Tribesigns Bookcases Assembly Instructions
Model No. HOGA-XK00302, HOGA-XK00408, HOGA-XK00544
Contact Information
Customer Support:
Phone: 1-424-206-5666
Email: support@yuzhouint.com
Support Hours:
Monday to Friday: 1:00 PM to 1:00 AM GMT
Customer Satisfaction:
Tribesigns prioritizes customer satisfaction. If you encounter any issues with your product, such as missing or damaged parts, please retain the original packaging, take photos of the packaging and the product, and contact customer support promptly.
Warm Tips for Assembly
- Carefully read and keep these instructions for future reference.
- Before assembling, ensure all parts and accessories are present.
- Assemble on a soft, smooth surface, such as a carpet, to avoid scratches.
- Do not fully tighten screws until all parts are correctly in place.
- We recommend using hand tools for assembly. If an electric screwdriver is used, reduce its power to protect the product.
Anti-Tip Straps Installation
Using the anti-tip straps can reduce the risk of tipping over, but cannot eliminate it entirely. Please follow the provided instructions for secure installation.
Parts Identification
Parts List:
The following parts are included in the package. Please check all parts. Most board parts are labeled on the edge. Contact customer support for a free replacement if any parts are damaged or missing.
- Part 1: 1 pc
- Part 2: 1 pc
- Part 3: 2 pcs
- Part 4: 1 pc
- Part 5: 1 pc
- Part 6: 1 pc
- Part 7: 1 pc
- Part 8: 1 pc
- Part 9: 1 pc
- Part 10: 1 pc
- Part 11: 1 pc
- Part 12: 1 pc
- Part 13: 4 pcs
- Part 14: 1 pc
- Part 15: 1 pc
- Part 16: 1 pc
- Part 17: 1 pc
- Part 18: 2 pcs
- Part 19: 2 pcs
- Part 20: 4 pcs
Hardware List:
- F (M6x30MM): 28 pcs
- H (M6x40MM): 26 pcs
- I (M6x50MM): 2 pcs
- N (M6x10MM): 16 pcs
- M (M6 Washer): 8 pcs
- X (Bracket 20x20MM): 4 pcs
- Y (Foot Pad): 4 pcs
- Z (Anti-tip strap kit): 2 pcs
Assembly Steps
- Step 1: Attach foot pads (Y) to the bottom of side frames (8 and 9).
- Step 2: Attach base panel (2) to side frames (8 and 9) using screws (N) x4.
- Step 3: Attach the lower shelf (3) to the side frames using screws (N) x2.
- Step 4: Attach the curved decorative pieces (13) to the side frames using screws (H) x2.
- Step 5: Attach brackets (X) to the top of the side frames using screws (F+M) and (N+M).
- Step 6: Attach support pieces (20) to the side frames using screws (H) x4.
- Step 7: Attach the middle shelf (12) to the side frames using screws (H) x2.
- Step 8: Attach the next shelf (3) using screws (F) x4.
- Step 9: Attach the top panel (1) to the side frames using screws (F) x4.
- Step 10: Attach the decorative pieces (13) to the side frames using screws (F+M) x2.
- Step 11: Attach the top shelf (5) using screws (N) x2.
- Step 12: Attach the remaining shelves (6, 7) using screws (F) x4.
- Step 13: Attach the side panel (11) to the assembled structure using screws (N+M) x2.
- Step 14: Attach the remaining shelves (16, 17) using screws (I) x2 and (H) x2.
- Step 15: Secure the top of the bookcase with screws (H) x4.
- Step 16: Attach the decorative elements (18) to the top panel (1) using screws (F) x4.
- Step 17: Install the anti-tip straps (Z) to the back of the bookcase and the wall according to the provided diagram.
Important Safety Information
Caution: Do not press hard on the table edge.
