Honda Installation Instructions
Accessory: PANNIER PANEL KIT (ALUMINUM)
P/N: 08L80-MKT-D00
Application: NC750XA/XD
Publication No.: MII 17714
Issue Date: April 2021
Honda Dealer: Please give a copy of these instructions to your customer.
Parts List
| No. | Description | Qty |
|---|---|---|
| [part 1] | Installation instructions | 1 |
| [part 2] | Right pannier panel | 1 |
| [part 3] | Left pannier panel | 1 |
Diagram description: Shows the left pannier panel, labeled [part 2] Right pannier panel and [part 3] Left pannier panel.
Pannier Case
Sold separately
| No. | Description | Qty |
|---|---|---|
| [part 1] | Installation instructions | 1 |
| [part 2] | Right pannier case | 1 |
| [part 3] | Left pannier case | 1 |
Diagram description: Shows the pannier case, labeled [part 2] Right pannier case and [part 3] Left pannier case.
Tools and Supplies Required
- Hex wrench (3 mm)
- Isopropyl alcohol
- Shop towel
- Torque wrench
Torque Chart
Tighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts.
| Item | N·m | kgf·m | lbf·ft |
|---|---|---|---|
| Screw | 4.2 | 0.4 | 3.1 |
Installation
Notes:
- Heat the bonding surfaces with a hair dryer if the ambient air temperature is below 70°F (21°C).
- The adhesive reaches full strength in 72 hours. Wait at least 24 hours before riding your motorcycle.
Step 1: Prepare the Left Pannier Case Lid
Open the left pannier case lid. Remove the necessary parts as shown in the diagram. These parts include the O-RING, LID NUT, WASHER [save], and SCREW.
Diagram description: Shows the left pannier case lid with components labeled LID NUT, O-RING, WASHER [save], and SCREW, with arrows indicating their positions for removal/preparation.
Step 2: Clean the Surface
To maintain the adhesive strength of the double-sided tape, clean the surface of the indicated area on the left pannier case with isopropyl alcohol.
Diagram description: Illustrates cleaning the surface of the left pannier case with a bottle of ISOPROPYL ALCOHOL.
Step 3: Peel Adhesive Backing
Peel off the adhesive backing on the left pannier panel as shown. Peel back the backing, leaving a small portion adhered to facilitate handling.
Diagram description: Shows the left pannier panel with ADHESIVE BACKING being peeled back.
Step 4: Attach Left Pannier Panel
Align the left pannier panel with the shape of the left pannier case lid and attach it.
Diagram description: Shows the left pannier panel being aligned and attached to the left pannier case lid.
Step 5: Check Alignment
Temporarily set the screw and check that there is no misalignment. If there is a misalignment, start over from step 4.
Diagram description: Shows a SCREW [reuse] being temporarily set.
Step 6: Secure the Panel
Remove the remaining adhesive backings while pressing firmly on the top box lid panel with your palm.
Diagram description: Shows ADHESIVE BACKING being pulled out while pressing the left pannier panel onto the case lid.
Step 7: Apply Pressure
Apply adequate pressure of 5kgf (50N) to the attached pannier case panel. Ensure to crimp with a force of 5 kgf (50 N).
Diagram description: Shows arrows indicating the application of adequate pressure of 5kgf (50N) to the attached pannier case panel.
Step 8: Allow Adhesive to Stabilize
Leave the pannier case panel for 10 minutes to stabilize the fitting of the adhesive surface.
Step 9: Install Remaining Parts
Install the remaining parts as shown. This includes the O-RING [reuse], LID NUT [reuse], and SCREW [reuse] onto the left pannier case.
Diagram description: Shows the O-RING [reuse], LID NUT [reuse], and SCREW [reuse] being installed onto the left pannier case.
Step 10: Install Right Pannier Panel
Install the right pannier panel in the same manner as the left side.
