Honda CB650R/RA Front Visor Installation Instructions
Publication No. MII 17050 | Issue Date: March 2019
Parts List
| No. | Description | Qty |
|---|---|---|
| (1) | Installation Instruction URL | 1 |
| (2) | Front visor | 1 |
| (3) | 5 mm bolt | 4 |
| (4) | Washer (White) | 4 |
| (5) | Well nut | 4 |
| (6) | Washer (Black) | 4 |
Diagram Description: The parts list shows the front visor (a curved shield) and its associated hardware: four 5 mm bolts, four white washers, four well nuts, and four black washers. Item (1) is the installation instruction document.
Visor Stay (Sold Separately)
| No. | Description | Qty |
|---|---|---|
| (1) | Installation Instruction URL | 1 |
| (2) | Right visor stay | 1 |
| (3) | Left visor stay | 1 |
Diagram Description: The visor stay parts list shows two brackets, labeled as the Right visor stay (2) and Left visor stay (3), along with an installation instruction document (1).
Tools and Supply Required
- Hex wrench (3 mm)
- Ruler
- Torque wrench
Torque Chart
| Item | N·m | kgf·m | lbf·ft |
|---|---|---|---|
| 5 mm bolt | 0.4 | 0.04 | 0.3 |
Note: Tighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of removed parts.
Installation
⚠️ CAUTION: To prevent burns, allow the engine, exhaust system, radiator, etc., to cool before installing the accessory.
[Note]:
- Disconnect the negative (-) cable from the battery before installing this accessory.
- The clock memory will be erased when you disconnect the battery. Reset the clock after reconnecting the battery.
- Reinstall the removed parts on the motorcycle and make sure that the wires and harnesses are not pinched.
Step 1: Remove the passenger seat.
Diagram Description: Illustrates the removal of the passenger seat from the motorcycle.
Step 2: Remove the main seat and disconnect the negative (-) cable of the battery.
Diagram Description: Shows the main seat removed, exposing the battery. A bolt and collar are depicted near the battery terminal, indicating the disconnection of the negative battery cable.
Step 3: Remove the bolt as shown. Repeat on the right side.
Diagram Description: Depicts the removal of a bolt from the left side of the motorcycle frame, near the headlight mounting area. The instruction specifies repeating this action on the right side.
Step 4: Remove the headlight as shown. Disconnect the connector.
Diagram Description: Shows the headlight assembly being detached from the motorcycle. A connector is shown being unplugged from the headlight.
Step 5: Remove the collars as shown.
Diagram Description: Illustrates the removal of collars from the headlight mounting points.
Step 6: Remove the bolts as shown.
Diagram Description: Depicts the removal of bolts securing the headlight assembly.
Step 7: Loosely install the left visor stay as shown. Repeat on the right side.
Diagram Description: Shows the left visor stay being loosely attached to the motorcycle frame using a bolt and a reused collar. The instruction indicates repeating this process on the right side.
Step 8: Loosely install the bolt as shown. Repeat on the right side.
Diagram Description: Illustrates the loose installation of a bolt, likely for the visor stay mounting. The instruction specifies repeating on the right side and reusing bolts.
Step 9: Securely tighten the bolt as shown. Repeat on the right side.
Diagram Description: Shows the bolt installed in Step 8 being securely tightened. The instruction indicates repeating this on the right side.
Step 10: Remove the bolt and collar as shown. Repeat on the right side.
Diagram Description: Depicts the removal of a bolt and collar from the headlight mounting area, with instructions to repeat on the right side.
Step 11: Install the collars to the headlight in the reverse order of removal.
Diagram Description: Textual instruction to install the headlight collars in the reverse order of their removal.
Step 12: Install the headlight in the reverse order of removal.
Diagram Description: Textual instruction to install the headlight assembly back onto the motorcycle in the reverse order of its removal.
Step 13: Install the bolt as shown. Repeat on the right side.
Diagram Description: Shows a bolt being installed, likely to secure the reinstalled headlight assembly. The instruction indicates repeating this on the right side.
Step 14: Install the well nuts as shown. Repeat on the right side.
Diagram Description: Depicts the installation of well nuts into mounting points on the motorcycle frame, with a bolt ready for insertion. The instruction specifies repeating this on the right side.
Step 15: Install the front visor as shown. Tighten the 5 mm bolts as shown.
Diagram Description: Shows the front visor being attached to the visor stays using 5 mm bolts, black washers, white washers, and well nuts. A section view details the assembly order and specifies a gap of 1.5-2.5 mm between the visor and the mounting point.
Step 16: Install the motorcycle's parts in the reverse order of removal. Confirm that any wire harness is not caught or too tight.
Diagram Description: Textual instruction to reinstall all motorcycle parts in the reverse order of their removal, ensuring that no wire harnesses are pinched or excessively tight.
©2019 American Honda Motor Co., Inc. All Rights Reserved.
