Pure & Easy Assembly Instructions
Model: FTBRBC-7005
Important Notices and Safety Information
NOTICE: IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
Assemble on a flat, clean, and soft surface. [person assembling]
Professional installation is highly recommended. [professional installation recommended]
Periodically check that all components are tightly secured. [check components]
Serious or fatal crushing injuries can occur from furniture tip-over. Always secure this furniture to the wall using tip-over restraints. [warning: tip-over hazard] [secure furniture to wall]
Never let children climb or hang on drawers, doors, or shelves. [warning: do not let children climb]
Preparation and Tools
It is recommended that multiple people assemble this product. [multiple people recommended]
Please have the following auxiliary tools ready:
- [power drill]
- [screwdriver]
- [wrench]
- [tape measure]
- [spirit level]
- [hammer]
- [safety helmet]
Drawer Slide Separation
Slides must be separated before assembly. After separation, set aside until needed for assembly.
Step 1: Extend Slide.
Step 2: Push Lever UP.
Step 3: Remove Runner.
Pay attention when connecting: The sliding module must be at the front end. [sliding module at front end]
Push lever for the left of drawer, press the lever for the right of drawer.
Using Cam Lock and QuickFit
Tighten QuickFit until the shoulder is flush with the panel. Do not overtighten or undertighten. [tighten QuickFit]
When fitting the cam lock, ensure the starting position is correct before inserting the connecting QuickFit.
The QuickFit head should be in the center of the cam lock when the two panels are joined. The cam lock should be inserted before the QuickFit. Turn the cam lock clockwise to tighten. [insert cam lock] [turn clockwise]
Parts List
Numbered Parts (1-23)
| Item No. | Reference Image | Qty. |
|---|---|---|
| 1 | [Side Panel] | x1 |
| 2 | [Side Panel] | x1 |
| 3 | [Bottom Panel] | x1 |
| 4 | [Back Panel] | x1 |
| 5 | [Shelf] | x1 |
| 6 | [Top Panel] | x1 |
| 7 | [Back Support] | x1 |
| 8 | [Hinge Plate] | x1 |
| 9 | [Drawer Front] | x1 |
| 10 | [Drawer Side] | x1 |
| 11 | [Drawer Runner] | x2 |
| 12 | [Drawer Bottom] | x1 |
| 13 | [Drawer Back] | x1 |
| 14 | [Drawer Front Support] | x1 |
| 15 | [Drawer Slide Component] | x2 |
| 16 | [Drawer Slide Component] | x1 |
| 17 | [Drawer Slide Component] | x1 |
| 18 | [Drawer Slide Component] | x1 |
| 19 | [Drawer Slide Component] | x1 |
| 20 | [Drawer Slide Component] | x1 |
| 21 | [Drawer Slide Component] | x1 |
| 22 | [Drawer Slide Component] | x1 |
| 23 | [Sink Unit] | x1 |
Lettered Parts (A-R)
| Item No. | Reference Image | Qty. |
|---|---|---|
| A | [Ø6x33mm Screw] | x51 |
| B | [Ø14.5x9.5mm Screw] | x51 |
| C | [Ø8x30mm Screw] | x15 |
| D1 | [Drawer Slide Part 1] | x4 |
| D2 | [Drawer Slide Part 2] | x4 |
| E | [Cam Lock Screw] | x24 |
| F | [Hinge] | x2 |
| G | [Handle Screw] | x12 |
| H | [Handle] | x3 |
| I | [Handle Screw] | x6 |
| J | [Faucet Assembly] | x1 |
| K | [Mounting Screw] | x2 |
| L | [Wall Anchor Screw] | x2 |
| M | [Washer] | x2 |
| N | [Mounting Bracket] | x2 |
| O | [Shelf Support Pin] | x12 |
| P | [Drain Assembly] | x1 |
| Q | [Wall Screw] | x2 |
| R | [Sink Seal/Gasket] | x8 |
Assembly Steps
Step 1: Assemble Main Cabinet Frame
Connect side panels (1, 2), bottom panel (3), back panel (4), and other frame components using screws (A, B) and cam locks (E). Ensure all connections are secure and panels are correctly oriented as per the diagrams.
Step 2: Attach Drawer Slides to Cabinet Sides
Mount the cabinet members of the drawer slides (D1, D2) to the inside of the side panels (1, 4). Use screws (E) and ensure correct placement and orientation as indicated by "REAR" and "POSITION OF SCSEW" guides.
Step 3: Assemble Drawer Boxes
Construct the drawer boxes by connecting drawer sides, front, back, and bottom panels (e.g., 5, 9, 10, 12, 13) using screws (B, C) and cam locks (E). Attach drawer runners (11) to the drawer sides.
Step 4: Install Hinges and Handles
Attach hinges (F) to the cabinet doors/sides using screws (K). Mount handles (H) onto the drawer fronts (9) using handle screws (G, I). Use mounting brackets (N) and other hardware as shown.
Step 5: Insert Drawers into Cabinet
Slide the assembled drawer boxes into the cabinet runners. Ensure smooth operation. Use appropriate screws (B, C, E) and hardware as indicated.
Step 6: Attach Drawer Fronts and Final Cabinet Assembly
Secure the drawer fronts to the assembled drawer boxes. Attach any remaining panels or supports (e.g., 6, 7, 14, 15, 16, 17, 18, 19, 20, 21, 22) using the specified hardware (B, C, E, H). Ensure all parts are flush and secure.
Step 7: Wall Mounting
Secure the vanity unit to the wall. For stud walls, locate studs and use appropriate screws. For concrete walls, drill holes, insert anchors, and use screws. Use mounting hardware (K, L, M, Q) for wall attachment. Ensure the unit is level and stable. [Diagram showing wall mounting with studs and concrete options]
WARNING: INSTALLATION METHOD OF FLOATING VANITY HAS BIG RELATION WITH THE WALL STRUCTURE. To get the best installing effect, please follow as below: Please screw through the "L" shape hanger if there is exactly wall stub behind the hanger.
Step 8: Sink and Faucet Installation
Install the sink basin (23) and faucet assembly (J). Secure the sink using seals or glue (R) and the drain assembly (P). Connect plumbing as required.
Tip: Consumers can also choose to use neutral glass glue to fix ceramic basins and bathroom cabinets.
Step 9: Installation Completed
The vanity installation is complete. Verify all components are securely fastened and the unit is stable.
Help Center and Disclaimer
HELP CENTER: If you encounter any difficulties during assembly, please contact us for assistance.
DISCLAIMER: Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.
