NOTICE
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
Illustration shows a person assembling furniture on a flat, clean, and soft surface. Another illustration shows a piece of furniture being secured to a wall.
Assemble on a flat, clean and soft surface.
Professional installation is highly recommended.
Periodically Check That All Components Are Tightly Secured.
Safety Warnings
It is recommended that multiple people assemble this product.
Please have the following auxiliary tools ready: [power drill], [hammer], [screwdriver], [tape measure], [utility knife], [safety helmet].
Serious or fatal crushing injuries can occur from furniture tip-over. Always secure this furniture to the wall using tip-over restraints.
Never let children climb or hang on drawers, doors, or shelves.
Preparation
Press And Hold The Drawer Runner Lock And Then Continue To Slide Drawer Runners Apart Before Installation.
Using Cam Lock and QuickFit
Tighten QuickFit until the shoulder is flush with the panel. Do not overtighten or under tighten.
When fitting the cam lock, ensure the starting position is correct before inserting the connecting QuickFit.
The QuickFit head should be in the center of the cam lock when the two panels are joined. The cam lock should be inserted before the QuickFit. Turn the cam lock clockwise to tighten.
Parts List
| Item No. | Reference Image Description | Qty. |
|---|---|---|
| 1 | Left side panel (with drawer slides) | X1 |
| 2 | Right side panel (with drawer slides) | X1 |
| 3 | Back panel (tall, narrow) | X1 |
| 4 | Bottom panel | X1 |
| 5 | Drawer runner (long, thin) | X1 |
| 6 | Top panel | X1 |
| 7 | Shelf (long, narrow) | X1 |
| 8 | Drawer front panel | X1 |
| 9 | Drawer side panel (left) | X1 |
| 10 | Drawer side panel (right) | X1 |
| 11 | Drawer bottom panel | X3 |
| 12 | Drawer runner (short) | X3 |
| 13 | Drawer back panel | X3 |
| 14 | Drawer side panel (with groove) | X3 |
| 15 | Drawer bottom panel (thin) | X3 |
| 16 | Door panel | X3 |
| 17 | Leg/Foot | X1 |
| A | Countertop/Sink unit | X1 |
| B | Screw (M8 x 30mm) | X23 |
| C | Screw (M6 x 34mm) | X50 |
| D | Cam lock (Ø15 x 9mm) | X50 |
| E | Screw (ST4 x 25mm) | X4 |
| F | Screw (ST4 x 28mm) | X12 |
| G | Screw (ST3.5 x 15mm) | X24 |
| H | Screw (ST3.5 x 12mm) | X2 |
| I | Screw (Ø5/32 x 12mm) | X3 |
| J | Screw (Ø5/32 x 25mm) | X2 |
| K | Hinge part | X5 |
| L | Hinge assembly | X4 |
| M | Drawer slide bracket | X1 |
| N | Drain assembly part | X1 |
| O | Drain pipe | X1 |
| P | Screw (Ø8 x 20mm) | X2 |
| Q | Wall mounting bracket and screws (A1x2, A2x1, A3x1, A4x1) | X1 set |
Exploded View
An exploded view of the vanity cabinet showing all major components (1-17, A) and their relative positions before assembly.
Assembly Steps
Step 1
Attach panel 6 to panel 3 using 14 screws (C). Attach panel 4 to panel 3 using screws (C). Attach drawer runner 5 to panel 4 using screws (C).
Step 2
Attach panel 6 to panel 3 using 3 screws (B) and 5 cam locks (D). Attach panel 7 to panel 4 using screws (B) and cam locks (D).
Step 3
Connect panel 6 to panel 3 using screws (B) and cam locks (D). Connect panel 5 to panel 3 using screws (B) and cam locks (D). Connect panel 7 to panel 4 using screws (B) and cam locks (D). Connect panel 11 to panel 7 using screws (B) and cam locks (D). Connect panel 6 to panel 7 using screws (B) and cam locks (D).
Step 4
Attach panel 2 to panel 1 using 24 screws (C). Attach panel 1 to panel 2 using screws (C).
Step 5
Assemble drawer components. Attach drawer sides (3, 7) to drawer back (13) and drawer bottom (11) using screws (B) and cam locks (D). Attach drawer runner (5) to drawer side (3) and drawer runner (11) to drawer side (7).
Step 6
Attach back panel (8) to the assembled cabinet frame using screws (B) and cam locks (D). Attach drawer runners (2) to the cabinet sides (3, 7).
Step 7
Attach the countertop (A) to the cabinet frame. Secure the countertop using screws (B), cam locks (D), screws (E), and screws (P). Attach wall mounting bracket (Q) to the cabinet.
Step 8
Assemble drawers. Attach drawer sides (13, 14) to drawer back (15) and drawer bottom (12) using screws (F) and cam locks (D). Attach drawer front (16) to the drawer assembly using screws (C) and cam locks (D). Attach drawer slides (12, 13) to the drawer sides.
Step 9
Install drawer slides (L) onto the drawer sides (9, 10) using screws (G).
Step 10
Attach doors. Mount hinges (K) to the doors (9, 10) using screws (G). Attach hinges to the cabinet frame using screws (G).
Step 11
Attach drawer handles/knobs (M) to the drawer fronts (16) using screws (H).
Step 12
Install drain assembly (N) into the sink on countertop (A).
Step 13
Connect drain pipe (O) to the drain assembly (N).
Step 14
Place the assembled countertop unit (A) onto the cabinet base.
Step 15
Secure the countertop unit to the cabinet using wall mounting hardware (Q). Attach wall mounting bracket (A1, A2, A3, A4) to the wall and the unit.
Step 16
Installation Completed.
Help Center
If you encounter any difficulties during assembly, please contact us.
Disclaimer
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.
