NITHO ZEGRAD RGB GAMING DESK

Components

Please check you have all the pieces listed below:

• Hardware:
  • [M4x14 screw] (x36)
  • [M8x16 screw] (x8)
  • [M8 nut] (x2)
  • [N-type foot] (x4)
  • [6mm Allen key] (x1)
• Parts:
  • Part A: Desk Legs (x2) - Z-shaped metal legs.
  • Part B: Crossbars (x2) - Horizontal metal bars for frame support.
  • Part C1: Support Bracket (x1) - Angled metal bracket.
  • Part C2: Support Bracket (x1) - Angled metal bracket.
  • Part D: Desktop (x1) - The main desk surface.
  • Part E: Cable Management Clips (x2) - Small plastic clips for organizing cables.
  • Part F: Cable Management Tray (x1) - Metal tray for storing cables.
  • Part G: RGB Light Bar Housing (x1) - Unit to house the RGB light bar.
  • Part H1: Bracket (x1) - Metal mounting bracket.
  • Part H2: Bracket (x2) - Metal mounting brackets.
  • Part I: Foot Caps (x2) - Protective caps for the bottom of the legs.
  • Part J1: Connector Bracket (x1) - Small metal bracket.
  • Part J2: Connector Bracket (x1) - Small metal bracket.

Installation Guide

1. Step 01: Assemble Main Frame

   Attach the two crossbars (Part B) to the top of the two desk legs (Part A) using screws labeled 'L' (likely M8x16 screws, x4) and nuts labeled 'M' (likely M8 nuts, x2). Ensure the frame is stable. Note: Screws need to be checked and tightened again after the whole desk is finished installation.

2. Step 02: Attach Support Brackets

   Attach the support brackets (Part C1 and Part C2) to the assembled frame structure using screws labeled 'L' (x4) and nuts labeled 'M' (x2). These brackets add rigidity to the frame.

3. Step 03: Attach Desktop to Frame

   Carefully place the desktop (Part D) upside down on a protected surface. Position the assembled frame onto the underside of the desktop. Secure the frame to the desktop using sixteen screws labeled 'Kx16' (likely M4x14 screws).

4. Step 04: Install Cable Management

   Attach the cable management clips (Part E) and the cable management tray (Part F) to the underside of the desktop. Use screws labeled 'N' (x4) and 'Kx6' (likely M4x14 screws) as indicated in the diagram.

5. Step 05: Attach Connector Brackets

   Attach the connector brackets (Part J1 and Part J2) to the frame structure using screws labeled 'Kx4' (likely M4x14 screws).

6. Step 06: Install Additional Brackets

   Attach the brackets (Part H1 and Part H2) to the frame. Use screws labeled 'Kx3' and 'Kx6' as shown in the diagram.

7. Step 07: Mount RGB Light Bar Housing

   Attach the RGB light bar housing (Part G) to the underside of the desktop using screws labeled 'Kx2'.

8. Step 08: Attach Foot Caps

   Place the desk upright. Attach the foot caps (Part I) to the bottom of the desk legs.

RGB LIGHT BAR INSTRUCTION

Follow these instructions to operate the integrated RGB light bar:

• Power on/off: Press button (09) until all three modes have been switched on.
• Switching mode: Press button (09).
  • Mode 1: Acoustic sensing mode (lights react to sound).
  • Mode 2: Button (10) control mode (manual selection).
• Switching color: Press button (10) to cycle through available colors in Mode 2.

Note: Button '09' is typically the power/mode button, and button '10' is the color selection button.

SERVICE & SUPPORT

If you have any questions or require support, please contact the NITHO Team:

Email: support@nitho.com

Website: www.nitho.com

NITHO GmbH

Victoriastrasse 3b

86150 Augsburg - Germany

Follow us on social media:

• Instagram: NITHOGAMES
• Facebook: NITHOGAMES