JLab JBuds Band Wireless Headphones

Warranty Information

YOUR WARRANTY

All warranty claims are subject to JLab Audio authorization and our sole discretion. Keep your proof of purchase to ensure warranty coverage.

Contact Us

You can contact us via email at support@jlabaudio.com or visit us at intl.jlabaudio.com/contact.

Register Today

Visit intl.jlabaudio.com/register for product updates, usage tips, and FAQs.

First Time Setup: Bluetooth Pairing

1. Step 1: Enable Bluetooth

   Turn on Bluetooth in your device's settings.

   [Visual: Smartphone screen showing Bluetooth enabled]

2. Step 2: Enter Pairing Mode

   Press and hold the button for 10 seconds. Release. A light will flash red and blue to indicate pairing mode.

   [Visual: Earbuds with button being pressed, showing red/blue flashing light]

3. Step 3: Connect to Device

   Select "JLab JBuds Band" in your Bluetooth device settings to connect. A blue light will flash slower when Bluetooth is paired.

   [Visual: Smartphone screen showing "JLab JBuds Band" selected in Bluetooth settings]

Recurring Use

Once the JLab JBuds Band has initially paired with your device, the earbuds will automatically connect to the Bluetooth device when you turn them ON again. (Follow the instructions for BUTTON FUNCTIONS.)

Button Functions

• Volume Up: Click once.
• Next Track: Press and hold for over 2 seconds.
• Power On/Off: Press and hold for 2 seconds.
• Play/Pause/Answer Call: Click once.
• End Call: Click once.
• Reject Incoming Call: Press and hold for 1 second.
• Activate Siri (iOS) or "OK Google" (Android): Double-click.
• Bluetooth Pairing: Refer to the first-time setup: Bluetooth pairing instructions.
• Volume Down: Click once.
• Previous Track: Press and hold for over 2 seconds.

Equalizer (EQ) Mode

Press the button 3 times for different EQ settings (the JBuds Band will cycle through 3 EQ settings).

• JLab Signature Mode (One Beep): JLab C3™ signature sound with boosted voice and bass.
• Balanced Mode (Two Beeps): Balanced sound without additional adjustments.
• Bass Boost Mode (Three Beeps): Amplified bass and sub-bass.

Audio Cues

• Power On: Beep.
• Connected to Bluetooth: Two Beeps.
• Low Battery: "Low battery" voice prompt (below 20%).
• Power Off: Beep.

Charging

1. Step 1: Connect Charger

   Open the USB port cover and connect the cable to a computer or USB power source for charging.

   [Visual: Earbuds with USB port cover open, connected to a cable]

2. Step 2: Charging Status

   A red light will stay on while charging and turn blue when fully charged.

   [Visual: Charging indicator light on earbuds]

Fit Adjustment

1. Step 1: Choose Ear Tip Size

   Select the appropriate ear tip size for a comfortable fit.

   [Visual: Different sizes of ear tips]

2. Step 2: Adjust Earbud Position

   Move the earbud to the desired position using the adjustable earbud placement.

   [Visual: Earbud being adjusted within the ear]

3. Step 3: Wear Neckband

   Place the neckband around your neck with the controls on the right side.

   [Visual: Person wearing the neckband headphones]

ATP (Adjustable Earbud Placement)

• Position 1: Comfortable, deeper fit.
• Position 2: Relaxed, shallower fit.

Connection Troubleshooting

Can't See JLab JBuds Band on My Device

1. Turn off Bluetooth and then go to your device's settings.

   [Visual: Smartphone screen showing Bluetooth turned off]

2. If you still don't see JLab JBuds Band, repeat the FIRST TIME SETUP: BLUETOOTH PAIRING instructions.

   [Visual: Smartphone screen searching for Bluetooth devices]

JLab JBuds Band Won't Reconnect to My Device After Turning On

1. In your device's settings, select "Forget JLab JBuds Band".

   [Visual: Smartphone Bluetooth settings showing "JLab JBuds Band" with a "forget" option]

2. Turn off Bluetooth and then go to your device's settings.

   [Visual: Smartphone screen showing Bluetooth turned off]

3. Repeat the FIRST TIME SETUP: BLUETOOTH PAIRING instructions.

   [Visual: Smartphone screen connecting to "JLab JBuds Band"]

Bluetooth is Connecting to an Unwanted Device

Note: JLab JBuds Band can remember up to 8 devices. It will try to automatically connect to the last used device.

1. If more than one device was previously connected to JLab JBuds Band, turn OFF Bluetooth on the unwanted devices and turn ON Bluetooth on the selected device.

   [Visual: Smartphone screen showing multiple connected Bluetooth devices, one deselected]

2. Press and hold the button for 10 seconds. Release. A light will flash red and blue to indicate pairing mode. Select "JLab JBuds Band" in your device settings to connect. A blue light will flash slower when Bluetooth is paired.

   [Visual: Earbuds in pairing mode and smartphone screen connecting]

Caution

• Ensure the USB port cover is closed and secure. This protects it from sweat and water damage. [Visual: USB port cover closed]
• Before charging, the JLab JBuds Band headphones must be completely dry. Exposure to moisture can damage internal components. Before charging, it is best to let them air dry. [Visual: Earbuds air drying]

Warning

• Avoid moisture or liquid entering the earbud tip or charging port.
• Avoid extreme heat, cold, and humidity.
• Avoid dropping or crushing the earbuds, yanking the cable quickly or with excessive force, or bending the cable at sharp angles.
• Earwax may build up on the ear tips, reducing sound quality. Carefully remove earwax with a cotton swab or small tool to improve sound quality.
• If you experience discomfort or pain, try lowering the volume or stop using them temporarily.
• If you regularly experience discomfort while using this product, discontinue use and consult your doctor.
• We recommend treating the earbuds like sunglasses, keeping them in a safe place when not in use.