Halo Plus Back To Back Frame Instruction Manual

Table of Contents

• Component Parts
• Assembly Instructions
• Use Instructions
• Troubleshooting
• Important Safety Instructions
• Advanced Programming

Component Parts

The following table lists all components included with the Halo Plus Back To Back Frame. An exploded view diagram shows the arrangement of these parts.

Diagram Description: An exploded view showing the two main desk frame structures, lifting columns, crossbeams, brackets, control box, handset, cables, and hardware. The left side shows the components for one leg, and the right side shows the components for the second leg, with connecting elements in the middle.

Assembly Instructions

Step 1: Adjust Top Frame Length

Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.

Diagram Description: Shows the top frame components with bolts highlighted. Arrows indicate loosening the bolts and extending/retracting the frame sections to adjust the width.

Step 2: Attach Lifting Columns

Insert the lifting column into the top frame and secure it with 4 pcs of M6x12 screws.

Diagram Description: Close-up view shows a lifting column being inserted into a mounting point on the top frame. Screws are shown being inserted to secure it. Arrows indicate the direction of insertion for the column and screws.

Step 3: Attach Side Brackets

Place the side bracket on the top frame and tighten the bolts.

Diagram Description: Shows a side bracket being positioned on the top frame. Arrows indicate tightening the bolts to secure it. The diagram illustrates the placement for both sides of the frame.

Step 4: Install Screen Brackets

Install the screen brackets using 8 pcs of M6x10 Bolts.

Diagram Description: Shows two screen brackets, each with mounting holes. Multiple M6x10 bolts are depicted ready for installation onto the brackets.

Step 5: Connect Beam and Mount Components

Insert the connected beam and tighten the pre-installed bolts. Mount the control box to the frame, and ensure all cables are connected correctly and tightly to the control box.

Diagram Description: Shows the connected beam being slotted into place between the lifting columns. The control box is shown being attached to the frame, with motor cables and handset cables connecting to it. Arrows indicate cable connections.

Step 6: Mount Tabletop and Handset

Mount the tabletop and fix it with 26 pcs screws ST4x20. Fix the centre bracket with 2 pcs screws M6x10. Fix the handset with 2 pcs screws ST4x20. Mount the control box to the frame, and ensure all cables are connected correctly and tightly to the control box. (Note) Desk will not function properly unless the control box has been connected to the desk frame bracket.

Diagram Description: Shows the tabletop being placed on the assembled frame. Screws are shown securing the tabletop. The centre bracket and handset are also shown being attached to the frame.

Step 7: Cable Management

Use the provided cable ties to tidy up any loosely hanging cables. Tighten the bolts on the top frame.

Diagram Description: Shows cables being organized and secured with cable ties along the frame. Arrows indicate tightening bolts on the top frame.

Cable Tray Installation

Fix the cable tray (B2-B2BCT) to the Back-to-Back desk frame with 8 pcs M6x10 screws.

Diagram Description: Shows the desk frame with the cable tray positioned underneath. Arrows indicate where the 8 M6x10 screws should be inserted to attach the tray.

Screen Panel Installation

Shush30 Privacy Screen

Step 1: Insert Tapped Plates

Insert the tapped plates into the screen panel. (Plates can be found in the B2-BBRAC carton).

Diagram Description: Close-up view of a screen panel edge showing slots where tapped plates are inserted.

Step 2: Attach Screen Brackets to Extrusion

Install the screen brackets (B2-BBRAC) to the Shush30 Extrusion with 8 pcs M5x6 screws.

Diagram Description: Shows a Shush30 extrusion profile with screen brackets being attached using screws. Arrows indicate the mounting points.

Step 3: Fix Screen Brackets to Desk Frame

Fix the screen brackets (B2-BBRAC) to the desk frame with 8 pcs M6x10 screws.

Diagram Description: Shows the assembled screen panel with brackets attached to the desk frame using M6x10 screws.

EPS (900mm H Eco Panel) Screen Panel Installation

Step 1: Install Screen Brackets

Install the screen brackets (B2-BBRAC) with 8 PCS M6x10 Screws. The brackets' direction should be as shown in the photos.

Diagram Description: Shows screen brackets being attached to the desk frame with M6x10 screws, indicating the correct orientation.

Step 2: Mount EPS Panel

Place the EPS panel on the screen brackets. Using a 6mm drill bit (not included), drill holes in the Eco Panel Screen in line with the back-to-back screen bracket holes. (Note: Carbide Drill Bits Work Best For PET panel). Place 8 x Double Ended Bolts M5*32mm - 6mm through the screen bracket (B2-BBRAC) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with an Allen key.

Diagram Description: Shows the EPS panel being placed on the brackets. A close-up illustrates drilling holes and inserting double-ended bolts through the bracket and panel.

Use Instructions

A. Parts List

This section reiterates the main components:

• 1. Lifting Column: 2 pcs
• 2. Handset: 1 pcs
• 3. Control Box: 1 pcs
• 4. Motor Cable: 1 pcs
• 5. Power Cord: 1 pcs

B. Technical Specifications

• Input: 100-240VAC
• Output Power: 29VDC
• Maximum accepted weight: 120 kg (including tabletop weight)
• Maximum speed: 38 mm/s
• Minimum height: 620mm
• Travel distance: 650 mm
• Operating temperature: 0-40°C
• Duty Cycle: Max.10% or 2 min on and 18 min pause

Cable Connection Diagram:

Diagram Description: A schematic shows the wiring connections. The control box is central, with power cord input, motor cables connecting to two lifting columns, and a handset connected via a cable. Arrows indicate the flow of power and data.

Control Panel Operation and Programming Instructions

Image Description: A close-up of the control panel handset displaying "78.2 M 1 23 >".

1. Connection Check: Ensure all components (control box, control panel, power cable, connecting cable, lifting columns) are correctly connected.
2. Power On: Connect the power cable to a 110/240VAC outlet. The control panel will display "62.0" for a few seconds, indicating the system is on and ready.
3. Up and Down:
   • Press and hold the "UP" button to move the desk up to the desired height. The desk stops when the button is released.
   • Press and hold the "DOWN" button to move the desk down to the desired height. The desk stops when the button is released.
4. Memory Settings:
   • After adjusting the desk height, press the "M" button.
   • Press a desired button (1, 2, or 3) to assign the current height to that memory preset. Up to 3 different heights can be saved.
   • To move the desk to a preset height, press the corresponding button (1, 2, or 3).
   • You can stop the desk during operation by pressing either the "UP" or "DOWN" button.
5. Keypad Lock:
   • To lock: Press and hold "UP" and "DOWN" buttons for 5 seconds until "LOC" appears on the display.
   • To unlock: Press and hold "UP" and "DOWN" buttons for 5 seconds simultaneously until "LOC" disappears and the height is displayed.
6. Reset:
   • If the system experiences a problem or the control panel displays "RES", a reset is required.
   • Press and hold the "DOWN" button throughout the process.
   • After 5 seconds, the desk will lower slightly to its lowest height, then rise slightly. The display will change back to the numeric height setting. The reset is complete when the desk stops.

Troubleshooting

1. HOT:

   Issue: Operation of the control box continuously for more than 2 minutes.

   Solution: a. Wait 18 minutes. b. Disconnect the power cable, wait a few minutes, then plug it back in. The error code will disappear.

2. E01 and E02:

   Issue: a. Control box cable not connected properly, defective, or broken. b. Weight on one side exceeds 120 kg.

   Solution: Ensure all connection cables are properly connected. Wait 3 seconds for the error code to disappear. If persistent, replace the engine. Remove load from the desk; the error code will disappear automatically.

3. E06:

   Issue: Difference between lifting columns is higher than 1 cm (0.4 inches).

   Solution: Start the "Reset" process.

4. E07:

   Issue: Load weight exceeds the limit of 120 kg.

   Solution: Remove items from the desk to ensure the total weight does not exceed 120 kg.

5. E08:

   Issue: Input voltage is lower than required.

   Solution: The error code will disappear automatically when the voltage increases to the required level.

6. E09:

   Issue: Input voltage is too high.

   Solution: The error code will disappear automatically when the voltage decreases to the supported level.

7. E10:

   Issue: Control panel not connected or not receiving power, while the control box is powered.

   Solution: Wait 1 second for the error code to disappear automatically. If persistent, check connection cables.

Important Safety Instructions

• Read operating instructions carefully and keep the manual for future reference.
• Before use, check the desk and power cables for damage (cuts, deep scratches). Do not turn on if damaged.
• Ensure power supply voltage is compatible with product parameters before connecting.
• Ensure the power cable length is sufficient for connection.
• The height-adjustable desk contains electronic circuits and should only be used in dry environments. Avoid outdoor or dusty conditions, heat sources, and corrosive materials.
• Keep electrical components away from liquids. Never touch or handle the desk, power supply, control box, or cables with wet hands.
• Clean the product with a clean, dry, soft cloth. Disconnect power before moving or cleaning electrical components.
• Do not disassemble columns, control box, or control panel; this is considered user damage.
• Contains small parts; keep out of reach of children. Do not allow children to play with the device. Packing materials are not toys.
• Do not lay or sit on the worktop; the product is not for lifting people.
• Do not exceed the maximum permissible load weight.
• Product usage is limited to a 10% duty cycle (2 minutes operation, 18 minutes pause).
• The manufacturer is not liable for damage or injury resulting from improper use or non-compliance with safety instructions.

Advanced Programming

Image Description: A close-up of the control panel handset displaying "78.2 M 1 23 >".

The following section details advanced programming options for the control panel:

• 1Un - Display Units Setting: Change display to show heights in inches or centimeters.
• 2br - Handset Brightness Setting: Adjust the brightness level of the handset display.
• 3bE - Handset Sound: Enable or disable audible feedback for button presses.
• 4Fu - Upward Direction Anti-Collision Sensitivity: Adjust sensitivity to prevent collisions when moving up.
• 5Fd - Downward Direction Anti-Collision Sensitivity: Adjust sensitivity to prevent collisions when moving down.
• 6FS - Balance Sensitivity: Ensure the two columns work in sync.
• 7SH - Setting the New Lowest Display and Height Range: Adjust the minimum and maximum height limits.
• 8Hc - Setting Constant-touch & One-touch: Configure how the desk moves (continuous press vs. single press).
• 9St - Time Reminder Setting: Set reminders to stand up.
• 10H - Setting Bounce Height: Adjust the bounce height feature.
• 11r - Restore Factory Defaults: Reset all settings to factory defaults.
• 12d - Fatigue Test Mode: For factory use only.

Detailed Programming Steps:

1Un - Display Units Setting

Change the numeric display to show heights in either inches or centimeters.

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "S" button, press "M" button to enter. Display shows "1Un". Press "M" button again to confirm the first setting.

1. The display will show [CM Symbol]. Press "S" button to select CM display. After 2 seconds, centimeters setting is done, and the current height (cm) will be displayed.
2. After displaying [Inches Symbol], press UP or DOWN. The display will show [Inches Symbol]. Press "S" button. After 2 seconds, inches setting is done, and the current height (inch) will be displayed.

2br - Handset Display Brightness

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "M" button, press "M" button to enter. Display shows "1Un".

1. Press UP/Down; it will display "2br".
2. Press "M" to enter. The current brightness level will be displayed: [Normal Brightness] (Normal brightness), [Low Brightness] (Low brightness), [High Brightness] (High brightness).
3. Press UP or DOWN to select the desired brightness level. Press "M" button to confirm. After 2 seconds, the current height will be displayed.

3bE - Handset Sound

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "S" button, press "M" button again to enter. Display shows "1Un".

1. Press UP or DOWN; it will display "3bE".
2. Press "M" button. The current sound status will be displayed: [OFF] (OFF: no sound) or [ON] (ON: with sound).
3. Press UP or DOWN to select OFF or ON. Then press "M" to confirm. After 2 seconds, the current height will be displayed.

4Fu - Upward Direction Anti-Collision Sensitivity

The desk has an Anti-Collision Sensitivity that stops movement if it hits something while moving up. You can change this sensitivity level.

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "M" button, press "M" button again to enter. Display shows "1Un".

1. Press UP or DOWN; it will display "4Fu".
2. Press "M" button to enter. The current anti-collision sensitivity level will be displayed. There are 9 levels for upward movement, from [L1] (most sensitive) to [L9] (least sensitive).
3. Press UP or Down to select your preferred level. Press "M" button to confirm. After 2 seconds, the current height will be displayed.

5Fd - Downward Direction Anti-Collision Sensitivity

The desk has an Anti-Collision Sensitivity that stops movement if it hits something while moving down. You can change this sensitivity level.

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "S" button, press "M" button again to enter. Display shows "1Un".

1. Press UP or DOWN; it will display "5Fd".
2. Press "S" button to enter. The current anti-collision sensitivity level for downward movement will be displayed, from [L1] (most sensitive) to [L9] (least sensitive).
3. Press UP or Down to select your preferred level. Press "M" button to confirm. After 2 seconds, the current height will be displayed.

6FS - Balance Sensitivity

The desk has a balance sensitivity feature to ensure the two columns always work in the same position. You can change this sensitivity level.

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "S" button, press "M" button again to enter. Display shows "1Un".

1. Press UP or DOWN; it will display "6FS".
2. Press "M" button to enter. The current balance sensitivity level will be displayed, from [L1] (most sensitive) to [L9] (least sensitive).
3. Press UP or Down to select your preferred level. Press "M" button to confirm. After 2 seconds, the current height will be displayed.

7SH - Setting the New Lowest Display and Height Range

The desk frame ships with default minimum and maximum height limits. These steps allow you to adjust the upper and lower limits to your preference.

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "S" button, press "M" button again to enter. Display shows "1Un".

1. Press UP or DOWN; it will display "7SH".
2. Press "M" button to enter. It will display [Lowest Position Height Display]. Press UP or DOWN; it will display [Set New Minimum Desk Height] and [Set New Maximum Desk Height].
3. Press UP or DOWN; it will display [Current Lowest Height]. Press "M" button to enter. Use UP or DOWN to set the lowest height display. Press "S" to confirm.
4. Press UP or DOWN; it will display [Current Lowest Height Position]. Press "M" button to enter. Use UP or DOWN to set a lowest height position. Press "M" to confirm.
5. Press UP or DOWN; it will display [Current Highest Height]. Press "M" button to enter. Use UP or DOWN to set a new highest height position. Press "M" to confirm.

8Hc - Setting Constant-touch & One-touch for Go Up or Down

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "M" button, press "M" button again to enter. Display shows "1Un".

1. Press UP or DOWN; it will display "8Hc".
2. Press "S" button to enter. It will display the current mode [001] or [002].
   • [001]: Keep pressing UP or DOWN button to make the desk move up or down.
   • [002]: Press UP or DOWN button and release; the desk will move up or down automatically. Press any button to stop the desk when it is moving.
3. Press "M" to confirm your desired mode. Wait 2 seconds; the setting is done.

9St - Reminder Setting

To promote a healthier working style, the desk can remind you to stand up after sitting for a long time. You can set this reminder.

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "M" button, press "M" button again to enter. Display shows "1Un".

1. Press UP or DOWN to get "9St".
2. Press "S" to enter. It will display "0.0H" (no time reminder; H means Hour).
3. Press UP or DOWN to select the desired reminder time (e.g., 1.5H means 1.5 hours). Press "S" to confirm.
4. Note: When the handset time reminder beeps, press any button to make it disappear. The time reminder will last 30 seconds if no operations are performed.

10H - Setting Bounce Height

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "M" button, press "M" button again to enter. Display shows "1Un".

1. Press UP or Down to get "10H".
2. Press "M" button to enter. It will show the current bounce height.
3. Press UP or DOWN to set the bounce height. Press "M" to confirm. Wait 2 seconds; it will display the current height.

11r - Restore Factory Defaults

Procedure: Press "M" button and hold for 3 seconds. Handset displays "S--". Release "M" button, press "M" button again to enter. Display shows "1Un".

1. Press UP or DOWN; it will display "11r".
2. Press "M" to enter. It will display [Factory Reset Symbol] and flash.
3. Press "M" to confirm. Wait 2 seconds; it will display the current height.

12d - Fatigue Test Mode

This mode is for factory use only. Please ignore this programming.