DOD Mini Volume Pedal Owner's Manual

Introduction

Thank you for purchasing the DOD Mini Volume Pedal, a miniature passive pedal that offers you full volume control without taking up valuable space on your pedalboard.

Features

• Compact form factor occupies minimal pedalboard space
• Long-throw pedal for full range of control
• High-quality, high-cycle 500 kΩ potentiometer for smooth volume adjustments
• Integrated treble bleed circuit prevents treble loss at lower volume settings
• Removable rubber feet for pedalboard mounting
• 1/4" TS input and output jacks
• Non-slip pedal surface
• Rugged construction

Configuration

1. Turn off your amplifier, then connect your cables (see connection diagram below).
2. Turn down your amplifier's volume, press the toe of the DOD Mini Volume Pedal down, then turn on your amplifier.
3. Slowly increase your amplifier's volume until you reach your desired level.

Connection Diagram

The diagram shows a typical setup: a guitar connects to the 'In' jack of the DOD Mini Volume Pedal. The 'Out' jack of the pedal connects to the input of a series of 'Effect Pedals'. The output of the effect pedals then connects to an amplifier. The text "USE ONLY UNBALANCED TS CABLES" is displayed below the diagram.

***Important Usage Note***

The two hex screws on the bottom of the pedal are part of the spring-loaded adjustment mechanism. If play develops over time, slightly loosen these screws and then retighten them. This will ensure the main drive gear tightens against the pedal gear. Do not remove these screws or operate the pedal while the screws are loose, as this can cause gear misalignment and pedal malfunction. There are no user-serviceable parts inside the pedal. The pedal should not be opened under any circumstances.

Conformity and Safety Instructions

The following is indicative of low-altitude use; do not use this product above 2000 m (6561 ft).

Warning Symbols:

• [Lightning bolt in triangle]: Indicates dangerous voltages are present inside the unit.
• [Exclamation mark in triangle]: Indicates that the user needs to refer to the owner's manual.

These symbols warn that there are no user-serviceable parts inside the unit. Do not open the unit. Do not attempt to repair the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer's warranty. Do not get the unit wet. If liquid is spilled on the unit, turn it off immediately and take it to a dealer for servicing. Unplug the unit during thunderstorms to prevent damage.

UK Mains Plug Warning

A molded mains plug that has been cut off from the cord is unsafe. Dispose of the mains plug in an appropriate disposal center. NEVER insert a damaged or cut-off mains plug into a 13 AMP socket. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your local dealer. Replacement fuses are 13 amp and MUST be ASTA approved to BS1362.

Disposal Information

If you wish to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation requiring proper treatment, recovery, and recycling. Private households in the 25 EU member states, in Switzerland, and Norway can return their used electronic equipment free of charge to designated collection centers or to a dealer (if purchasing a similar new product). For countries not mentioned above, please contact your local authorities for a correct disposal method. This will ensure that the disposed product undergoes the necessary treatment, recovery, and recycling, thus preventing potential negative effects on the environment and human health.

For Your Protection, Please Read the Following:

• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• For indoor use only.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Power Cord Instructions

Use only accessories/attachments specified by the manufacturer.

Unplug this apparatus during lightning storms or when unused for long periods of time. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades, one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Use only with the cart, stand, tripod, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

POWER SWITCH: The power switch used in this equipment does NOT interrupt the connection to the mains electricity.

MAINS DISCONNECTION: The plug must remain readily operable. For rack mounting or installations where the plug is not accessible, a mains switch with at least 3 mm contact separation in each pole must be incorporated into the rack or building's electrical installation.

If connected to a 240 V supply, a CSA/UL certified power cord suitable for this supply must be used.

Wiring Instructions

NOTICE TO CUSTOMERS IF UNIT IS EQUIPPED WITH A POWER CORD.

WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTH CONNECTION.

The cores of the mains cord are colored in accordance with the following code:

GREEN AND YELLOW - EARTH / BLUE - NEUTRAL / BROWN - PHASE

SINCE THE COLORS OF THE CORES OF THE MAINS CORD OF THIS APPARATUS MAY NOT CORRESPOND WITH THE COLORED MARKINGS IDENTIFYING THE TERMINALS OF YOUR PLUG, PROCEED AS FOLLOWS:

• The GREEN AND YELLOW COLORED CORE MUST BE CONNECTED TO THE TERMINAL IN THE PLUG MARKED WITH THE LETTER E, OR WITH THE EARTH SYMBOL, OR COLORED GREEN, OR GREEN AND YELLOW.
• The BLUE COLORED CORE MUST BE CONNECTED TO THE TERMINAL MARKED WITH N OR COLORED BLACK.
• The BROWN COLORED CORE MUST BE CONNECTED TO THE TERMINAL MARKED WITH L OR COLORED RED.

THIS APPARATUS MAY REQUIRE THE USE OF A MAINS CORD, A PLUG OR BOTH, DIFFERENT DEPENDING ON THE POWER SOURCE AVAILABLE AT THE TIME OF INSTALLATION. IF THE ATTACHMENT PLUG IS TO BE CHANGED, IT MUST BE DONE BY QUALIFIED SERVICE PERSONNEL WHO WILL REFER TO THE TABLE BELOW. THE GREEN/YELLOW WIRE MUST BE CONNECTED DIRECTLY TO THE CHASSIS OF THE UNIT.

WARNING: IF THE EARTH IS INCORRECTLY WIRED, CERTAIN FAULT CONDITIONS IN THE UNIT OR IN THE SYSTEM TO WHICH IT IS CONNECTED MAY CAUSE THE FULL MAINS VOLTAGE TO BE PRESENT BETWEEN THE CHASSIS AND EARTH. IF THE CHASSIS AND EARTH ARE TOUCHED SIMULTANEOUSLY, SERIOUS OR FATAL INJURIES CAN OCCUR.