Baby Trend Nursery Center

Welcome

Thank you for choosing the Baby Trend Nursery Center. Please read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.

This manual provides detailed guidance for assembly, safe operation, and maintenance of your Nursery Center.

Contact Information:

If you experience any difficulty in using this product, please contact the Baby Trend Customer Service Department at 1-800-328-7363 between the hours of 8:00 A.M. and 4:30 P.M. Pacific Standard Time for assistance. Please have your model number and manufacturing date available when you call. This information can be found on a small sticker under the playard.

Contact by Mail: Baby Trend, Inc., 1607 S. Campus Ave., Ontario, CA 91761

Contact by Phone: 1-800-328-7363 (8:00am ~ 4:30pm PST)

Online: www.babytrend.com

Note: Toys and mobile may vary.

Important Safety Warnings

? WARNING: NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN. Infant may roll into space between pad and loose mesh side causing suffocation.

WARNING: Infants can suffocate:

• In gaps between a mattress too small or too thick and product sides
• On soft bedding

Never add a mattress, pillow, comforter, or padding. Use only the mattress provided by manufacturer. Never use a water mattress with this product.

See playard floor and side rails for warnings.

WARNING: Failure to follow these warnings and the instructions could result in serious injury or death.

General Safety Precautions:

• NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend Customer Service for replacement parts, repair or instructions. NEVER substitute parts.
• NEVER leave child in product with sides lowered. Be sure sides are in raised and locked position whenever child is in product.
• NEVER use plastic shipping bags or other plastic film as mattress covers not sold and intended for that purpose. They can cause suffocation.
• This product is not intended for commercial use.

Fall Hazard: To help prevent falls, do not use this product when the infant begins to push up on hands and knees or has reached the height of 25 in. (635 mm), weight of 15 lbs. (6.8 kgs) or 4 months old, whichever comes first.

Strangulation Hazard: NEVER place items with a string around a child's neck such as hood strings or pacifier cords. NEVER suspend strings over playard or attach strings to toys.

Discontinue use of the product when child is able to climb out or has reached the height of 35 in. (890 mm) or weight of 30 lbs. (14 kgs), whichever comes first.

When child is able to pull to standing position, remove bumper pads, large toys and other objects that could serve as steps for climbing out.

NEVER place product near a window where cords from blinds or drapes can strangle a child.

Always provide the supervision necessary for the continued safety of your child. When used for playing, NEVER leave child unattended.

To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician.

Use bassinet with only one child at a time.

NEVER place a child under the bassinet.

NEVER store the bassinet in the playard while in use.

The bassinet must be fully assembled and installed before using.

NEVER leave the changing table in place when the child is in the bassinet or the playard. Always flip changing table down while not in use.

To prevent your child from falls and other injuries, always use safety belt when child is on the changing table, always stay within arm's reach of your child when using the changing table.

To help prevent heat build-up inside the playard and to avoid overheating your child, when using the bassinet NEVER use an outdoor canopy.

Parts List

Check that you have all the below parts for this model before assembling the playard. (Note: This model may not include some features shown below.)

• Playard x 1
• Wheel x 2
• Wheel Axle x 2
• Retainer x 2
• Cap x 2
• Leg x 2
• Mattress x 1
• Bassinet x 1
• Metal Support Tubes (2 male, 2 female)
• Long Curved Bar x 2
• Short Bar with Connector Knob x 2
• Parent Organizer x 1
• Hook x 2
• Mobile Lower Arm x 1
• Mobile Arm Holder x 1
• Mobile Upper Curved Arm x 1
• Mobile Tri-shaped Arm x 1
• Toy Animal x 3
• Changing Table x 1
• Travel / Storage Bag x 1

Visuals showing individual parts are present in the original document.

Assembly Instructions

IMPORTANT: To ensure safe operation of your playard, please follow these instructions carefully. Please keep these instructions for future reference.

IMPORTANT: Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. NEVER use if any parts are missing or broken.

IMPORTANT: Adult assembly is required.

To Assemble Playard

Playard must be fully assembled and securely locked before installing or using other accessories.

1. Unzip bag and remove Playard frame. Undo the three (3) fastening straps and set the Mattress aside. (Visual: Diagram showing how to unzip the bag and remove the playard frame, and undoing fastening straps.)
2. Turn the Playard upside down.
3. Attach the Legs to the Playard by pushing each Leg into the bottom of the leg mount until both sides snap firmly into place. (Visual: Diagram showing how to attach a leg to the playard.) IMPORTANT: Check that each Leg is securely attached before use.
4. Attach the Wheels to the Playard using the axles, retainers and caps provided. Align each Wheel and insert axle through the center. Secure by pushing the retainer over the end of the axle until it snaps into place. Finish by pushing the cap over the end of the axle and retainer until it snaps into place. (Visual: Diagram illustrating the attachment of a wheel using an axle, and diagrams showing the placement of a retainer and cap on a wheel axle.) IMPORTANT: Check that each Wheel is securely attached before use.
5. Wheel Brakes: To operate the brakes on the Wheels, press downward on the brake levers. To release, lift upward on the lever. (Visual: Diagram illustrating how to operate the wheel brakes.)
6. Turn the Playard right side up and keep the Legs and Wheels close together. Stretch out the top of the Playard and pull up one side at a time of each of the top rails until each latch "Clicks" and locks securely into place. (Visual: Diagram showing how to raise and lock the top rails of the playard.) NOTE: The best way to lock the rail(s) is to hold one hand on each side and pull up sharply. (DO NOT pull from the middle where the latch release is located).
7. IMPORTANT: The handle located in the center of the Playard floor MUST remain raised (Approx. 45.7 cm or 18 inches) while locking the side rails in place. If the center is not raised, the rails will NOT lock. If you experience difficulty and one side of the rail will lock but the other side will not, unlock the rail by squeezing the release in the center and try again. If you still have difficulty, contact Customer Service.
8. Once all four (4) top rails are locked in place, push down on the center handle. The center mechanism will rotate clockwise 90 degrees and automatically lock in place. (Visual: Diagram showing the playard's center handle being pushed down to lock.) IMPORTANT: Test each top rail by pushing down slightly to confirm each is rigid and locked securely in place before use. (Visual: Diagram illustrating testing the rigidity of a locked top rail.)
9. Place the Mattress on the floor of the Playard with the padded side facing up. (Visual: Diagram showing the mattress being placed on the playard floor.)
10. Feed the three (3) hook and loop straps located on the underside of the Mattress through the slots in the floor of each end of the Playard. Fasten the hook and loop straps to the underside of the Playard floor to prevent the Mattress from moving. (Visual: Diagrams illustrating feeding mattress hook-and-loop straps through playard floor slots and fastening them.)

Folding Playard

1. Undo the three (3) hook and loop straps holding the Mattress from underneath the Playard floor or remove the Mattress for the Bassinet and set aside.
2. Grasp the center handle, push down and rotate the handle counter-clockwise 90 degrees and lift upward until the handle is as high as the top rails. Gather the Legs and Wheels together towards the center as close as possible so that they nearly touch. (Visual: Diagrams showing how to rotate the center handle for folding and gathering the legs and wheels.) NOTE: The top rails of the Playard are still in the "Locked" position.
3. Locate the rail release lever in the center and bottom side of each rail. Lift slightly while squeezing the lever until the rail "Clicks" and releases. Push down each side of the rail while still holding the release lever until both sides are down. Repeat for all remaining sides. (Visual: Diagram showing how to release a top rail using the lever.) NOTE: If the top rail(s) do not release completely, DO NOT FORCE! Check the floor of the Playard to make sure all the bottom rails are unlocked and make sure the middle handle is pulled up and has not fallen back down. If so, repeat step #3.
4. Gather four (4) corners and center all together tightly. (Visual: Diagram illustrating gathering the folded playard corners together.)
5. Wrap Mattress around Playard frame with padded side facing inward.
6. Secure the three (3) hook and loop straps by feeding them through the loops on the end of the Mattress and folding them back onto themselves. (Visual: Diagram showing how to secure the mattress around the folded playard frame with hook-and-loop straps.)
7. Place folded Playard into carry bag so that the handle comes through the opening between each side of the zipper.

To Assemble Bassinet

ATTENTION: Playard must be fully assembled and securely locked before installing or using the bassinet feature. You will need to remove the mattress from the bottom of the Playard to use inside your Bassinet.

1. Position the Bassinet over and down into the fully assembled Playard. Secure in place by pushing down firmly on each plastic support clip until all are snapped into place. (Visual: Diagram showing how to position and secure the bassinet into the playard.)
2. Assemble Mattress Support Tubes (if equipped; otherwise, skip to step 4) by inserting the two (2) male tubes into the two (2) female tubes. (Visual: Diagram illustrating the assembly of mattress support tubes.)
3. Insert both, assembled, Mattress Support Tubes into the loops provided on the bottom of the Bassinet. (Visual: Diagram showing the mattress support tubes being inserted into the bassinet loops.)
4. Place the Mattress into the Bassinet with the padded side facing upward. (Visual: Diagram showing the mattress being placed into the bassinet.) NOTE: Fasten tabs underneath the Mattress to secure it in place.

To Remove Bassinet:

1. Remove Mattress from Bassinet.
2. Remove Canopy.
3. Unsnap all clips and lift Bassinet.

To Assemble Changing Table

WARNING: FALL HAZARD: To prevent death or serious injury, always keep child within arm's reach. Always use restraint belt to prevent falls, see page 15 for details.

ATTENTION: Playard must be fully assembled and securely locked before installing or using the changing table feature.

Contents: 2 Long Curved Bars, 2 Short Bar with Connector Knobs, 1 Changing Table.

1. Connect the two (2) Long Curved Bars together. (Visual: Diagram showing two long curved bars being connected for the changing table.)
2. Insert the assembled curved bars into the Changing Table fabric. Slide the Curved Bars around inside the sleeve of the Changing Table. (Visual: Diagram illustrating inserting the assembled curved bars into the changing table fabric.)
3. Connect the two (2) Short Bars to each end of the Long Curved Bar. Make sure that the knobs are both facing down and the same direction on each end. (Visual: Diagrams showing short bars being connected to the long curved bars for the changing table, and the correct orientation of the connector knobs.)
4. Insert Connector Knob Prongs into holes located on both corners of the Playard. (Visual: Diagram showing the changing table connector knob prongs being inserted into playard holes.)
5. Turn the Connector Knobs counter clockwise to lock into place. (Visual: Diagram illustrating turning the connector knobs to lock the changing table.)
6. Flip Changing Table over onto Playard. (Visual: Diagram showing the changing table being flipped over onto the playard.)
7. Snap the two (2) buttons on the flap down onto the Playard. (Visual: Diagram illustrating snapping the changing table flap buttons onto the playard.)

IMPORTANT: Check that the Changing Table is correctly and securely installed BEFORE each use.

To use changing table restraint system:

1. Place child on changing table, make sure hand and arms are clear of the restraint. Bring the restraint around the child's waist and clip the male and female ends of the buckle together. (Visual: Diagram showing the changing table restraint system being applied around a child's waist.)
2. Tighten strap until it fits snug around child's waist. DO NOT OVER TIGHTEN. (Visual: Diagram illustrating tightening the changing table restraint strap.)
3. To remove, unsnap the buckle.

ATTENTION: NEVER use changing table if it is damaged or broken.

To remove changing table: Flip Changing Table to the outside of the Playard. Unsnap fabric flap of Changing Table from Playard. Twist Connector Knobs clockwise to unlock. Remove Changing Table from Playard and disconnect the Short Bars from the Curved Bar by pressing on the snap buttons and pulling apart. Remove Curved Bar from Changing Table sleeve.

Parent Organizer Assembly

For Parent Organizer: Position each hook so that the hooked end is facing the rear side of the organizer. Press the hook down firmly into the slot until it snaps into place. (Visual: Diagram showing how to attach the parent organizer hook.)

For Diaper Stacker: Skip to step 2.

Connect the Parent Organizer/Diaper Stacker to the Playard by sliding the two (2) connecting clips over an open portion of the top rail of the Playard. (Visual: Diagram illustrating connecting the parent organizer/diaper stacker clips to the playard top rail.) NOTE: The Parent Organizer/Diaper Stacker can only be installed on open sides of the Playard where the connecting clips can easily be attached without interfering with other features.

Mobile Assembly

ATTENTION: A crib mobile is intended for visual stimulation and is not intended to be grasped by the child. If attached to the crib or playpen, remove when baby begins to push up on hands and knees. If so designed, mount on wall or ceiling clearly out of a standing baby's reach. Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to a crib or playpen according to the instructions. Check frequently. DO NOT add additional strings and straps to attach to a crib or playpen. DO NOT attach the Mobile with child in Playard or Bassinet.

Contents: 1 Mobile Lower Arm, 1 Mobile Arm Holder, 1 Mobile Upper Curved Arm, 1 Mobile Tri-shaped Arm, 3 Toys (toys may vary).

1. Insert the Mobile Lower Arm into the Mobile Arm Holder until locked together. (Visual: Diagram showing the mobile's lower arm being inserted into the arm holder.)
2. Insert the Mobile Upper Curved Arm into the Mobile Lower Arm until locked together. (Visual: Diagram illustrating the upper curved arm being inserted into the lower arm.)
3. Snap the Mobile Tri-shaped Arm onto the end of the Upper Curved Arm. Connect each of the three Toys to the Mobile by threading the string into the slot at the end of each arm. (Visual: Diagram showing the tri-shaped arm being snapped onto the upper curved arm, and toys being attached.)
4. Insert the bottom of the Mobile Arm into the frame of the Playard. (Visual: Diagram illustrating the bottom of the mobile arm being inserted into the playard frame.)

Maintenance and Cleaning Instructions

Use only household mild soap and warm water.

DO NOT USE BLEACH.

DO NOT MACHINE WASH.