ASSEMBLY INSTRUCTIONS
Product: Latitude Run Nightstand (Model: fmab1154)
Estimated Assembly Time: 90 minutes ⏱️
Required Persons: 1 ?
Parts List
- Part 1: Top Panel
- Part 2: Bottom Panel
- Part 3: Left Side Panel
- Part 4: Right Side Panel
- Part 5: Leg Frame (x2)
- Part 6: Back Panel
- Part 7: Support Bar (x2)
- Part 8: Drawer Front (x2)
- Part 9: Drawer Side (x4)
- Part 10: Drawer Back (x2)
- Part 11: Drawer Bottom (x2)
- Part 12: Drawer Slide Component (x2)
Hardware List
| Identifier | Description | Quantity |
|---|---|---|
| A | Dowel (Ø6 x 35mm) | x 12 |
| B | Cam Lock (Ø15 x 12mm) | x 12 |
| C | Dowel (Ø8 x 30mm) | x 8 |
| D | Screw (3.5 x 14mm) | x 16 |
| E | Screw (Ø7 x 40mm) | x 4 |
| F | Metal Rail Component | x 4 |
| G | Screw (M6 x 40mm) | x 12 |
| H | Screw (4 x 35mm) | x 8 |
| I | Screw (M4 x 18mm) | x 4 |
| J | Drawer Handle Component | x 2 |
| K | Allen Key (M4) | x 1 |
| L | Screw (M4 x 35mm / M3.5 x 14mm) | x 2 |
Assembly Steps
Step 1
Attach metal rail components (F1, F2) to the designated panels. Ensure the shrapnel is pushed upwards. ⬆️ Push the shrapnel up.
Hardware used: F (x4)
Step 2
Attach metal rail components (F1) to panels 3 and 4 using screws D. Attach panel 1 to panels 3 and 4 using screws D.
Hardware used: D (x8), F (x4)
Step 3
Insert dowels A into panel 1.
Hardware used: A (x4)
Step 4
Attach panels 3 and 4 to panel 1 using cam locks B and dowels C.
Hardware used: B (x4), C (x4)
Step 5
Slide back panel 6 into the grooves of panels 3 and 4. Ensure the correct orientation: Halogen faces inward. ➡️ Halogen faces inward.
Hardware used: None explicitly shown for this step, relies on grooves.
Step 6
Attach panel 2 to panels 3 and 4 using screws C and E. Use Allen key K for assembly. ?
Hardware used: C (x4), E (x4), K (x1)
Step 7
Assemble the leg frames (part 5) and support bars (part 7) using Allen key K and screws G.
Hardware used: K (x1), G (x8)
Step 8
Place the assembled leg structure from Step 7 onto the main unit (part 2) and secure it using Allen key K and screws G.
Hardware used: K (x1), G (x4)
Step 9
Assemble the drawer front (part 8) with drawer sides (part 9) and drawer bottom (part 11) using dowels A and screws I. Attach drawer handle component J.
Hardware used: A (x8), I (x4), J (x2)
This step is repeated for two drawers (x2).
Step 10
Assemble the drawer back (part 10) to the drawer sides (part 9) and drawer bottom (part 11) using screws H.
Hardware used: H (x8)
This step is repeated for two drawers (x2).
Step 11
Attach the drawer slide component (part 12) to the assembled drawer box.
Hardware used: None explicitly shown for this step, relies on pre-attached slides or grooves.
This step is repeated for two drawers (x2).
Step 12
Attach the drawer assembly to the main unit using cam locks B.
Hardware used: B (x8)
This step is repeated for two drawers (x2).
Step 13
Attach the drawer slide components (F2) to the drawer sides (part 9) using screws D. Attach the assembled drawer unit to the main unit using screws F.
Hardware used: D (x8), F (x4)
This step is repeated for two drawers (x2).
Step 14
Insert the assembled drawers into the main unit. The unit features a "Double-sided slide rail flush push-in" mechanism. ➡️ Double-sided slide rail flush push-in.
Note: The height of the drawer can be adjusted. ⚙️ The height of the drawer can be adjusted here.
Step 15
Attach hardware L to the top of the unit.
Hardware used: L (x2)
Step 16
Attach hardware L to the sides of the unit. Ensure proper alignment for attachment.
Hardware used: L (x2)
