TP-Link Omada Gigabit Outdoor PoE+ Extender

Package Contents

The package includes the following items:

• PoE+ Extender
• Mounting Bracket (2x)
• Plastic Wall Anchors (2x)
• Screws (2x)
• Cable Glands (3x)
• Straps (2x)

[Visual representation of package contents]

Installation

Option 1: Wall Mounting

1. Drill two holes on the wall and insert the plastic wall anchors. Secure the mounting bracket to the wall, ensuring the UP mark is on the outside and pointing upward.
2. Attach the PoE+ extender to the mounting bracket by sliding it in the indicated direction until it locks into place.

[Diagram showing wall mounting steps: drilling, anchor insertion, bracket attachment, extender installation.]

Option 2: Pole Mounting

1. Secure the mounting bracket to the pole using the provided straps. Ensure the UP mark is on the outside and pointing upward.
2. Attach the PoE+ extender to the mounting bracket by sliding it in the direction of the arrows until it locks into place.

[Diagram showing pole mounting steps: bracket attachment with straps, extender installation. A note indicates the mounting bracket can be set horizontally.]

Waterproof

To maintain proper waterproofing, select the correct seal based on the actual cable type and outer diameter.

[Diagram illustrating waterproof seal selection based on cable diameter.]

LED Explanation

The Link/Act LED indicates the status of the RJ45 port:

Connection

[Diagram description: Illustrates the connection between a Power Sourcing Equipment (PSE), such as a PoE Switch or PoE Injector, and the PoE+ Extender, and then to a Powered Device (PD). It shows RJ45 ports for connection and mentions grounding terminals. It also notes that for long-distance connections (over 100 meters), it's recommended to set the port speed to 10 Mbps full-duplex or enable Extend Mode on the PSE.]

Specifications

Standards

• IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at

LED

• 2*Link/Act

Cable Type

• 10BASE-T: 2-pair UTP/STP (250m) of Cat. 3 or above
• 100BASE-TX: 2-pair UTP/STP (100m) of Cat. 5 or above
• 1000BASE-T: 4-pair UTP/STP (100m) of Cat. 5e or above

Ports

• 1*10/100/1000 Mbps Auto-Negotiation RJ45
• 1*10/100/1000 Mbps Auto-Negotiation RJ45

PoE Input

• Compliance with 802.3af/at devices

Maximum PoE Output

• 30W

Environmental and Physical Specifications

[Note: Chinese characters in the original document specified the same values.]

Safety Information

Do not attempt to disassemble, repair, or modify the device. For service, please contact TP-Link. Keep the device away from water, fire, humidity, or hot environments.

This equipment must be powered by devices compliant with Power Source Class 2 (PS2) or Limited Power Source (LPS) as defined in IEC 62368-1.

Please read and follow the safety information. TP-Link cannot guarantee against accidents or damage due to improper use. Operate the product with care at your own risk.

Declarations of Conformity

EU Declaration of Conformity

TP-Link declares that this PoE+ extender complies with essential requirements and other provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and (EU)2015/863. The original EU declaration can be found at https://www.tp-link.com/en/ce.

UK Declaration of Conformity

TP-Link declares that this PoE+ extender complies with essential requirements and other provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK declaration can be found at https://www.tp-link.com/support/ukca.

FCC Compliance Information Statement

Product Name: Gigabit Outdoor PoE+ Extender

Model Number: POE20E-Outdoor

Responsible Party: TP-Link Systems Inc.

Address: 10 Mauchly, Irvine, CA 92618

Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Industry Canada Statement

CAN ICES-003(A)/NMB-003(A)

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

BSMI Notice

[Diagram description: A table indicating the presence of hazardous substances in the product. It lists substances like Pb, Cd, Hg, Cr+6, PBB, PBDE and shows their presence in PCB components.]

(Note: The original document contained Chinese text and symbols related to hazardous substance compliance.)

Explanation of the Symbols on the Product Label

The product label, typically found at the bottom of the device, may feature the following symbols:

FAQ

Q1. Which devices can work normally with the extender?

Only PSE and PD devices compliant with IEEE 802.3af/at can function well with the extender. Do not use the extender with other devices solely to extend data transmission distance.

Q2. Why is the Link/Act LED not lit?

A1: Ensure your network cable is in good condition and that both the PSE (Power Sourcing Equipment) and PD (Powered Device) are properly connected to the correct ports.

A2: The POE20E-Outdoor features an adaptive data rate design. Link stability may be affected by cable length, cable quality, and connected device characteristics. Under certain conditions (e.g., using 160-170m Cat5e cables), intermittent connectivity may occur. To resolve this:

• Manually configure the connected device to operate at 10 Mbps full-duplex or enable Extend Mode on the PSE.
• Adjust the cable length to avoid the affected range.