Important Information
IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
AVOID SCRATCHES! To avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
IMPROVE EFFICIENCY ! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
ANTI-TOPPLE WARNING ! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the anti-tip device provided. If not included, please purchase a wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
IMPORTANT ! It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product. For regular maintenance and cleaning, use a rag dipped in neutral detergent for the frame, then dry with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, as the board is easy to break.
Tools and Hardware Required
Please prepare the following tools:
[Illustration: A person pointing to a collection of tools including a tape measure, screwdrivers (Phillips and flathead), hammer, drill, and possibly a level.]
When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.
Hardware List:
- A: 33 pieces (Ø6 x 35 mm)
- B: 48 pieces (Ø3 x 12 mm)
- C: 33 pieces (Ø15 x 12 mm)
- D: 7 pieces (Ø3.5 x 25 mm)
- E: 1 piece
- F: 1 piece
- G: 1 piece
- H: 1 piece
- J: 4 pieces
- K: 6 pieces
- L: 8 pieces
- P: 4 pieces
- Q: 4 pieces
- R: 2 pieces
- N: 4 pieces
- O: 2 pieces (Ø6 x 30 mm)
Assembly Instructions
[Illustration: An exploded view diagram of the workstation, showing numbered parts 1 through 19, indicating assembly by 2 adults.]
WARNING: Children have died from furniture tipover. To reduce the risk of furniture tipover:
- ALWAYS install the anti-tip device provided.
- NEVER put a TV on this product.
- NEVER allow children to stand, climb, or hang on drawers, doors, or shelves.
- NEVER open more than one drawer at a time.
- Place heaviest items in the lowest drawers.
This is a permanent label. Do not remove!
Step 1
Screw eccentric rod (A) into the pre-drilled holes on boards 6 and 7 using a screwdriver. Ensure the rods are fully seated.
[Diagram: Shows board 6 and board 7 with multiple eccentric rods (A) being screwed in using a screwdriver.]
Step 2
Fix slide rail (F) and (E) to boards 6 and 7 using screw (B) as shown. Ensure the correct orientation (CR/CL) for the slide rails.
[Diagram: Shows boards 6 and 7 with slide rails (E, F) attached using screws (B). Close-up shows a screw (B) fastening a slide rail (E) to a board.]
Step 3
Attach board 8 to board 7. Insert cam lock (C) into the corresponding holes on board 8 and turn clockwise approximately 180 degrees to tighten.
[Diagram: Shows board 8 being attached to board 7. Close-up shows a cam lock (C) being inserted and turned to secure the connection.]
Step 4
Attach board 8 to board 6. Insert cam lock (C) into the corresponding holes on board 8 and turn clockwise approximately 180 degrees to tighten.
[Diagram: Shows board 8 being attached to board 6. Close-up shows a cam lock (C) being inserted and turned to secure the connection.]
Step 5
Screw eccentric rod (A) into board 16 using a screwdriver. Then, attach boards 6 and 7 to board 16. Insert cam lock (C) into the corresponding holes on boards 6 and 7 and turn clockwise approximately 180 degrees to tighten.
[Diagram: Shows board 16 with eccentric rods (A) screwed in. Then shows boards 6 and 7 being attached to board 16, with cam locks (C) being tightened.]
Step 6
Slide board 17 along the grooves provided in the assembled structure.
[Diagram: Shows the partially assembled unit, with board 17 being slid into place from the top.]
Step 7
Screw eccentric rod (A) into board 5 using a screwdriver.
[Diagram: Shows board 5 with eccentric rods (A) being screwed in.]
Step 8
Rotate foot (Q) and wheel (R) to the folding bed component (18) as shown.
[Diagram: Shows the folding bed component (18) with feet (Q) and wheels (R) being attached or adjusted.]
Step 9
Attach board 3 to the folding bed component (18) and fix it with screw (N) as shown.
[Diagram: Shows board 3 being attached to the folding bed component (18) and secured with screws (N). Close-up shows a screw (N) being inserted.]
Step 10
Screw eccentric rod (A) into boards 2 and 4 using a screwdriver.
[Diagram: Shows boards 2 and 4 with eccentric rods (A) being screwed in.]
Step 11
Attach boards 2 and 4 to board 3. Insert cam lock (C) into the corresponding holes on board 3 and turn clockwise approximately 180 degrees to tighten.
[Diagram: Shows boards 2 and 4 being attached to board 3, with cam locks (C) being tightened.]
Step 12
Screw eccentric rod (A) into board 1 using a screwdriver. Then, fix board 10 to board 1 using screw (D) as shown.
[Diagram: Shows board 1 with eccentric rods (A) screwed in. Then shows board 10 being attached to board 1 with screws (D). Close-up shows a screw (D) fastening board 10 to board 1.]
Step 13
Cover board 1 to the top of the component. Insert wooden dowel (O) into the holes. Add cam lock (C) into the holes in boards 2, 3, and 4, and turn clockwise approximately 180 degrees to tighten.
[Diagram: Shows board 1 being placed on top. Dowels (O) are inserted. Cam locks (C) are tightened in boards 2, 3, 4.]
Step 14
Cover board 5 to the top of the component. Add cam lock (C) into the holes in boards 6 and 7, and turn clockwise approximately 180 degrees to tighten.
[Diagram: Shows board 5 being placed on top. Cam locks (C) are tightened in boards 6 and 7.]
Step 15
Fix handle (J) to boards 9 and 19 using screw (L) as shown. Fix hinge (K) to boards 19 and 9 using screw (B) as shown.
[Diagram: Shows handles (J) being attached to doors (9, 19) with screws (L). Shows hinges (K) being attached to doors (19, 9) with screws (B). Close-ups show the fastening process.]
Step 16
Assemble doors 9 and 19 to the cabinet by fixing the hinges with screw (B) as shown.
[Diagram: Shows doors 9 and 19 being attached to the main cabinet structure using hinges and screws (B).]
Step 17
Fix handle (J) to board 15 using screw (L) as shown. Screw eccentric rod (A) into board 15 using a screwdriver.
[Diagram: Shows board 15 with a handle (J) attached by screws (L) and eccentric rods (A) screwed in.]
Step 18
Fix boards 12 and 13 to board 11 using screw (D) as shown. Insert board 14 along the grooves.
[Diagram: Shows boards 12 and 13 being attached to board 11 with screws (D). Board 14 is shown being slid into place.]
Step 19
Attach board 15 to boards 12 and 13. Add cam lock (C) and turn clockwise approximately 180 degrees to tighten.
[Diagram: Shows board 15 being attached to boards 12 and 13, with cam locks (C) being tightened.]
Step 20
Fix runner (G) and (H) to boards 13 and 12 using screw (B) as shown.
[Diagram: Shows runners (G, H) being attached to boards 13 and 12 with screws (B). Close-up shows a screw (B) fastening a runner (G) to a board.]
Step 21
[Diagram: Shows the completed workstation assembly, with drawers and doors in place.]
No specific textual instruction provided for this step, likely a visual confirmation of the assembled unit.
Step 22
Insert buckle (P) into the back slots and fix with screw (B) as shown.
[Diagram: Shows buckles (P) being inserted into rear slots and secured with screws (B).]
Warranty Information
WARRANTY CLAIMS
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
- Before making a claim, please call to inquire. Provide your purchase order number and details of the problem for replacement parts. A response will be arranged within 48 hours. If a part is out of stock, a shipping date will be provided.
- The product must be used in accordance with the provided instructions.
- For other reasons, if the furniture needs to be returned, it must be cleaned and dried and returned within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty.
- Damage during installation is not covered, but damage during transportation is.
Scope of Responsibility
- The manufacturer shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
- Damage and scratches occurring after use are not covered by the warranty.
Warranty Coverage Areas (USA)
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns Policy
CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?
If you have purchased and simply changed your mind, follow the retailer's instructions for returns.
DEFECTIVE ITEMS
If your item is defective in any way, meaning it doesn't work but you cannot identify why, please call for assistance in the first instance.
DAMAGED ITEMS
If you receive an order with obvious shipping damage from the retailer, it is suggested that the delivery is refused. If the delivery has been accepted and shipping damage is subsequently found, please follow the specific instructions advised by the retailer.
In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardize your chances of making a claim, and you may not receive credit for the return.
AFTER-SALES CONTACT
- Email: feedbackstation@163.com
- Phone: (303)800-6387
