Owner Manual
Document Version: 01/20
Important Safety Information
NOTE: This brochure contains IMPORTANT safety info. Please read and keep for future reference.
Maintenance and Warnings
- We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
- Carefully check that you have all the parts before beginning assembly.
- Keep fittings out of children's reach and keep children well away from construction area.
- We suggest you retain these instructions for future reference.
- Keep furniture away from heat sources.
- Do not clean furniture with harsh cleaner or polishes.
- Do not use detergents, solvents, abrasives, spray packs, or leather cleaner.
- Use non-colored mild soap with warm water to clean spills (Mix 1:10 soap to water).
- Do not place furniture under direct sunlight; material will possibly fade over time.
- Do not use on-site dry cleaning machines. Children should not climb or jump on the furniture.
- Do not write on furniture that is not protected by a padded barrier.
- Not for commercial use, only for residential use.
Weight Limitation: 900 LBS [Weight Limit Symbol]
Document Version: 02/20
Parts List
Box-A
| Part A | x1 | Description: Seat cushion module. [Line drawing of a seat cushion module.] |
Box-B
| Part B | x1 | Description: Seat cushion module. [Line drawing of a seat cushion module.] |
Box-C
| Part C | x1 | Description: Right armrest module. [Line drawing of a right armrest module.] |
| Part D | x1 | Description: Left armrest module. [Line drawing of a left armrest module.] |
| Part E | x2 | Description: Headrest. [Line drawing of a headrest.] |
| Part F | x8 | Description: Furniture leg with a threaded bolt. [Line drawing of a furniture leg with a threaded bolt.] |
| Part G | x4 | Description: Metal furniture leg with a mounting plate. [Line drawing of a metal furniture leg with a mounting plate.] |
| Part H | x1 | Description: Power adapter with multiple ports and a power cord. [Line drawing of a power adapter with multiple ports and a power cord.] |
| Part I | x1 | Description: Electrical cables with connectors. [Line drawing of electrical cables with connectors.] |
Tools needed: [Estimated Time] Around 45min [Number of Persons] Two persons
Document Version: 03/20
Hardware List
| Part # | Quantity | Description |
|---|---|---|
| #1 | x8 | Ø8x100mm Bolt. [Line drawing of a long bolt.] |
| #2 | x16 | Ø6x15mm Bolt. [Line drawing of a short bolt.] |
| #3 | x8 | Ø6x30mm Bolt. [Line drawing of a medium bolt.] |
| #4 | x8 | Ø8x15mm Flat washer. [Line drawing of a flat washer.] |
| #5 | x8 | Ø8 Nut. [Line drawing of a nut.] |
Tool List
| Part # | Quantity | Description |
|---|---|---|
| #6 | x1 | M6 Allen wrench. [Line drawing of an M6 Allen wrench.] |
| #7 | x1 | M4 Allen wrench. [Line drawing of an M4 Allen wrench.] |
| #8 | x1 | Tool for tightening bolts/nuts. [Line drawing of a tool for tightening bolts/nuts.] |
Hardware Spare List
| Part # | Quantity | Description |
|---|---|---|
| #1 | x1 | Ø8x100mm Bolt. [Line drawing of a long bolt.] |
| #2 | x1 | Ø6x15mm Bolt. [Line drawing of a short bolt.] |
| #3 | x1 | Ø6x30mm Bolt. [Line drawing of a medium bolt.] |
| #4 | x1 | Ø8x15mm Flat washer. [Line drawing of a flat washer.] |
| #5 | x1 | Ø8 Nut. [Line drawing of a nut.] |
Document Version: 04/20
Assembly Instructions
Step 1
Attach part F (furniture legs) to the underside of part A (seat cushion module) using screws. [Diagram shows attaching part F to the underside of part A using screws. A close-up shows a hand [hand-turning-screw] screwing a leg into a pre-drilled hole.]
Document Version: 05/20
Step 2
Attach part A to the base frame using four #1 bolts (Ø8x100mm). [Diagram shows attaching part A to the base frame using four #1 bolts. A close-up shows a hand [hand-turning-screw] screwing a bolt into a hole, with an arrow [arrow-right] indicating rotation.]
Document Version: 06/20
Step 3
Attach part C (right armrest module) to part A. Align holes and use hardware: #1 bolt, #4 flat washer, #5 nut, and tool #8. [Diagram shows attaching part C to part A. A close-up shows the assembly of these parts with arrows indicating the order and direction of tightening.]
Document Version: 07/20
Step 4
Connect electrical cables. [Diagram shows connecting electrical cables. Arrows [arrow-right] indicate plugging one connector into another.]
Document Version: 08/20
Step 5
Attach part G (metal legs) to the side of part C. Use #2 bolts (Ø6x15mm) and tool #6 (M6 Allen wrench). [Diagram shows attaching part G to the side of part C. A close-up shows a hand using the Allen wrench to tighten bolts.]
Document Version: 09/20
Step 6
Attach part F (furniture legs) to the underside of part B (seat cushion module) using screws. [Diagram shows attaching part F to the underside of part B using screws. A close-up shows a hand [hand-turning-screw] screwing a leg into a pre-drilled hole.]
Document Version: 10/20
Step 7
Attach part B to the base frame using four #1 bolts (Ø8x100mm). [Diagram shows attaching part B to the base frame using four #1 bolts. A close-up shows a hand [hand-turning-screw] screwing a bolt into a hole, with an arrow [arrow-right] indicating rotation.]
Document Version: 11/20
Step 8
Attach part D (left armrest module) to part B. Align holes and use hardware: #1 bolt, #4 flat washer, #5 nut, and tool #8. [Diagram shows attaching part D to part B. A close-up shows the assembly of these parts with arrows indicating the order and direction of tightening.]
Document Version: 12/20
Step 9
Connect electrical cables. [Diagram shows connecting electrical cables. Arrows [arrow-right] indicate plugging one connector into another.]
Document Version: 13/20
Step 10
Attach part G (metal legs) to the side of part D. Use #2 bolts (Ø6x15mm) and tool #6 (M6 Allen wrench). [Diagram shows attaching part G to the side of part D. A close-up shows a hand using the Allen wrench to tighten bolts.]
Document Version: 14/20
Step 11
Join part A and part B together. [Diagram shows joining part A and part B together. A close-up shows a bracket mechanism that connects the two modules.]
Document Version: 15/20
Step 12
Connect electrical cables (part I) from the sofa modules (A and B) to the power adapter (part H). [Diagram shows the assembled sofa with parts A and B joined. Electrical cables are shown connecting from the sofa modules to the power adapter. Close-ups show the connectors and the power adapter ports.]
Document Version: 16/20
Step 13
Operate the headrest mechanism. [Diagram shows the assembled sofa. A close-up illustrates how to operate the headrest mechanism, with labels 'Open the headrest' and 'Close the headrest'. Text indicates 'The same operation is performed on the other side.']
Document Version: 17/20
Step 14
Attach headrests (part E) to the top of the sofa modules (A and B). Use #3 bolts (Ø6x30mm) and tool #7 (M4 Allen wrench). [Diagram shows attaching headrests (part E) to the top of the sofa modules (A and B). This uses #3 bolts and tool #7. A close-up shows a hand using the Allen wrench to tighten bolts.]
Document Version: 18/20
Step 15
Operate the reclining and power features. [Diagram shows the assembled sofa. Close-ups illustrate operating the reclining mechanism with labels 'Open back', 'Off back', 'Restoration', 'type-c', and 'USB'. Text indicates 'The same operation is performed on the other side.']
Document Version: 19/20
Warranty Information
- We strive to offer high-quality products, and we also try our best to satisfy each and every customer that orders from us with product or service as needed.
- We provide 30 days warranty starting from the time you receive the item. Each customer must provide a record of their order such as the order number, or item receipt for any items that are out of the warranty period you may also still receive.
- Replacement parts can be purchased from our company if they are available.
Document Version: 20/20
