ASSEMBLY INSTRUCTIONS
Please check all parts and accessories according to the parts list before assembling. Make sure all contents are sufficient and in good condition. If any parts are missing or defective, please contact us via the purchasing platform message immediately to get replacement parts.
Parts List
| Part ID | Description | Quantity |
|---|---|---|
| 1 | Top panel with cutout for power module | x1 |
| 2 | Side panels | x2 |
| 3 | Main top panel | x1 |
| 4 | Side panel with holes | x1 |
| 5 | Shelf panels | x2 |
| 6 | Left vertical frame | x1 |
| 7 | Right vertical frame | x1 |
| 8 | Horizontal support bars | x2 |
| 9 | Left side frame assembly | x1 |
| 10 | Right side frame assembly | x1 |
| 11 | Long horizontal bars | x4 |
| 12 | Short horizontal bars | x2 |
| 13 | Central vertical support | x1 |
| 14 | Drawer box sides | x6 |
| 15 | Drawer box front/back | x6 |
| 16 | Drawer box bottom | x6 |
| 17 | Drawer box top | x6 |
| R | Drawer rails (Right) | x12 |
| L | Drawer rails (Left) | x12 |
Hardware List
| ID | Description | Quantity |
|---|---|---|
| A | M6x50mm screw | x8 |
| B | M6x23mm screw | x24 |
| C | M6x12mm screw | x4 |
| D | M4x10mm screw | x8 |
| E | M4x8mm screw | x24 |
| F | M3.5x10mm screw | x6 |
| G | Wall anchor | x2 |
| H | M4x60mm screw | x2 |
| J | Power outlet module | x1 |
| K | LED strip | x1 |
| M | Drawer handle | x12 |
| N | Adjustable foot | x8 |
| P | Mounting bracket | x2 |
| Q | M4x10mm screw | x3 |
Exploded Drawing
A visual representation showing all parts disassembled and their relative positions before assembly. It details how the main frame, side units, shelves, and drawers fit together.
STEP 1: HOW TO INSTALL
Parts used: Part 6 (Left vertical frame) (x1), Part 7 (Right vertical frame) (x1), Part 9 (Left side frame assembly) (x1), Part 10 (Right side frame assembly) (x1), Part N (Adjustable foot) (x8).
Description: Attach 8 adjustable feet (N) to the bottom of the four main vertical frame components (6, 7, 9, and 10). These feet allow for leveling the unit.
STEP 2: HOW TO INSTALL
Parts used: Part 11 (Long horizontal bars) (x4), Part B (M6x23mm screws) (x8).
Description: Connect vertical frames 6 and 9 using two long horizontal bars (11) on each side, secured with M6x23mm screws (B). Similarly, connect frames 7 and 10. The side with 2 holes on frames 7 & 10, and 6 & 9 should face inwards (towards the center of the unit).
STEP 3: HOW TO INSTALL
Parts used: Part 12 (Short horizontal bars) (x2), Part C (M6x12mm screws) (x4).
Description: Attach two short horizontal bars (12) between the assembled frame sections (6 & 7, and 9 & 10) using M6x12mm screws (C). The square holes of part 7 & 6 should face inwards.
STEP 4: HOW TO INSTALL
Parts used: Part 13 (Central vertical support) (x1), Part B (M6x23mm screws) (x2).
Description: Insert the central vertical support (13) between the frame sections and align its square holes with the square holes of parts 6 & 7. Secure with M6x23mm screws (B).
STEP 5: HOW TO INSTALL
Parts used: Part 5 (Shelf panels) (x2), Part D (M4x10mm screws) (x4).
Description: Attach two shelf panels (5) to the upper sections of the frame using M4x10mm screws (D). These shelves are positioned on the left and right sides of the main structure.
STEP 6: HOW TO INSTALL
Parts used: Part 3 (Main top panel) (x1), Part B (M6x23mm screws) (x2).
Description: Place the main top panel (3) onto the central frame structure. Secure it from underneath using M6x23mm screws (B). The side with 3 holes of part 3 faces backwards.
STEP 7: HOW TO INSTALL
Parts used: Part A (M6x50mm screws) (x4).
Description: Attach the main top panel (3) to the vertical supports using M6x50mm screws (A). These screws go into pre-drilled holes on the sides of the main top panel and the vertical frames.
STEP 8: HOW TO INSTALL
Parts used: Part 2 (Side panels) (x2), Part B (M6x23mm screws) (x4).
Description: Attach the two side panels (2) to the top of the left and right frame assemblies using M6x23mm screws (B).
STEP 9: HOW TO INSTALL
Parts used: Part A (M6x50mm screws) (x4).
Description: Secure the side panels (2) to the main structure using M6x50mm screws (A). These screws connect the side panels to the main top panel (3).
STEP 10: HOW TO INSTALL
Parts used: Part 8 (Horizontal support bars) (x2), Part B (M6x23mm screws) (x4).
Description: Install two horizontal support bars (8) into the central section of the dresser frame using M6x23mm screws (B). The side with 2 holes of part 8 should be facing up.
STEP 11: HOW TO INSTALL
Parts used: Part 1 (Top panel with cutout) (x1), Part F (M3.5x10mm screws) (x4), Part P (Mounting bracket) (x2), Part K (LED strip) (x1).
Description: On the top panel with cutout (1), attach two mounting brackets (P) using M3.5x10mm screws (F). Then, attach the LED strip (K) to the panel, likely using its adhesive backing after removing the protective tape. The LED strip is routed through the brackets.
STEP 12: HOW TO INSTALL
Parts used: Part B (M6x23mm screws) (x4).
Description: Attach the assembled top panel (1) with the LED strip to the main dresser structure using M6x23mm screws (B). The square hole of part 1 should face backwards.
STEP 13: HOW TO INSTALL
Parts used: Part 4 (Side panel with holes) (x1), Part D (M4x10mm screws) (x4), Part Q (M4x10mm screws) (x3).
Description: Attach the side panel with holes (4) to the side of the dresser using M4x10mm screws (D) and M4x10mm screws (Q). This panel likely covers the electrical components or provides access.
STEP 14: HOW TO INSTALL
Parts used: Part R (Drawer rails - Right) (x12), Part L (Drawer rails - Left) (x12).
Description: Install the drawer rails (R and L) into the designated slots within the dresser frame. There are corresponding L and R marks on each part. The diagram shows how to insert the upper part of the rail into the square hole, then insert the rest horizontally, and finally press down to ensure proper installation.
Diagram Description: Step 1 shows inserting the upper part of the rail into the square hole. Step 2 shows inserting the rest of the rail horizontally. Step 3 shows pressing down the rail to ensure proper installation.
STEP 15: WALL MOUNTING
Parts used: Part G (Wall anchor) (x2), Part H (M4x60mm screw) (x2).
Description: This step describes how to secure the dresser to the wall for stability. Place the dresser against the wall, locate and mark two holes. Drill holes in the wall, insert wall anchors (G), and then secure the dresser using M4x60mm screws (H) through the designated points on the dresser into the wall anchors.
Diagram Description: Step 1 shows positioning the dresser and marking holes. Step 2 shows drilling holes and inserting wall anchors. Step 3 shows inserting anchors into the wall. Step 4 shows securing the dresser to the wall with screws.
STEP 16: DRAWER ASSEMBLY
Parts used: Part 15 (Drawer box front/back) (x6), Part 17 (Drawer box top) (x6), Part E (M4x8mm screws) (x12), Part M (Drawer handle) (x6).
Description: Assemble the drawer boxes. Take a drawer front/back (15) and a drawer top (17). Insert the top into the slot on the front/back. Secure the drawer box sides and bottom (not explicitly shown in this step but implied by the final drawer image) using M4x8mm screws (E). Attach drawer handles (M) to the drawer fronts.
STEP 17: DRAWER ASSEMBLY
Parts used: Part 14 (Drawer box sides) (x6), Part 16 (Drawer box bottom) (x6), Part E (M4x8mm screws) (x12), Part M (Drawer handle) (x6).
Description: Continue assembling the drawer boxes. Take drawer box sides (14) and the drawer box bottom (16). Insert the bottom into the grooves of the sides. Secure the assembly with M4x8mm screws (E). Attach drawer handles (M) to the drawer fronts (which were likely assembled in Step 16).
STEP 18: INSERT DRAWERS
Description: Insert the assembled drawers (parts 14, 15, 16, 17) into the dresser frame, aligning them with the installed drawer rails (R and L).
Diagram Description: Shows drawers being inserted into the frame. Some drawers are shown fully inserted, others partially inserted, and one is shown outside the frame.
STEP 19: INSTALL POWER MODULE & LED
Parts used: Part F (M3.5x10mm screws) (x2), Part J (Power outlet module) (x1).
Description: Install the power outlet module (J) into the cutout on the main top panel (1). Secure it using M3.5x10mm screws (F).
Note: The LED strip (K) was likely connected in Step 11 and routed through the panel.
Aftersale Service
Dear customer, Thank you so much for purchasing the product from us, we really appreciate your support. We are aimed to provide the best shopping experience to our customers. We also want to build a mutually beneficial relationship with our customers, and step further to make our brand both reliable, responsible and recommendable. We hope that our products could meet your needs and expectations, please consider us again if you need more products for your home and kitchen. The package would be out of our control during shipping, please contact us through your purchasing channel directly if there is anything wrong with the box or contents. We are always here offering you our service. We will reply your messages within 24 hours, please kindly wait for the response from our professional service team. Your comfort and contentment are of utmost importance. Best Regards, Customer Care Specialist
