TP-Link Omada Gigabit Outdoor PoE+ Extender

Package Contents

The package includes:

• 1 x Omada PoE+ Extender
• Mounting Brackets (2x)
• Wall Anchors (2x)
• Screws (2x)
• Straps (3x)
• Cable Glands (2x)

Installation

The extender can be mounted in two ways: Wall Mounting or Pole Mounting.

Waterproofing

To maintain proper waterproofing, select the correct seal based on the actual cable type and outer diameter.

LED Explanation

Connections

Connect the grounding terminal to grounding facilities using the provided proper grounding wire.

Connection Diagram:

[Diagram: Power Sourcing Equipment (PSE) like a PoE Switch or Injector connects to the "PoE In" port of the Omada PoE+ Extender. The "PoE Out" port of the extender connects to a Powered Device (PD). The distance can be up to 100/250m depending on the cable type.]

Note:

1. Ensure the PSE and PD devices are connected to the corresponding ports properly.
2. For long-distance connections (over 100 meters), especially to IP cameras or similar devices, it is recommended to set the port speed of both the PSE and PD to 10 Mbps full-duplex or enable Extend Mode on the PSE.

Specifications

• Standards: IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at
• LEDs: 2 x Link/Act
• Cable Type:
  • 10BASE-T: 2-pair UTP/STP (≤250m) of Cat. 3 or above
  • 100BASE-TX: 2-pair UTP/STP (≤100m) of Cat. 5 or above
  • 1000BASE-T: 4-pair UTP/STP (≤100m) of Cat. 5e or above
• Ports: 1 x 10/100/1000 Mbps Auto-Negotiation RJ45, 1 x 10/100/1000 Mbps Auto-Negotiation RJ45
• PoE Input: Compliance with 802.3af/at devices
• Maximum PoE Output: 30W

Environmental and Physical Specifications

• Operating Temperature: -40°C to 65°C (-40°F to 149°F)
• Storage Temperature: -40°C to 70°C (-40°F to 158°F)
• Operating Humidity: 15% to 90% RH non-condensing
• Storage Humidity: 15% to 90% RH non-condensing

FAQ

Q1. Which devices can work normally with the extender?

A: Only PSE and PD devices compliant with IEEE 802.3af/at can function well with the extender. Do not use the extender with other devices to extend the data transmission distance only.

Q2. Why is the Link/Act LED not lit?

A1: Ensure your network cable is in good condition and that both the PSE (Power Sourcing Equipment) and PD (Powered Device) are properly connected to the correct ports.

A2: POE20E-Outdoor features an adaptive data rate design. Link stability may be affected by cable length, cable quality, and the characteristics of the connected devices. Under certain conditions-such as using 160-170m Cat5e cables (tested in lab environments)-intermittent connectivity may occur.

To resolve this issue:

1. Manually configure the connected device to operate at 10 Mbps full-duplex or enable Extend Mode on the PSE.
2. Adjust the cable length to avoid the affected range.

Safety Information

• Do not attempt to disassemble, repair, or modify the device. Contact TP-Link for service.
• Keep the device away from water, fire, humidity, or hot environments.
• This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1.
• Please read and follow the safety information when operating the device. TP-Link is not liable for accidents or damage due to improper use. Use this product with care and at your own risk.

FCC Compliance Information

Product Name: Gigabit Outdoor PoE+ Extender

Model Number: POE20E-Outdoor

Responsible party: TP-Link Systems Inc.

Address: 10 Mauchly, Irvine, CA 92618

Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Industry Canada Statement

CAN ICES-003(A)/NMB-003(A)

CE Declaration of Conformity

TP-Link declares that the PoE+ extender complies with essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU) 2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.

UK Declaration of Conformity

TP-Link declares that the PoE+ extender complies with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca.

Explanation of Symbols

[Symbol: Class II equipment]

[Symbol: Class II equipment with functional earthing]

[Symbol: Alternating current]

[Symbol: Direct current]

[Symbol: Polarity of d.c. power connector]

[Symbol: For indoor use only]

[Symbol: Dangerous voltage]

[Symbol: Caution, risk of electric shock]

[Symbol: Energy efficiency Marking VI]

[Symbol: Protective earth]

[Symbol: Earth]

[Symbol: Frame or chassis]

[Symbol: Functional earthing]

[Symbol: Caution, hot surface]

[Symbol: Caution]

[Symbol: Operator's manual]

[Symbol: Stand-by]

[Symbol: "ON"/"OFF" (push-push)]

[Symbol: Fuse]

[Symbol: Fuse is used in neutral N]

[Symbol: Recycling]

[Symbol: Caution, avoid listening at high volume levels for long periods]

[Symbol: Disconnection, all power plugs]

[Symbol: Switch of mini-gap construction]

[Symbol: Switch of micro-gap construction (for US version)]

[Symbol: Switch of micro-gap / micro-disconnection construction (for other versions except US)]

[Symbol: Switch without contact gap (Semiconductor switching device)]

[Diagram: Product label can be found at the bottom of the product. Symbols may vary from products.]

WEEE Directive

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. The user can choose to give their product to a competent recycling organization or to the retailer when buying new electrical or electronic equipment.

BSMI Notice

Safety Consultation and Precautions:

• Use the original power adapter or only use the power type indicated on this product.
• Unplug the power cord before cleaning. Do not use liquid, spray cleaners, or a damp cloth for cleaning.
• Beware of moisture; do not spill water or other liquids on this product.
• Slots and openings are for ventilation to ensure reliable operation and prevent overheating; do not block or cover the openings.
• Do not place this product near heat sources. Do not place in an enclosed space without normal ventilation.
• Do not open the casing or repair the product yourself. Contact the manufacturer or agent if the product malfunctions.
• Warning: To avoid electromagnetic interference, this product should not be installed or used in a residential environment.

Restricted Substances Statement:

[Table: Restricted Substances and their Chemical Symbols]

[Table: Product Component Names and Restricted Substances (Pb, Cd, Hg, Cr6, PBB, PBDE)]

[Note 1: "○" indicates that the percentage content of the restricted substance does not exceed the percentage content threshold.]

[Note 2: "-" indicates that the restricted substance is an exclusion item.]

VCCI-A

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.