DALI MSENS HC TECTON II
Brand: Zumtobel Lighting GmbH
Reference: 00159920
Product Type: Sensor Luminaire
IP Rating: IP20
General Notices and Safety Information
? Important Notices: Please read first! Keep the instructions safe! Specifications are subject to change without notice! If you have questions, please contact the manufacturer.
⚠️ Caution: Risk of electric shock!
⚠️ Important: Hot plug-in is not an option and may cause damage to the lamp or luminaire!
The manufacturer is not liable for damages resulting from improper or faulty installation or operation or from unauthorized modifications to the luminaire.
Dimensions
The luminaire has the following dimensions:
- Length: 250 mm
- Width: 90 mm
- Height: 54 mm
⚠️ Chemical Resistance: Please note chemical resistance. Use only plastic-compatible cleaning agents. Gelieve enkel reinigingsmiddelen te gebruiken die Kunststofvriendelijk zijn.
Mounting Instructions
These instructions detail the mounting process for the DALI MSENS HC TECTON II luminaire onto the TEC2 track system.
Step 1a: Initial Track Connection
Connect the luminaire to the top of the start track. Ensure correct wiring by matching the function labels (FUNC.) to the terminal blocks. Observe the wiring configurations for L1, L2, L3, EL1, EL2, N, PE, DA+, DA-, EN1, EN2. A checkmark (✔️) indicates a correct connection, while a cross (❌) indicates an incorrect one. Refer to original document pages 10-13 for detailed diagrams.
Step 1b: Module Insertion and Locking
Insert the module into the track. The "CLIX" mechanism is used for secure locking. This step may be optional depending on the configuration.
Step 1c: CLIX Mechanism Detail
Close-up view of the CLIX locking mechanism, showing how it engages to secure the luminaire.
Step 2a-2d: Continued Mounting and Wiring
Further steps involve connecting the luminaire to the track and ensuring correct wiring. Pay close attention to the terminal assignments (L1, L2, L3, N, EN1, EN2, EL1, EL2) and the AC 220-240 V power supply. The CLIX mechanism is used again for securing.
Step 3: TEC2 Track System Installation
Mount the luminaire onto the TEC2 track system. This involves electrical connection and securing the unit. Diagrams illustrate the correct mounting and dismounting procedures.
Dismounting: Follow the numbered steps (1, 2) to safely remove the luminaire from the track.
Options and Compatibility
Optional Features: The luminaire may support optional features indicated by "OPTION!". Diagrams show potential signal propagation in a room, suggesting sensor functionality.
Compatibility: This luminaire is compatible with:
- LITECOM DALI-2
- DIMLITE pro G2
- basicDIM ILD G2
- TEC2 (TRIDONIC)
Detection and Measurement Capabilities
The luminaire is equipped with sensors for movement and light measurement.
Movement Detection
The movement detection cone has an angle of 72°. The detection range varies with mounting height (H) and results in a detection diameter (Ø):
| Mounting Height H (m) | Detection Diameter Ø (m) |
|---|---|
| 6.00 | 6.00 |
| 8.00 | 8.00 |
| 10.00 | 12.00 |
| 12.00 | 15.00 |
| 14.00 | 18.00 |
| 16.00 | 20.00 |
Light Measurement
The light measurement range also depends on mounting height (H) and results in a measurement diameter (Ø):
| Mounting Height H (m) | Measurement Diameter Ø (m) |
|---|---|
| 8.00 | 1.80 |
| 12.00 | 2.70 |
| 16.00 | 3.70 |
Adjustment of Detection Area
The detection area can be adjusted. Diagrams illustrate settings for different ranges:
- 6-12 m low: Adjustment for lower mounting heights.
- 12-16 m high: Adjustment for higher mounting heights.
The detection angle 'a' can be set to 60° or 72°.
Adjustment parts/modules are identified by part numbers: 28001658, 28001660, 28001659.
Installation and Operation Instructions
General Requirements: Installation and commissioning, as well as any modifications, must be performed by authorized personnel (qualified electrician). National installation regulations must be observed.
Safety Precautions:
- Disconnect the luminaire from the mains before any work.
- Hot plug-in is prohibited and can damage the luminaire.
- ⚠️ Risk of electric shock.
Manufacturer Liability: The manufacturer is not liable for damages due to improper installation, operation, or unauthorized modifications.
Specifications: Subject to change without notice. For questions, contact the manufacturer.
