Home Decorators Collection Vanity Series

Thank You

We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this vanity cabinet. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Home Decorators Collection!

Safety Information

Wood Dust Hazards

CAUTION: Sawing, sanding, or machining wood products can produce wood dust which can cause a flammable or explosive hazard.

WARNING: Modifications to this product can release wood dust, a substance known to the State of California to cause cancer.

Wood dust may cause lung, upper respiratory tract, eye, and skin irritation. Some wood species may cause dermatitis and/or respiratory allergic effects. The International Agency for Research on Cancer (IARC) has classified wood dust as a nasal carcinogen in humans.

• Avoid dust contact with ignition sources.
• Avoid prolonged or repeated breathing of wood dust in air.
• Avoid dust contact with eyes and skin.

First Aid: If inhaled, remove to fresh air. In case of contact, flush eyes and skin with water. If irritation persists, call a physician.

For a Wood Dust MSDS (Material Safety Data Sheet), contact www.masterbrand.com/regulatoryinformation

General Safety Warnings

CAUTION: Do not hang from the cabinet. ⚠️

DANGER: Failure to follow warnings and cautions could result in serious injury. Do not exceed the maximum load capacity. Do not stand on cabinet. Use cabinet on level ground.

WARNING: Base cabinet supports a maximum weight of 200 lbs (90.7 kg). Exceeding maximum weight limit will compromise the integrity of the cabinet structure and could cause the cabinet to fail.

One Year Limited Warranty

This is a general summary of the full Limited Warranty, including exclusions, limitations, and disclaimers. For a complete statement, please see www.homedepot.com.

The Product is warranted to be free from non-conformities in material and workmanship under normal use, from the date of purchase and for as long as the original consumer purchaser owns and lives in the home in which the Product is first installed. This Limited Warranty is only for residential use in the United States, Canada, or Mexico and ends when the original consumer purchaser transfers ownership or ceases to occupy the home.

If a non-conformity occurs during this period, the Seller will, free of charge, repair or replace the Product at its sole discretion. The Limited Warranty does not cover damage or failure caused by abuse, misuse, vandalism, negligence, accident, ordinary wear and tear, improper installation, cleaning, or maintenance (e.g., abrasive cleaners, chlorine cleaners, scuffing sponges, steel wool), environmental conditions (sunlight, smoke, extreme temperature/humidity), fire, flood, or Acts of God.

The Limited Warranty does NOT cover indirect or consequential damages, labor charges for installation or removal, or freight charges to return the Product. Seller's liability will not exceed the purchase price of the Product.

To the extent permitted by law, all other implied or express warranties are disclaimed, including warranties of MERCHANTABILITY and FITNESS FOR A PARTICULAR PURPOSE. The Limited Warranty gives the purchaser specific legal rights, which may vary by state or province.

For the full Limited Warranty, including all exclusions, limitations, and disclaimers, visit www.homedepot.com. Further information is also available by calling Home Decorators Collection Customer Service at 1-800-986-3460.

Pre-Installation

Tools Required

• Vanity Top: Cubierta para tocador / Revêtement de comptoir de meuble-lavabo
• Faucet: Grifo / Robinetterie
• Goggles: Gafas de seguridad / Lunettes de protection
• Tape Measure: Cinta de medir / Ruban à mesurer
• Phillips Head Screwdriver: Destornillador Phillips / Tournevis cruciforme
• 2-Foot Level: Nivel de 2 pies / Niveau de 61 cm (2 pi)
• Variable Speed Drill with 3/32 in. drill bit: Taladro de velocidad variable con broca de 3/32" / Perceuse à vitesse variable avec mèche de 3/32 po
• Utility Knife: Cuchilla multiuso / Couteau à lame rétractable
• Stud Finder: Detector de vigas / Détecteur de montant
• #10 x 2.5 in. or #10 x 3 in. cabinet screws: Tornillos para gabinete núm. 10 x 2.5". o núm. 10 x 3" / Vis de menuisier n°10 x 6,35 cm (2,5po) ou n°10 x 7,62 cm (3 po)

Step 1: Unbox and Inspect

Unbox and inspect your new bath cabinet(s). If damage is discovered, please call 1-800-986-3460.

Step 2: Wall Stud Location

Locate the wall studs with a stud finder and mark where the cabinets are to be installed. To make installation easier, remove all the doors and drawers from the cabinets before installation.

Installation

Step 1: Vanity Cabinet Installation

(If applicable):

1. Place your vanity base cabinet into the desired position.
2. Drill through cabinet back braces into pre-located wall studs using a 3/32 in. diameter drill bit. Holes should come no closer than 2 in. from any inside edge.
3. Insert the installation screws into the holes and tighten securely. One screw should be located into each vertical brace.

Diagram shows drilling through cabinet back braces into wall studs.

Step 2: Wall Storage Cabinet Installation

(If applicable):

1. Using your level, position the cabinet on the wall at your desired location.
2. Drill through cabinet back into pre-located wall studs using a 3/32 in. diameter drill bit. One hole should be at the top of the cabinet and one near the bottom, no closer than 2 in. from any inside edge.
3. Insert the installation screws (included) into the holes and tighten securely.

Diagram shows a cabinet being mounted to a wall, indicating minimum distances from edges and maximum height. Dimensions: 2" Min., 12" Max.

Step 3: Linen Cabinet Installation

(If applicable):

1. Align the moulding top unit on top of the linen cabinet as shown. Insert the two 1 in. screws (included) through the two predrilled holes in the front end of the moulding top and into the linen cabinet and tighten securely.
2. Insert two 1/2 in. screws (included) through the "L" brackets, into the sides of the moulding top and tighten.
3. Insert two 1/2 in. screws (included) through the "L" brackets and screw into the top of the hutch cabinet.
4. Using your level, position the cabinet on the wall at your desired location.
5. Drill through cabinet back into pre-located wall studs using a 3/32 in. diameter drill bit. Both holes should be at the top of the cabinet to prevent tipping, no closer than 2 in. from any inside edge.
6. Insert the installation screws (included) into the holes and tighten securely.

Step 4: Mirror Installation

(If applicable):

1. Determine the desired location of the mirror.
2. Use appropriate screws or wall anchors (not provided) to hang mirror.
3. Be sure the hanging hardware is rated to handle the weight of the mirror. The mirror weight is approximately 25 lbs (11.34 kg).

Step 5: Base Storage Cabinet Installation

(If applicable):

1. Place wood top on vanity.
2. Affix top to vanity by tightening screws (included) through pilot holes into top.
3. Place your vanity base cabinet into the desired location.
4. Drill through cabinet back into pre-located wall stud using a 3/32 in. diameter drill bit. Hole should come no closer than 2 in. from any inside edge.
5. Insert the installation screw into the hole and tighten securely.

Diagram shows placing a wood top onto a vanity base cabinet and securing it with screws.

Step 6: Hinge Adjustment for Door Alignment

(If applicable):

Adjustments can be made for:

• Up and Down (Arriba y abajo / De haut en bas)
• Side to Side (De lado a lado / D'un côté à l'autre)
• In and Out (Adentro y afuera / Rentrée et sortie)

To lock: Press to lock. Diagram shows a clip being pressed to lock.

To remove: Pull back clip. Diagram shows a clip being pulled back to remove.

Step 7: Soft Close Hinge Damper

(If applicable):

To Adjust: Turn right for slower close, turn left for faster close.

Diagram shows a hinge damper with numbered parts: 1. Damper, 2. Adjustment screw, 3. Front Hinge Clips, 4. Back Clip.

Step 8: Vanity Drawer Removal

(If applicable):

1. Pull the drawer as far out as the slides allow. This will expose the latches (pointed black plastic).
2. Depress the latch and push the cabinet member back into the vanity. The right side latch must be pushed down and the left side must be pushed up.
3. Pull the drawer the rest of the way out.

Diagram illustrates the drawer removal process, showing how to depress latches on the slides (L for left, R for right) to release the drawer.