DOD Mini Expression Pedal Owner's Manual

Thank you for purchasing the DOD Mini Expression Pedal, a miniature passive expression pedal that offers a full range of expressive control without taking up valuable space on your pedalboard.

Features

• The compact form factor occupies minimal space on the pedalboard.
• Long-travel pedal for a full range of control.
• High-cycle, high-quality 25 kΩ potentiometer for smooth, expressive control.
• Impedance switch changes from 25 kΩ (high/low) to 10 kΩ (center) to accommodate Line 6® style CV inputs.
• Removable rubber feet for pedalboard mounting.
• 1/4" jack with selectable TS, TRS, or RTS operation.
• Non-slip pedal surface.
• Rugged construction.

Setup

1. Connect the cables (see connection diagram below).
2. Select the correct cable connection setting (TS, TRS, or RTS) for the device you wish to control. (Consult the owner's manual of the controlled device to determine the correct setting.)
3. Press down the toe of the DOD Mini Expression Pedal.
4. Configure the controlled device for the desired expression control type.

Connection Diagram: The diagram shows a typical setup for the Mini Expression Pedal. On the left, an input jack labeled "In" is shown. On the right, there are output jacks labeled "Exp. Out" and "Exp. In", along with "Out" and "In" jacks. A DigiTech RP360 Effects Processor is depicted, with connections from the expression pedal to the processor's "Exp. In" and "Exp. Out" jacks. A guitar is shown connected to the input of the effects processor. Text below the diagram advises: "See the owner's manual for the controlled device to determine the proper cable to use with the expression pedal."

IMPORTANT USAGE NOTE

The two hex screws on the bottom of the pedal are part of the spring tension adjustment mechanism. If play develops over time, slightly loosen these screws and then re-tighten them. This will cause the main drive gear to mesh more tightly with the pedal gear. DO NOT remove these screws or operate the pedal while the screws are loose. This can cause gear misalignment and pedal malfunction. There are no user-adjustable parts inside the pedal. Under no circumstances should the pedal be opened.

Conformity and Safety Instructions

The following is indicative of low-altitude use; do not use this product above 2000 m.

The symbols shown above are internationally accepted symbols warning of potential hazards with electrical products. The lightning bolt [⚡] with an arrowhead in an equilateral triangle indicates that hazardous voltages are present within the unit. The exclamation mark [❗] in an equilateral triangle indicates that the user needs to refer to the owner's manual. These symbols warn that there are no user-serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer's warranty. Do not get the unit wet. If liquid is spilled on the unit, turn it off immediately and take it to a dealer for servicing. Unplug the unit during thunderstorms to avoid damage.

UK MAINS PLUG WARNING

A molded mains plug that has been cut off from the cord is unsafe. Dispose of the mains plug at an appropriate disposal center. NEVER, UNDER ANY CIRCUMSTANCES, INSERT A DAMAGED OR CUT-OFF MAINS PLUG INTO A 13 AMP SOCKET. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your local dealer. Replacement fuses are 13 amp and MUST be ASTA approved to BS1362.

If you wish to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling. Private households in the 25 EU member states, in Switzerland and Norway may return their used electronic equipment free of charge to designated collection points or to a retailer (if you are buying a similar new product). For countries not mentioned above, please contact your local authorities for the correct disposal method. This will ensure that the disposed product undergoes the necessary treatment, recovery, and recycling, thereby preventing potential negative effects on the environment and human health.

FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:

• READ THESE INSTRUCTIONS.
• KEEP THESE INSTRUCTIONS.
• HEED ALL WARNINGS.
• FOLLOW ALL INSTRUCTIONS.
• DO NOT USE THIS APPARATUS NEAR WATER.
• CLEAN ONLY WITH A DRY CLOTH.
• FOR INDOOR USE ONLY.
• DO NOT BLOCK ANY VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS.
• DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.

Additional Safety Instructions

• USE ONLY ACCESSORIES/ATTACHMENTS SPECIFIED BY THE MANUFACTURER.
• UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades, one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
• Use only with the cart, stand, tripod, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled, or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
• POWER SWITCH: The power switch used in this apparatus does NOT interrupt the connection to the mains power supply.
• MAINS DISCONNECTION: The plug must remain readily operable. For rack mounting or installations where the plug is not accessible, a readily accessible all-pole mains switch with a contact separation of at least 3 mm in each pole must be incorporated into the rack wiring or building wiring.
• If connected to a 240 V supply, a CSA/UL certified power cord suitable for this supply must be used.

Safety Instructions

NOTICE TO CUSTOMERS IF UNIT IS EQUIPPED WITH A POWER CORD.

WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTH CONNECTION.

THE CONDUCTORS OF THE POWER CORD ARE COLORED ACCORDING TO THE FOLLOWING CODE: GREEN AND YELLOW - EARTH / BLUE - NEUTRAL / BROWN - PHASE

SINCE THE CONDUCTOR COLORS OF THE POWER CORD OF THIS APPARATUS MAY NOT CORRESPOND WITH THE COLORED MARKINGS IDENTIFYING THE TERMINALS IN YOUR PLUG, PROCEED AS FOLLOWS:

• THE GREEN AND YELLOW COLORED CONDUCTOR MUST BE CONNECTED TO THE TERMINAL IN THE PLUG MARKED WITH THE LETTER E, OR WITH THE EARTH SYMBOL [⏻], OR COLORED GREEN, OR GREEN AND YELLOW.
• THE BLUE COLORED CONDUCTOR MUST BE CONNECTED TO THE TERMINAL MARKED WITH N OR COLORED BLACK.
• THE BROWN COLORED CONDUCTOR MUST BE CONNECTED TO THE TERMINAL MARKED WITH L OR COLORED RED.

THIS APPARATUS MAY REQUIRE THE USE OF A POWER CORD, A PLUG OR BOTH DIFFERENTLY, DEPENDING ON THE POWER SOURCE AVAILABLE AT THE TIME OF INSTALLATION. IF THE ATTACHMENT PLUG HAS TO BE CHANGED, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WHO WILL REFER TO THE TABLE BELOW. THE GREEN/YELLOW WIRE MUST BE CONNECTED DIRECTLY TO THE CHASSIS OF THE UNIT.

CAUTION: IF GROUND IS INCORRECTLY CONNECTED, DETERMINATE FAULT CONDITIONS IN THE UNIT OR THE SYSTEM TO WHICH IT IS CONNECTED MAY RESULT IN THE FULL MAINS VOLTAGE BETWEEN THE CHASSIS AND GROUND. IF THE CHASSIS AND GROUND ARE TOUCHED SIMULTANEOUSLY, SEVERE OR FATAL INJURY MAY RESULT.