Pure & Easy Bathroom Vanity Assembly Instructions
Model Numbers: FTBRBC-7001, FTBRBC-7011
Important Notices & Safety
NOTICE: IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
Assembly Environment: Assemble on a flat, clean, and soft surface.
Installation Recommendation: Professional installation is highly recommended.
Maintenance: Periodically check that all components are tightly secured.
Tip-Over Hazard: Serious or fatal crushing injuries can occur from furniture tip-over. Always secure this furniture to the wall using tip-over restraints. [⚠️]
Child Safety: Never let children climb or hang on drawers, doors, or shelves. [??♂️]
Assembly Requirements
Teamwork: It is recommended that multiple people assemble this product.
Required Tools: Please have the following auxiliary tools ready:
- Drill [?]
- Screwdriver [?]
- Hammer [?]
- Wrench [?]
- Measuring Tape [?]
- Level [?]
- Safety Helmet [⛑️]
Assembly Guide
Section 1: Cam Lock and QuickFit Mechanism
QuickFit Tightening: Tighten the QuickFit until its shoulder is flush with the panel. Do not overtighten or undertighten.
Cam Lock Installation: When fitting the cam lock, ensure the starting position is correct before inserting the connecting QuickFit. The QuickFit head should be in the center of the cam lock when the two panels are joined. The cam lock should be inserted before the QuickFit. Turn the cam lock clockwise to tighten.
Section 2: Drawer Slides Preparation
Preparation: Slides must be separated before assembly. After separation, set aside until needed.
Step 1: Extend Slide
Step 2: Push Lever UP
Step 3: Remove Runner
Important Note: Pay attention when connecting! The sliding module must be at the front end. [⚠️]
Section 3: Exploded View and Parts Identification
The following diagram illustrates an exploded view of the product components, showing how they fit together:
[Diagram Description: The exploded view shows the main cabinet structure. Key components include side panels (1, 2), base shelf (3), drawer support (4), horizontal supports (5, 6), back panel support (7), shelf support (8), doors (9, 10), and the sink/countertop unit (11). Hardware such as mounting brackets (M) and legs (F) are also depicted.]
Parts List:
| Item No. | Reference Image Description | Quantity |
|---|---|---|
| 1 | Left Side Panel | x1 |
| 2 | Right Side Panel | x1 |
| 3 | Base Shelf | x1 |
| 4 | Drawer Support Rail | x1 |
| 5 | Lower Horizontal Support | x1 |
| 6 | Upper Horizontal Support | x1 |
| 7 | Back Panel Support | x1 |
| 8 | Middle Shelf Support | x1 |
| 9 | Left Door | x1 |
| 10 | Right Door | x1 |
| 11 | Sink and Countertop Unit | x1 |
Hardware List:
| Item No. | Reference Image Description | Quantity |
|---|---|---|
| A | Screw (Ø6x33mm) | x24 |
| B | Screw (Ø14.5x9.5mm) | x24 |
| C | Screw (Ø8x30mm) | x20 |
| D | Hinge Assembly | x4 |
| E | Hinge Screw | x24 |
| F | Cabinet Leg/Foot | x4 |
| G | Cam Lock Nut | x16 |
| H | Cam Lock Bolt | x16 |
| I | Cam Lock Bolt | x16 |
| J | Screw | x2 |
| K | Screw | x2 |
| L | Screw | x2 |
| M | Drawer Slide Mounting Bracket | x2 |
| N | Drawer Slide Screw | x10 |
| O | Drain Assembly | x1 |
| P | Faucet Assembly | x1 |
| Q | Sink Mounting Screw | x2 |
| R | Sink Securing Clip/Washer | x8 |
Step-by-Step Assembly:
Step 1: Attach side panels (1, 2) and base shelf (3) to the back panel support (7) using 24 x Screw (A).
Step 2: Assemble the main cabinet structure. Attach horizontal supports (5, 6) and drawer support (4) to the side panels (1, 3) using Screws (A) and (B).
Step 3: Install mounting brackets (M) and legs (F) using hardware (G, H, I, J, K, L, P). Attach shelf support (8) using appropriate hardware.
Step 4: Attach doors (9, 10) to the cabinet using hinges (D) and screws (E). Detailed diagrams show how to adjust the doors using specific screws for vertical (up/down), horizontal (left/right), and depth (in/out) positioning.
Step 5: Install the sink/countertop unit (11). Secure it to the cabinet top using screws (K, Q). The unit dimensions are approximately 780mm in height and 507mm in width.
Step 6: Install the drain assembly (O) and faucet assembly (P) into the sink. Secure the sink unit to the cabinet using securing clips/washers (R). Tip: Consumers can also choose to use neutral glass glue to fix ceramic basins and bathroom cabinets.
Step 7: Installation Completed. [✔️]
Help Center & Disclaimer
Help Center: If you encounter any difficulties during assembly, please contact us.
Disclaimer: Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.
