Tribesigns

Contact Us

We're here to help you.

Email: support@tribesigns.com

Phone: 1-424-220-6888 (Contact us anytime except 12:00 AM to 8:00 AM EST)

Your satisfaction is our top priority. If you encounter any issues, such as missing or damaged parts, please retain the original packaging, take photos of the packaging and product, and contact us as soon as possible.

Warm Tips

• Carefully read these instructions and keep them for future reference.
• Check the parts list and confirm everything is present before starting assembly.
• When assembling, place all parts on a soft, smooth surface like a carpet to avoid scratches.
• Do not fully tighten screws until all parts are confirmed in place to avoid misalignment.

How to Get the Assembly Video

Step 1: Scan the QR code for the installation video.

Step 2: Alternatively, search for the Model No. (found on the bottom left corner of the title page) on the Tribesigns website or YouTube.

Note: If you cannot find the assembly video, please contact customer service.

General Assembly Advice

We recommend using hand tools for assembly. If an electric screwdriver is used, reduce power and torque to avoid damage to the product. ⚙️

Important Safety Note: Install the tip-over restraint provided. Use of tip-over restraints may only reduce but not eliminate, the risk of tip-over. ⚠️

Make sure all parts are included. Most board parts are labeled or stamped on the raw edge. Contact Tribesigns for a free replacement if you encounter any damaged or missing parts. ✔️

Parts List

Hardware List

Assembly Steps

Step 1: Cam and Pin Installation & Initial Frame Assembly

Cam and Pin Installation: Screw the pin into the hole. To set the cams correctly, ensure that the arrow on the cam is opening to the hole of the pin it is locking. Lock the cam by turning the cam head with a screwdriver until it is tightened. Please do not use an electric screwdriver to assemble the unit. ✔️

Diagram shows a pin being screwed into a panel. A cam is then placed over the pin, with its arrow pointing towards the pin. The cam is turned with a screwdriver to lock it. A close-up shows a pin and cam with a "No gap" indicator and a checkmark for correct installation, and a cross for incorrect installation.

Assembly: Attach part 1 (Left Side Panel) to part 3 (Bottom Panel) using 9 pieces of hardware A (M6x40MM screws). Attach part 2 (Right Side Panel) to part 3 (Bottom Panel) using 9 pieces of hardware A. Ensure correct alignment and no gaps.

Diagram shows panel 3 as the base, with panels 1 and 2 being attached vertically to its sides using screws labeled 'A'.

Step 2: Attaching Back Support Panel

Attach part 4 (Back Support Panel) to the assembly from Step 1 using hardware A.

Diagram shows panel 4 being attached to the rear of the structure formed in Step 1, using screws.

Step 3: Attaching Middle Divider and Top Panel

Attach part 5 (Middle Divider Panel) to the assembly using hardware A. Attach part 8 (Top Panel) to the assembly using hardware A. Ensure correct alignment and no gaps.

Diagram shows panel 5 being inserted horizontally into the frame and secured, and panel 8 being placed on top of the frame and secured. Screws (hardware A) are used. A close-up shows the cam lock mechanism.

Step 4: Completing the Main Frame

Complete the main frame by attaching panels 1, 2, 3, 4, and 5 using hardware A.

Diagram shows the partially assembled unit from previous steps, with additional panels being added to form a more complete box structure. Hardware A is used.

Step 5: Attaching Upper Side Panels

Attach panels 6 (Upper Left Side Panel) and 7 (Upper Right Side Panel) to the frame using hardware A.

Diagram shows panels 6 and 7 being attached to the sides of the structure, likely forming the upper section, using screws (hardware A).

Step 6: Attaching Top Panel and Upper Side Panel

Attach panel 8 (Top Panel) and panel 6 to the structure using hardware A.

Diagram shows panel 8 being placed on top and secured, and panel 6 being attached to the side. Screws (hardware A) are used.

Step 7: Securing Panels with Hardware B

Secure the structure by attaching panels 9, 8, 6, 5, 1, 2, 3, 4 using hardware B (M4.2x20MM screws).

Diagram shows the main structure with additional panels being attached to the back and sides using screws (hardware B).

Step 8: Inserting and Securing Shelves

Insert shelves (part 10) into the assembled unit and secure them using hardware B.

Diagram shows multiple shelf panels (part 10) being placed into the unit and secured with screws (hardware B).

Step 9: Attaching Lower Back Panel and Side Panels

Attach panel 11 (Back Support Panel, Lower) to the lower back section using hardware B. Attach panel 2 to the side using hardware B. Attach panel 4 to the side using hardware B. Use round caps (C) for some connections.

Diagram shows the lower back panel (11) being attached, and side panels (2, 4) being secured. Round caps (C) are shown being used.

Step 10: Inserting and Securing Upper Shelves

Insert the upper shelves (part 12) into the upper section of the unit. Secure the shelves using hardware D (M5x15MM screws), cam locks (E), and rings (F). Use hardware G for additional securing.

Diagram shows the upper shelves (part 12) being inserted. Close-ups show the cam lock (E) and ring (F) mechanism being used with screws (D) to secure the shelves. Hardware G is also shown.