TP-Link Omada Gigabit Outdoor PoE+ Extender

Package Contents

The package includes:

• 1x Omada PoE+ Extender
• 2x Mounting Brackets
• 2x PoE In Connectors
• 2x PoE Out Connectors
• 2x Waterproof Connectors
• 2x Pole Straps
• 2x Wall Mount Screws
• 2x Wall Anchors
• 3x Cable Glands
• 2x Cable Gland Nuts

Installation

Option 1: Wall Mounting

1. Drill two holes on the wall and insert the plastic wall anchors. Secure the mounting bracket to the wall, ensuring the "UP" mark is on the outside and pointing upward.
2. Attach the PoE+ extender to the mounting bracket by sliding it in the indicated direction until it locks into place.

Option 2: Pole Mounting

1. Secure the mounting bracket to the pole using the provided straps, ensuring the "UP" mark is on the outside and pointing upward.
2. Attach the PoE+ extender to the mounting bracket by sliding it in the indicated direction until it locks into place.

Waterproofing

To maintain proper waterproofing, select the correct seal based on the actual cable type and outer diameter.

Grounding

Connect the grounding terminal to grounding facilities using the provided proper grounding wire.

LED Explanation

• Link/Act Solid Green: RJ45 port linked at 1 Gbps.
• Link/Act Solid Yellow: RJ45 port linked at 10/100 Mbps.
• Link/Act Flashing: RJ45 port transmitting or receiving data.
• Link/Act Off: RJ45 port not linked.

Connection Diagram

Connect the Power Sourcing Equipment (PSE) (e.g., PoE Switch, PoE Injector) to the "PoE In" port of the extender. Connect the Powered Device (PD) to the "PoE Out" port of the extender. The extender supports distances of 100/250m.

Note:

• Ensure PSE and PD devices are connected to the corresponding ports properly.
• The extender supports automatic speed downshift. When the distance exceeds 100 meters, the connection speed may downshift to 100 Mbps or 10 Mbps. This depends on cable quality and length and may take up to 20 seconds.
• For long-distance connections to IP cameras, it is recommended to enable "Extend" mode on the PSE or manually set the port speed of both PSE and PD to 10 Mbps.

Specifications

• Standards: IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at
• LEDs: 2x Link/Act
• Cable Type:
  • 10BASE-T: 2-pair UTP/STP (≤250m) of Cat. 3 or above
  • 100BASE-TX: 2-pair UTP/STP (≤100m) of Cat. 5 or above
  • 1000BASE-T: 4-pair UTP/STP (≤100m) of Cat. 5e or above
• Ports: 1x 10/100/1000 Mbps Auto-Negotiation RJ45 (Input), 1x 10/100/1000 Mbps Auto-Negotiation RJ45 (Output)
• PoE Input Compliance: 802.3af/at devices
• Maximum PoE Output: 30W

FAQ

• Q1: Which devices can work normally with the extender?
  A: Only PSE and PD devices compliant with IEEE 802.3af/at can function well with the extender. Do not use the extender with other devices to extend data transmission distance only.
• Q2: Why is the Link/Act LED not lit?
  A1: Ensure your network cable is in good condition.
  A2: Ensure both PSE and PD devices are connected to the correct ports.

Environmental and Physical Specifications

• Operating Temperature: -40°C to 65°C (-40°F to 149°F)
• Storage Temperature: -40°C to 70°C (-40°F to 158°F)
• Operating Humidity: 15% to 90% RH non-condensing
• Storage Humidity: 15% to 90% RH non-condensing

Safety Information

• Do not attempt to disassemble, repair, or modify the device. Contact TP-Link for service.
• Keep the device away from water, fire, humidity, or hot environments.
• This equipment can be powered only by Power Source Class 2 (PS2) or Limited Power Source (LPS) compliant equipment as defined in IEC 62368-1.
• Read and follow safety information. TP-Link is not liable for accidents or damage due to improper use. Use with care and at your own risk.

Regulatory Information

FCC Compliance: This equipment complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Industry Canada Statement: CAN ICES-003(A)/NMB-003(A)

CE Mark: TP-Link declares that the PoE+ extender complies with essential requirements and other provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU) 2015/863. The original EU declaration of conformity can be found at https://www.tp-link.com/en/ce.

UK Declaration of Conformity: TP-Link declares that the PoE+ extender complies with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK Declaration of Conformity can be found at https://www.tp-link.com/support/ukca.

Explanation of Symbols: Symbols on the product label may vary. Refer to the product label at the bottom of the product for specific symbols and their meanings, which may include Class II equipment, functional earthing, AC/DC voltage, polarity, indoor use only, dangerous voltage, caution risk of electric shock, energy efficiency marking, protective earth, earth, caution hot surface, caution, operator's manual, stand-by, ON/OFF switch, fuse, recycling, etc.

WEEE Directive: This product is subject to the WEEE directive (2012/19/EU). Users can return the product to a recycling organization or retailer.

VCCI-A: This is a Class A product. In a domestic environment, it may cause radio interference, requiring user intervention.

BSMI Notice: Safety advice and precautions for use, including using original power adapters, cleaning instructions, moisture prevention, ventilation, and avoiding unauthorized disassembly.