DOD Mini Expression Pedal Owner's Manual

Introduction

Thank you for purchasing the DOD Mini Expression pedal, a miniature passive expression pedal that offers the full range of expressive control without taking up valuable space on your pedalboard.

Features

• Small form factor takes up minimal space on the pedalboard
• Long throw treadle for full range control
• High-quality, high-cycle 25kΩ potentiometer for smooth, expressive control
• The impedance switch changes from 25kΩ (top/bottom) to 10kΩ (center) to match Line 6®-style CC inputs
• Removable rubber feet for pedalboard mounting
• 1/4" jack connector with selectable TS, TRS, or RTS operation
• Non-slip tread pad
• Robust construction

Setup

1. Connect the cables (see connection diagram below).
2. Select the appropriate cable connection setting (TS, TRS, or RTS) for the device you wish to control. (Refer to the controlled device's user manual for determining the correct setting.)
3. Press down on the DOD Mini Expression pedal's treadle.
4. Configure the controlled device for the desired type of expression control.

Diagram Description: The diagram shows the DOD Mini Expression pedal connected to an effects processor (RP360) and a guitar. It illustrates the 'In' and 'Out' connections for the expression pedal and the 'Exp. In' and 'Exp. Out' connections for the effects processor. The text below the diagram states: "See the owner's manual for the controlled device to determine the proper cable to use with the expression pedal."

Important Usage Note

***IMPORTANT USAGE NOTE***

The two hex screws located on the bottom of the pedal are part of the spring adjustment mechanism. If you experience slippage over time, slightly loosen these screws and then retighten them. This will re-engage the main switch to the treadle's gear.

DO NOT remove these screws, nor operate the treadle while the screws are loose. This can cause gear slippage and improper pedal function. There are no user-adjustable parts inside the pedal. The pedal should never be opened under any circumstances.

Compliance and Safety Instructions

Altitude Warning: The following indicates low altitude operation; do not use this product above 2000m (⛰️ ≤2000m).

Symbol Explanations: The symbols shown above are internationally accepted symbols that warn of potential hazards associated with electrical products. A lightning bolt with an arrowhead in an equilateral triangle (⚡) means there are dangerous voltages in the unit. An exclamation mark in an equilateral triangle (❗) means the user must read the instruction manual.

General Warnings: These symbols warn that there are no user-serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Leave all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer's warranty. Do not wet the unit. If liquid is spilled on the unit, turn it off immediately and take it for service. Unplug the unit during thunderstorms to avoid damage.

UK MAINS PLUG WARNING: A molded mains plug that has been cut off from the cord is unsafe. Dispose of the mains plug in a suitable waste disposal facility. NEVER, UNDER ANY CIRCUMSTANCES, INSERT A DAMAGED OR CUT MAINS PLUG INTO A 13 AMP SOCKET. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your local retailer. Replacement fuses are 13 amps and must be ASTA approved to BS1362.

Disposal Information: When disposing of this product, do not mix it with general household waste. In accordance with legislation requiring proper treatment, recovery, and recycling, separate collection systems are in place for used electronic products. Households in the EU 25 member states, Switzerland, and Norway may return their used electronic equipment free of charge to designated collection points or to a retailer (if purchasing a similar new product). For countries not mentioned above, please contact your local authorities for information on the appropriate disposal method. This ensures that the disposed product undergoes the necessary treatment, recovery, and recycling, thus preventing potential negative effects on the environment and human health.

WARNING FOR YOUR PROTECTION READ THE FOLLOWING:

• READ THESE INSTRUCTIONS.
• KEEP THESE INSTRUCTIONS.
• HEED ALL WARNINGS.
• FOLLOW ALL INSTRUCTIONS.
• DO NOT USE THIS APPARATUS NEAR WATER.
• CLEAN ONLY WITH A DRY CLOTH.
• FOR INDOOR USE ONLY.
• DO NOT OBSTRUCT ANY VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS.
• DO NOT INSTALL NEAR ANY HEAT SOURCES, SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.
• USE ONLY ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.
• UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician to replace the obsolete outlet.

Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

POWER SWITCH: The power switch used in this equipment does not disconnect the mains connection.

AC DISCONNECT: The receptacle shall remain readily accessible. For rack-mounted or other installations where the plug may not be accessible, an all-pole main switch must be incorporated into the rack or building's electrical installation, with a contact separation of at least 3 mm in all poles. When connected to a 240V supply, a suitable CSA/UL certified power cord must be used for this supply.

Wiring Instructions

WARNING TO USERS, IF THE APPARATUS IS FITTED WITH A POWER CORD.

WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET WITH A PROTECTIVE EARTH CONNECTION.

The mains cord wires are coloured according to the following code:

GREEN AND YELLOW – EARTH / BLUE – NEUTRAL / BROWN – LIVE

AS THE COLOURS OF THE WIRES IN THE MAINS LEAD MAY NOT CORRESPOND WITH THE COLOURED MARKINGS IDENTIFYING THE TERMINALS OF YOUR PLUG, PROCEED AS FOLLOWS:

• ! CONNECT THE GREEN AND YELLOW WIRE TO THE TERMINAL MARKED WITH AN E LETTER (?) OR BY THE EARTH SYMBOL OR COLOURD GREEN OR GREEN AND YELLOW.
• ! CONNECT THE BLUE WIRE TO THE TERMINAL MARKED WITH AN N OR BLACK COLOUR.
• ! CONNECT THE BROWN WIRE TO THE TERMINAL MARKED WITH AN L OR RED COLOUR.

THIS APPARATUS REQUIRES THE USE OF EITHER A TWO-CORE OR THREE-CORE MAINS LEAD, DEPENDING ON THE POWER SOURCE BEING USED. IF THE PLUG HAS TO BE CHANGED, THIS MUST BE DONE BY QUALIFIED PERSONNEL WHO WILL USE THE TABLE BELOW.

THE GREEN/YELLOW WIRES MUST BE CONNECTED DIRECTLY TO THE CHASSIS TERMINAL OF THE UNIT.

WARNING: IF THE EARTHING IS ABOLISHED, CERTAIN FAULTS IN THE UNIT OR SYSTEM TO WHICH IT IS CONNECTED MAY RESULT IN THE CHASSIS BECOMING LIVE AND POSSIBLY CAUSING SERIOUS INJURY OR DEATH IF THE CHASSIS AND EARTH ARE SIMULTANEOUSLY TOUCHED.