Fortin EVO ONE Regular Installation Addendum

Vehicle Functions Supported

The following vehicle functions are supported by this diagram, if equipped:

Firmware and Installation Options

The current firmware version is 70.[41] (GM Minimum). To add the firmware version and options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

Bypass Programming Options

Program bypass option: Programmez l'option du contournement:

Remote Starter Options

If the vehicle is not equipped with a functional hood pin:

Option A11: Hood trigger (Output Status). Contact de capot (état de sortie).

Program Remote Starter Option for R.S. OEM Remote Stand Alone

Programmez l'option démarreur à distance pour Télécommande d'Origine Stand Alone:

Mandatory Installation Items

Hood Pin Status: The hood pin switch (included) must be installed if the vehicle can be remote started with the hood open. Set Function A11 to OFF.

Security Sticker: The security sticker is an essential security element and must be installed.

Notice: The installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.

Technician Warning: This module must be installed by a qualified technician. A wrong connection can cause permanent damage to the vehicle.

Connector Identification

The following connectors are key to the installation:

• Ignition Connector*: Connecteur d'ignition*. Wires include (+)ACCESSORY, (~)V DATA, (+)IGNITION, (+)12V BATTERY.
• Ignition Barrel: Barillet d'ignition.
• Transponder Connector: Connecteur du transpondeur. Wires include (+)12V IMMO, (~)CAN SW.
• Parking Light Switch: Feux de stationnement.

Wiring Connection Guide

This section details the wiring connections for the EVO ONE module to the Cadillac Escalade.

Main Harness Connections (EVO ONE Module):

• (+)Ignition: Yellow wire to A1
• Purple wire to A2
• Purple/White wire to A3
• Green wire to A4
• White wire to A5
• Orange wire to A6
• Orange/Black wire to A7
• Dark Blue wire to A8
• Red/Blue wire to A9
• Light Blue/Black wire to A10
• Black wire to A11
• (-)Parking Lights: Pink wire to A12
• Yellow/Black wire to A13
• Brown/White wire to A14
• (-)HOOD: Pink/Black wire to A15
• Purple/Yellow wire to A16
• Green/White wire to A17
• V DATA: Green/Red wire to A18
• White/Black wire to A19
• Light Blue wire to A20
• (+)Accessory: White wire to E1
• (+)12V: Orange wire to E2
• (-)Ground: Red wire to E3
• (+)Ignition: Black wire to E4
• Pink wire to E5
• Yellow wire to E6

CAN SW Connections:

• C5: Brown
• C4: Gray/Black
• C3: Gray
• C2: Orange/Brown
• C1: Orange/Green

(+)12V IMMO Connections:

• D6: White/Red
• D5: White/Blue
• D4: White/Green
• D3: Yellow/Red
• D2: Yellow/Blue
• D1: Yellow/Green

Important Notes:

• Automatic Transmission Mode: CUT LOOP FOR AUTOMATIC TRANSMISSION MODE. COUPEZ LA BOUCLE POUR LE MODE TRANSMISSION AUTOMATIQUE.
• Power Source: Use a more powerful 12V source if your system requires more than 2 Amp. Utilisez une source 12V plus puissante si votre système à besoin de plus de 2 Amp.
• Ground Connection: Connect to a solid ground point.

Connector Views:

• Ignition Connector (6-pin): Back view of black connector.
• Transponder Connector (4-pin): Back view of black connector.
• Parking Light Switch (16-pin): Back view of black connector at the steering column.

Note: The connector may differ from the one shown.

Key Bypass Programming Procedure 1/2

Follow these steps to program the key bypass:

1. Step 1: Press and hold the programming button. Connect the 6-PIN Main harness (White connector). The Blue, Red, Yellow, and Blue & Red LEDs will illuminate alternately.
2. Step 2: Release the programming button when the LED is BLUE. If the LED is not solid BLUE, disconnect the 6-Pin connector (Main-Harness) and go back to step 1.
3. Step 3: Insert the required remaining connectors.
4. Step 4: Turn the key to the Ignition ON/RUN position. The BLUE LED will flash rapidly.
5. Step 5: Press and release the programming button once (1x). The Blue LED will turn OFF. The YELLOW and RED LEDs will alternate.
6. Step 6: Turn the key to the OFF position.
7. Step 7: Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.

Key Bypass Programming Procedure 2/2

8. Step 8: Use the tool: FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu. This requires a Microsoft Windows computer with an Internet connection or a smartphone with an internet provider (charges may apply). Parts required are not included.
9. Step 9: After DCryptor programming is completed, go back to the vehicle and reconnect the 6-Pin (Main-Harness) or the 4-pins (Data-Link) connector, and then all the remaining connectors.

The module is now programmed.

Remote Starter / Alarm Verification Procedure

Test the remote starter. Remote start the vehicle.

Remote Starter Functionality

Follow these steps for remote starter functionality:

• All doors must be closed.
• Remote start the vehicle.
• Unlock the doors with the remote-starter remote or the OEM remote.
• Insert and Turn the key to the Ignition ON/RUN position.
• Press the brake pedal.
• The vehicle can now be put into gear and driven.

Notices and Support

Firmware and Installation Guides

Updated firmware and installation guides are posted on the Fortin website on a regular basis. It is recommended to update this module to the latest firmware and download the latest installation guide(s) prior to installation.

Visit www.fortinbypass.com for the latest version.

General Warning

The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible for damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by a qualified technician. The information supplied is a guide only. This instruction guide may change without notice.

Tech Support

Tel: 514-255-HELP (4357) | 1-877-336-7797

Website: www.fortinbypass.com

Copyright © 2006-2018, FORTIN AUTO RADIO INC. ALL RIGHTS RESERVED. PATENT PENDING.