LNC A04976W1 Wall Sconce Installation Guide

WARNING

(To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

Finished Product Appearance

A wall-mounted light fixture with a single conical glass shade hanging from an arm attached to a backplate.

Tools Required (Not Included)

Before starting assembly and installation, please prepare the needed tools:

• [ladder] Ladder
• [screwdriver] Philips Head or Flat Blade Screwdriver
• [tape] Electrical Tape
• [pliers] Pliers
• [wire cutters] Wire Cutter/Stripper

Parts Including

• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Hex nut (1)
• (F) Washer (1)
• (G) Iron sheet (1)
• (H) Back plate (1)
• (I) Arm (1)
• (J) Knob nut (2)
• (K) Socket (1)
• (L) Glass shade (1)
• (M) Socket ring (1)

Accessories Enclosed

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)
• (N) Wrench (1)

Assembly & Installation Instructions

Step 1: Initial Preparation

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the illustration.

Step 2: Turn Off Power

Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

• Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
• Place the wall switch in the “OFF” position.

Step 3: Make Assembly

Step A1: Prepare Arm and Back Plate

Illustration shows connecting the arm (I) through the back plate (H) and securing it with hex nut (E), washer (F), and iron sheet (G).

1. Unscrew knob nuts (J) from mounting plate (D), then set them aside for later installation.
2. Pass arm (I) through the hole in back plate (H).
3. Screw hex nut (E) through washer (F) and iron sheet (G) to arm (I) as shown in the illustration.

Step A2: Mount the Plate

Illustration shows passing supply wires from an outlet box through the mounting plate (D) and securing the mounting plate (D) to the outlet box with mounting screws (A).

Carefully pass the supply wires from the outlet box through mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).

Step A3: Make Wire Connections

Illustration shows the process of connecting electrical wires, including ground wires and supply wires, using wire connectors.

Connect wires as shown in the connection diagrams. PLEASE NOTE THAT THE GROUND WIRE IS BARE COPPER WIRE; NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connecting Ground Wires

Connect ground wires according to the chart:

• Diagram A: Outlet Box Ground connected to Fixture Ground using Green Ground Screw.
• Diagram B: Outlet Box Ground connected to Fixture Ground, with a Cupped Washer and Dimples.

Connecting Supply Wires

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

Step A4: Attach Back Plate

Illustration shows aligning the back plate (H) with mounting screws and securing it to the mounting plate (D) with knob nuts (J).

Align the holes in back plate (H) with the pre-assembled mounting screws, then attach back plate (H) to mounting plate (D) with the previously removed knob nuts (J). Hand tighten until snug.

NOTE: Back plate (H) should be snug against the wall with knob nuts (J). If not, remove back plate (H), adjust the threaded length of pre-assembled mounting screws on mounting plate (D):

• Unscrew the pre-assembled hex nuts.
• Screw the pre-assembled mounting screws in or out of mounting plate (D).
• When the secure length is achieved, tighten the pre-assembled hex nuts and return to Step A4.

Step A5: Install Glass Shade and Bulb

Illustration shows attaching the glass shade (L) to the socket (K) using the socket ring (M).

1. Remove socket ring (M) from socket (K).
2. Fix glass shade (L) to socket (K) with socket ring (M).
3. Install the bulb (Not included). Please do not exceed the maximum wattage recommended on the socket.

Step 4: Final Check

Check everything is installed properly, then you could turn on the light. Enjoy!

Ordering Parts

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use the exact wording from the illustration when ordering parts.

Cleaning

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.