template and complete door drilling instructions available at kwikset.com/doorprep.

Verify door dimensions:

• Backset: 2-3/8" (60 mm) or 2-3/4" (70 mm)
• Door Thickness: 1-3/8" - 1-3/4" (35 mm - 44 mm)
• Door Hole Diameter: 2-1/8" (54 mm)
• Door Edge Bore: 1" (25 mm)

[Visual Description: Diagram showing measurement points on a door for backset, thickness, and hole diameter. Includes a template outline.]

Step 2: Adjust Latch Backset

Hold the latch in front of the door hole, with the latch face flush against the door edge.

Check if the semi-circular hole in the latch is centered in the door hole. If it is centered, no adjustment is required. Proceed to Step 3.

If the semi-circular hole is NOT centered, adjust the latch:

Latch Adjustment (if needed): Grasp the pin on both sides of the latch and move it to the longer setting for a 2-3/4" backset, or the shorter setting for a 2-3/8" backset.

[Visual Description: Diagram showing the latch mechanism. A pin is visible, with arrows indicating how to move it to adjust the backset. One position is labeled 'centered' and the other 'not centered'.]

Step 3: Install Latch

For square chiseled doors only, ensure the door edge is chiseled.

Remove the latch plates.

Install the drive-in collar if the door edge is not chiseled.

Insert the latch into the door hole. Ensure the slant of the bolt faces the direction the door closes. ➡️

[Visual Description: Two options for latch installation are shown: one for doors with a chiseled edge, and one for doors without a chiseled edge using a drive-in collar. The correct orientation of the latch bolt's slant is emphasized.]

Step 4: Install Levers

For Passage Levers: Insert the spindle through the semi-circular hole in the latch. ➡️

For Privacy Levers: Insert the spindle through the semi-circular hole in the latch. ➡️

[Visual Description: Diagrams illustrating the insertion of the spindle through the latch mechanism for both passage and privacy lever types.]

Push up on the lever base while tightening the screws to keep the latch horizontal and centered. ✔️

Ensure straight edges of the lever base are parallel to the door edge.

If the lever base will not sit flush on the door, use a flathead screwdriver to remove the alignment guide. ?️

Privacy Levers Only: After tightening screws, rotate the interior lever to unlock it. ?

[Visual Description: Diagrams showing the lever installation process, including tightening screws, ensuring proper alignment, and the final unlocking step for privacy levers.]

Note on Lever Placement: The lever can be displayed on the interior or exterior of your door. This product is designed for installation exclusively on interior doors as its electric components make it unsuitable for exterior use. Kwikset will not assume any liability for any damages resulting from installing this product on the exterior of the home.

Step 5: Install Strike on Door Frame

Install the strike plate on the door frame using the provided screws. ?

Close the door and test latch operation. If the latch is loose in the strike, adjust the strike tab to grip the latch bolt better when the door is closed. ⚙️

[Visual Description: Diagrams illustrating the installation of the strike plate on the door frame and how to adjust the strike tab for a secure fit.]

Privacy Lock Features

Emergency Unlock Tool

The Allen wrench ? doubles as a bedroom/bathroom emergency unlock tool. Save for future use.

To unlock, insert the wrench and press with force. ➡️

[Visual Description: Illustration showing the Allen wrench being inserted into a small hole on the privacy lever to unlock it.]

Battery Management

Battery Installation

Remove the battery pack by pressing the tab on the back of the lever and pulling it out. ⬆️

Install one (1) AAA battery provided. Ensure to remove the plastic wrapper on the battery before installing. ?

Insert the battery pack and push gently until you hear a "click". Ensure correct polarity. ➕➖

[Visual Description: Diagrams showing how to remove the battery pack, insert a new battery with correct polarity, and reinsert the pack until it clicks.]

Battery Replacement

Remove the battery pack by pressing the tab on the back of the lever and pulling it out. ⬆️

Remove the old battery. ❌

Install one (1) AAA battery. For best results, use new, alkaline batteries only. Ensure the wrapper is removed before installing.

Insert the battery pack and push gently until you hear a "click".

[Visual Description: Diagrams illustrating the process of removing the old battery and installing a new one into the battery pack.]