ZLINE Rubicon Bath Accessories
Installation and User Manual
Models: RBCN1-HK, RBCN1-TP, RBCN1-TRNG, RBCN1-TR, & RBCN1-TR18
Website: zlinekitchen.com
About ZLINE Kitchen and Bath
ZLINE Kitchen and Bath provides Attainable Luxury, where the kitchen and bath of your dreams is never out of reach. Through unique designs and unparalleled quality, ZLINE is dedicated to providing an elevated experience in the heart of your home. With an endless selection of features and finishes, their inspiration is your reality.
ZLINE is fueled by a passion for innovation; a relentless pursuit of bringing the highest end luxury designs and professional features into everyone's homes. ZLINE continually strives to improve its products and may change specifications and designs without prior notice.
Important Information
⚠️ WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
Before Installation
Parts Included
- Allen wrench
- Anchors
- Screws
Tools Needed
- Drill with 1/4" (6 mm) drill bit
- Flat head screwdriver
- Hammer
- Level
- Phillips head screwdriver
- Tape measure
Product Dimensions
RBCN1-HK (Robe Hook)
Description: SUS304 Robe Hook
Dimensions:
- Base: 2 3/16" x 2 3/16" (55 mm x 55 mm)
- Hook Projection: 3/8" (10 mm)
- Height (from base to top of hook): 1 3/16" (30 mm)
RBCN1-TP (Paper Holder)
Description: SUS304 Paper Holder
Dimensions:
- Base: 2 3/16" x 2 3/16" (55 mm x 55 mm)
- Bar Length: 6 7/8" (174 mm)
- Height (from base to top of bar): 1" (25 mm)
- Overall Depth: 3" (76 mm)
RBCN1-TRNG (Towel Ring)
Description: SUS304 Towel Ring
Dimensions:
- Base: 2 3/16" x 2 3/16" (55 mm x 55 mm)
- Ring Outer Diameter: 5 15/16" (151 mm)
- Ring Projection (from wall): 2 5/8" (67 mm)
- Overall Width: 6 15/16" (176 mm)
RBCN1-TR & RBCN1-TR18 (Towel Bar)
Description: SUS304 Towel Bar
Dimensions:
- Base: 2 3/16" x 2 3/16" (55 mm x 55 mm)
- Bar Length:
- RBCN1-TR18: 15 7/8" (403 mm)
- RBCN1-TR: 21 7/8" (556 mm)
- Overall Depth: 3" (76 mm)
Installation
Installation for RBCN1-HK, RBCN1-TP, & RBCN1-TRNG
Mark the installation area. Use a level to ensure the mounting hardware will be level. Drill Ø1/4" (Ø6 mm) holes for the mounting hardware.
[Diagram Description: Shows marking a wall, using a level, and drilling holes with a drill bit.]
Insert anchors into the drilled holes by gently tapping them with a hammer. Place screws through the mounting plate and thread them into the anchors.
[Diagram Description: Shows inserting anchors into wall holes and then attaching a mounting plate with screws.]
Place the accessory onto the mounting plate. Use an Allen wrench to tighten the set screw, securing the accessory to the mounting plate. Ensure the accessory is not installed upside down.
[Diagram Description: Shows attaching the accessory to the mounting plate and tightening a set screw.]
Installation for RBCN1-TR & RBCN1-TR18
Mark the installation area using a measuring tape and pencil. Ensure the markings are level. Then, drill Ø1/4" (Ø6 mm) holes for the mounting hardware.
[Diagram Description: Shows marking a wall with a tape measure and pencil, followed by drilling holes with a drill bit.]
Insert anchors into the drilled holes by gently tapping them with a hammer. Place screws through the mounting plate and thread them into the anchors.
[Diagram Description: Shows inserting anchors into wall holes and then attaching a mounting plate with screws.]
Place the accessory onto the mounting plate. Use an Allen wrench to tighten the set screw, securing the accessory to the mounting plate. Ensure the accessory is not installed upside down.
[Diagram Description: Shows attaching the accessory to the mounting plate and tightening a set screw.]
Care and Maintenance
To keep the product clean, follow these steps:
- Remove any surface dirt and film using clean water and a cotton cloth.
- Spray cleaner (such as mild liquid detergents, clear liquid glass cleaners, non-acidic and fully dissolved powder cleaners, or non-abrasive liquid polishers) onto a microfiber cloth to clean the product.
- Do not clean with soaps, acid, polish, abrasives, or harsh cleaners.
- Rinse the product with clean water to thoroughly remove cleaner and dry with a microfiber cloth.
Support and Parts
For questions, please contact the ZLINE Customer Service team at 1-614-777-5004 or visit www.zlinekitchen.com/contact to utilize the online Customer Experience Portal.
To view the most up-to-date version of this Installation Manual and User Manual, scan the QR code provided in the original document (or visit the ZLINE website).
Need to purchase a part or accessory for your ZLINE product? Visit www.zlineparts.com, ZLINE's official parts distribution partner.
