JLab JBuds Band Wireless Earbuds

Initial Setup: Bluetooth Pairing

Follow these steps to pair your JLab JBuds Band with your device.

Step 1: Activate Bluetooth

Enable Bluetooth in your device's settings.

[Smartphone screen showing Bluetooth enabled in settings.]

Step 2: Enter Pairing Mode

Press and hold the button on the earbuds for 10 seconds. Release the button. The indicator light will blink red and blue, indicating pairing mode.

[Earbud diagram showing button press and red/blue blinking indicator light.]

Step 3: Connect to Device

In your device's Bluetooth settings, select "JLab JBuds Band". The indicator light will blink blue slowly once paired via Bluetooth.

[Smartphone screen showing "JLab JBuds Band" selected in Bluetooth settings.]

Regular Use

Once your JLab JBuds Band has been paired with your device for the first time, the earbuds will automatically connect to your Bluetooth device whenever it is powered on. Refer to the "Button Functions" section for more details.

Button Functions

Volume & Track Control

• Volume Up: Single click.
• Next Track: Press and hold for over 2 seconds.
• Volume Down: Single click.
• Previous Track: Press and hold for over 2 seconds.

Playback & Calls

• Play/Pause/Answer/End Call: Single click.
• Reject Incoming Call: Press and hold for 1 second.

Voice Assistant

• Activate Siri (iOS) or OK Google (Android): Double click.

Bluetooth Pairing

• Bluetooth Pairing: Follow the instructions in "Initial Setup: Bluetooth Pairing".

Equalization Modes

Quickly press both buttons to cycle through three equalization modes. The JBuds Band will cycle through three EQ settings.

• JLab Signature (One Beep): JLab C3™ signature sound with amplified vocals and bass.
• Balanced (Two Beeps): Harmonious sound without extra amplification.
• Bass Boosted (Three Beeps): Amplified bass and sub-bass frequencies.

Voice Prompts

• Power On: Audible tone.
• Bluetooth Connected: Two beeps.
• Low Battery: "Low battery" voice prompt (less than 20%).
• Power Off: Audible tone.

Charging

Step 1: Connect Charger

Open the USB port cover and connect the cable to a computer or USB power source.

[Earbud diagram showing USB port cover opening and cable connection.]

Step 2: Charging Indicator

The indicator light will turn solid red, without blinking, to show charging is in progress. It will turn blue when fully charged.

[Earbud diagram showing charging indicator lights: solid red for charging, solid blue for fully charged.]

Wearing

Step 1: Choose Ear Tip Size

Select the size of your ear tips for a comfortable fit.

[Diagram showing different sizes of ear tips.]

Step 2: Position Earbuds

Position the earbud for a secure fit using the adjustable ear tip placement.

[Diagram illustrating adjustable ear tip placement for optimal fit.]

Step 3: Wear Neckband

Place the neckband around your neck with the controls located on the right side.

[Diagram showing the neckband being worn around the neck with controls on the right.]

Troubleshooting Connection Issues

JLab JBuds Band Not Appearing on My Device

1. Access your device's settings and disable Bluetooth, then re-enable it.

[Smartphone screen showing Bluetooth being toggled off and on.]

2. If JLab JBuds Band still does not appear on your device, repeat the "Initial Setup: Bluetooth Pairing" instructions.

[Smartphone screen showing Bluetooth settings.]

JLab JBuds Band Not Connecting to My Device After Powering On

1. In your device's settings, "forget" the JLab JBuds Band.

[Smartphone screen showing "JLab JBuds Band" in the device list.]

2. Access your device's settings, disable Bluetooth, then re-enable it.

[Smartphone screen showing Bluetooth being toggled off and on.]

3. Repeat the "Initial Setup: Bluetooth Pairing" instructions.

[Smartphone screen showing Bluetooth settings.]

Bluetooth Connected to an Unwanted Device

Note: The JLab JBuds Band can remember up to 8 devices. It will attempt to connect automatically to the last device used.

1. If multiple devices were previously connected to the JLab JBuds Band, disable Bluetooth on the unwanted devices, then enable Bluetooth on the desired device.

[Smartphone screens showing multiple Bluetooth devices.]

2. Press and hold the button for 10 seconds. Release the button. The indicator light blinks red and blue to indicate pairing mode. To pair, select "JLab JBuds Band" in your device's settings. The indicator light blinks blue slowly once paired via Bluetooth.

[Earbud diagram showing button press and red/blue blinking indicator light, followed by smartphone screen showing connection.]

Warning

Ensure the USB port cover is closed and attached. This ensures protection against moisture and water damage.

[Earbuds diagram showing USB port cover closed for protection.]

Before charging, the JLab JBuds Band must be completely dry. Exposure to moisture can damage internal components. It is recommended to let it air dry before charging.

[Earbuds diagram showing them air drying.]

Cautions

• Avoid any moisture or liquid inside the ear tips or charging port.
• Avoid exposing the product to extreme heat, cold, or humidity.
• Do not drop the earbuds or step on them. Avoid damaging the cable by pulling it quickly, exerting excessive force, or bending it at a sharp angle.
• Earwax may accumulate in the ear tips, which can degrade audio quality. Carefully remove earwax using a cotton swab or other small object to improve audio quality.
• If you experience discomfort or pain, try lowering the volume or stop using the device temporarily.
• If you experience recurring discomfort while using this product, stop using it and consult a doctor.
• We recommend caring for your earbuds as you would a pair of sunglasses, and storing them in a secure place when not in use.