Owner Manual

STEP-1

Insert part (E) into part (F), ensuring all holes align. Connect part (E) to part (F) with screw #4, and tighten with screwdriver #13. The diagram shows part E sliding into a groove on part F, with three screws (#4) being driven through pre-drilled holes from the side of F into E, using screwdriver #13.

Document Version: 06/24

STEP-2

Insert the assembled panel (E&F) into panel (D), aligning all holes. Tighten using allen key #12. The diagram shows the EF assembly being inserted into slots on panel D, with screws being tightened from the inside of D using allen key #12.

Document Version: 07/24

STEP-3

Insert panel (B) into panel (D), aligning all holes. Tighten using allen key #12. The diagram shows panel B being attached to the opposite side of panel D from the EF assembly, using allen key #12.

Document Version: 08/24

STEP-4

Insert side panel (C) into the corresponding holes of the pre-assembled unit from step 3. Ensure all holes align and use allen key #12 to tighten. The diagram shows panel C being attached to the side of the main assembly (D, B, EF), with allen key #12 used for tightening.

Document Version: 09/24

STEP-5

Connect part (A) to the unit pre-assembled at step 4 using bolt #1 and flat washer #2. Tighten the bolt with allen key #12. The diagram shows the top panel (A) being placed onto the main body and secured from underneath with four bolts (#1) and four washers (#2), tightened with allen key #12.

Document Version: 10/24

STEP-6

Insert back panel (G) into the groove of the pre-assembled unit from step 5. Ensure all holes align and use screw #3 to attach them. Tighten screw #3 with screwdriver #13. The diagram shows back panel G sliding into grooves on the rear of the unit and being secured with ten screws (#3) using screwdriver #13.

Document Version: 11/24

STEP-7

Connect part #7 (anti-collapse bracket) to parts (C&D) using screw #8. Tighten screw with screwdriver #13. The diagram shows two brackets (#7) being attached to the rear sides of the unit (near C and D) using screws #8 and screwdriver #13.

Document Version: 12/24

STEP-8

Insert part (H) into the pre-assembled unit from step 7. Ensure all holes align and use screw #4 to attach them. Tighten screw #4 with screwdriver #13. The diagram shows part H (likely a drawer support or internal component) being attached to the inside rear of the unit, near panel G and F, using screws #4 and screwdriver #13.

Document Version: 13/24

STEP-9

Insert part #6 (likely an electrical component or light) into the pre-assembled unit from step 8. Ensure all holes align and use screw #3 to attach them. Tighten screw #3 with screwdriver #13. The diagram shows part #6 being mounted onto part H, secured with screws #3 and screwdriver #13.

Document Version: 14/24

STEP-10

Connect parts (J&K) to part (I) using screw #4 and tighten with screwdriver #13. Slide part (O) into the groove in part (J&K). Ensure they are also in the groove in part (I). This step describes the initial assembly of a drawer. The diagram shows J and K attached to the sides of I, with O sliding into grooves. Screws #4 and screwdriver #13 are used.

Document Version: 15/24

STEP-11

Connect parts (J&K) to part (N) using screw #4 and tighten with screwdriver #13. This step appears to be attaching the drawer frame (J&K) to a drawer slide component (N). The diagram shows J&K being attached to N using screws #4 and screwdriver #13.

Document Version: 16/24

STEP-12

1. Pull out the slide and attach the drawer (I) to it, ensuring the slide is in the groove of part (J/K) and reaches the drawer front (I). 2. Connect the drawer to the slide with screw #5 and tighten with screwdriver #13. The diagram shows drawer I being attached to drawer slides (part of J/K and N assembly) using screws #5 and screwdriver #13.

Document Version: 17/24

STEP-13

1. Connect parts (L&M) to part (I) using screw #4 and tighten with screwdriver #13. 2. Slide part (P) into the groove in part (L&M). Ensure they are also in the groove in part (I). This step describes assembling another drawer. The diagram shows L and M attached to the sides of I, with P sliding into grooves. Screws #4 and screwdriver #13 are used.

Document Version: 18/24

STEP-14

Connect parts (L&M) to part (N) using screw #4 and tighten with screwdriver #13. This step attaches the second drawer frame (L&M) to a drawer slide component (N). The diagram shows L&M being attached to N using screws #4 and screwdriver #13.

Document Version: 19/24

STEP-15

1. Pull out the slides and attach the drawers to them. Ensure the slides are in the groove of part (L/M) and reach the drawer front (I). 2. Connect the drawer to the slide with screw #5 and tighten with screwdriver #13. This step attaches the assembled drawers (from step 13/14) to the main unit's slides. The diagram shows multiple drawers being attached using screws #5 and screwdriver #13.

Document Version: 20/24

STEP-16

⚠️ Attention: Before the next step, adjust the feet of the locker to keep it level.

The diagram shows a warning icon and two circular insets: one showing a foot being adjusted with a cross icon (❌), and another showing a foot being rotated with a checkmark icon (✔️).

Document Version: 21/24

STEP-17

1. Install the anti-collapse device. 2. Mark the position on the wall corresponding to part (#7) on the unit (C&D). Drill and insert expandable screw (#10) by hammer. 3. Assemble part (#7) to the wall. Align the hole in part (#7) with expandable screw (#10), use screw (#9) to attach it and tighten by screwdriver (#13). The diagram shows the anti-collapse bracket (#7) being attached to the wall using expandable screw #10 and screw #9, with screwdriver #13.

Document Version: 22/24

STEP-18

1. Let the plastic belt (#11) pass through both parts (#7) and pull tightly. This step connects the wall-mounted brackets (#7) to the furniture using the plastic belt (#11). The diagram shows the belt being threaded through the brackets on the wall and the furniture, then pulled taut.

Document Version: 23/24