Parts List
| No. | Description | Qty |
|---|---|---|
| (1) | Passenger seat | 1 |
| (2) | 8 mm socket bolt (short) | 1 |
| (3) | Roll pin | 1 |
| (4) | Left peg holder | 1 |
| (5) | 8 mm socket bolt (long) | 2 |
| (6) | Right foot peg | 1 |
| (7) | Left foot peg | 1 |
| (8) | Joint pin | 2 |
| (9) | Click plate | 2 |
| (10) | Spring | 2 |
| (11) | Steel ball | 2 |
| (12) | 8 mm washer (thin) | 2 |
| (13) | Split pin | 2 |
| (14) | Peg bracket | 1 |
| (15) | Peg bracket bolt | 1 |
| (16) | 8 mm flange bolt | 1 |
| (17) | 8 mm washer (medium) | 1 |
| (18) | 8 mm washer (thick) | 1 |
| (19) | Collar | 1 |
| (20) | 10 mm self-lock nut | 1 |
| (21) | Installation Instruction URL | 1 |
Diagram showing various parts labeled with numbers (1-21) corresponding to the parts list, including the passenger seat, foot pegs, brackets, bolts, washers, springs, and pins.
Tools and Supply Required
- Socket (12 mm)
- Ratchet
- Box-end wrench (17 mm)
- Hex wrench (6 mm)
- Long nose pliers
- Plastic hammer
- Grease
- Torque wrench
Torque Chart
Tighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts.
| Item | N·m | kgf·m | lbf·ft |
|---|---|---|---|
| 8 mm socket bolt (short) | 22 | 2.2 | 16 |
| 8 mm socket bolt (long) | 33 | 3.3 | 24 |
| 8 mm flange bolt | 27 | 2.8 | 20 |
| 10 mm self-lock nut | 39 | 4.0 | 29 |
User Safety
Do not carry a passenger unless a passenger seat with grab strap and foot pegs have been securely installed on your motorcycle.
WARNING
Carrying a passenger without a properly designed and installed passenger seat and foot pegs can result in serious injury or death to you and/or the passenger.
Never carry a passenger without first installing a passenger seat (with grab strap) and foot pegs specifically designed for this motorcycle. Further, never carry more than one passenger.
Installation
CAUTION
To prevent burns, allow the engine, exhaust system, radiator, etc. to cool before installing the accessory.
NOTE
Take care not to damage the painted surfaces of the motorcycle.
- Refer to the Service Manual for the motorcycle, remove the bolts as shown.
Diagram illustrating the removal of bolts from the motorcycle frame, with labels 'BOLTS (Save)' and 'BOLT (Save)'.
- Install the collar, 8 mm medium washer and bolt as shown.
Diagram showing the installation of a collar, an 8 mm medium washer, and an 8 mm flange bolt.
- Install the hardware and passenger seat as shown.
Diagram illustrating the installation of the passenger seat using an 8 mm socket bolt (short) and an 8 mm washer (thick).
- Install the peg bracket bolt as shown.
Diagram showing a peg bracket bolt being inserted into a peg bracket.
- Assemble the right passenger peg as shown. Apply grease to the indicated areas. ?️
Diagram detailing the assembly of the right passenger peg, including the right foot peg, peg bracket, spring, steel ball, click plate, joint pin, and split pin. A close-up shows a split pin securing the joint pin.
- Install the right passenger peg assembly as shown. Tighten the 10 mm self-lock nut securely. ✔️
Diagram showing the installation of the assembled right passenger peg onto the motorcycle frame, secured by a 10 mm self-lock nut. A close-up shows a roll pin being press-fit into the peg bracket bolt. ➡️
- Install the left passenger peg to the left peg holder as shown. Apply grease to the indicated areas. ?️
Diagram detailing the assembly of the left passenger peg, including the left foot peg, left peg holder, spring, steel ball, click plate, joint pin, and split pin. A close-up shows a split pin securing the joint pin.
- Install the left passenger peg holder assembly as shown.
Diagram showing the installation of the left passenger peg holder assembly onto the motorcycle frame using an 8 mm socket bolt (long).
