RAB SLIM® Field-Adjustable Installation Instructions

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

⚠️ WARNING: Make certain power is OFF before installing the fixture. No user serviceable parts inside.

MOUNTING

To ensure weatherproof seal, apply weatherproof silicone sealant around the edge of the Housing, where it meets the wall, and/or Junction Box (by others) as shown in Figure 1. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.

1. Open fixture door using 2 Latches.
2. Tether Cable is provided for hands free wiring.
3. Open appropriate Knock-out Slots when mounting to Junction Box (by others) or Lag Bolts to mounting surface using locations shown in Figure 8 for SLIMXXS, SLIMXS, SLIMM, SLIML. Use Leveling Bubble to level fixture.
4. Make electrical connections as shown in wiring diagram (Figure 7). Use approved wiring connectors and wire to local NEC codes. Be careful not to pinch the wires.
5. Feed supply wires through Junction Box (by others). Check that the Gasket is properly placed.
6. Make sure Housing Gasket is properly seated. Close fixture door by 2 Latches. Silicone all Plugs and unused conduit entries.

Figure 1: Mounting Diagram Components

• Junction Box (by others)
• Gasket
• Latch (2)
• Leveling Bubble
• Housing Gasket
• Tether Cable
• Knock Out Slots
• Photocell Light Guide

FIELD ADJUSTMENT

Models: SLIMXXS, SLIMXS, SLIMS, SLIMM, SLIML (Bronze/White)

Photocell Operation: This product is equipped with a photocell. Photocell factory setting is set to the "OFF" position. To enable the Photocell "ON" feature, slide the center switch to the "ON" position (Figure 3). If the Photocell is set to the "ON" position and it is daylight, it may take up to 60-seconds for the light to turn off.

Color Temperature (CCT) Selection: This product is equipped with 5000K, 4000K or 3000K CCT color temperature selection. For maximum light output, use the 4000K Color Temperature.

Power (Wattage) Selection: SLIMXXS, SLIMXS, SLIMS, SLIMM, SLIML products are equipped with Power (W) output selection.

Follow instructions below to change Photocell ON/OFF operation, Color Temperature (CCT) and/or Power (W) from factory settings.

Factory Settings: 4000K / Photocell OFF

• SLIMXXS: 5W
• SLIMXS: 18W
• SLIMS: 28W
• SLIMM: 41W
• SLIML: 45W

1. Locate the selector switches inside the housing as shown in Figure 2.
2. Select Color Temperature (CCT), Power (W), and/or Photocell ON/OFF function by sliding the respective switch to the desired value (Figure 3).

Figure 2: Field-Adjustable Selector Switches

Figure 3: Selector Switch Detail

• Power (W) Selector Switch
• Photo Cell Selector Switch
• Color Temperature (CCT) Selector Switch

Models: SLIMXXSY, SLIMXSY, SLIMSY, SLIMMY, SLIMLY (Bronze/White) - 3000K Models Only

Photocell Operation: This product is equipped with a photocell. Photocell factory setting is set to the "OFF" position. To enable the Photocell "ON" feature, slide the center switch to the "ON" position (Figure 3). If the Photocell is set to the "ON" position and it is daylight, it may take up to 60-seconds for the light to turn off.

Power (Wattage) Selection: SLIMXXSY, SLIMXSY, SLIMSY, SLIMMY, SLIMLY products are equipped with Power (W) output selection.

Follow instructions below to change Photocell ON/OFF operation, and/or Power (W) from factory settings.

Factory Settings: Photocell OFF

• SLIMXXSY: 5W
• SLIMXSY: 18W
• SLIMSY: 28W
• SLIMMY: 41W
• SLIMLY: 45W

1. Locate the selector switches inside the housing as shown in Figure 2.
2. Select Power (W) and/or Photocell ON/OFF function by sliding the respective switch to the desired value (Figure 4).

Figure 4: Selector Switch Detail (3000K Models)

OPTIC ANGLE ADJUSTMENT

Follow instructions below to change Optic Angle. Selectable options are 0°/10°/20°.

Factory Settings: 0°

1. Locate Optic Angle Selector on the Side of Housing as shown in Figure 5.
2. Use a Phillips head screwdriver to select desired Optic Angle (Figure 6).

Figure 5: Housing with Optic Angle Selector Location

Figure 6: Optic Angle Selector Detail

0-10V DIMMABLE WIRING

Universal voltage driver permits operation at 120V through 277V, 50 or 60 Hz. For 0-10V dimming, follow the wiring directions as shown in Figure 7.

1. Connect the black fixture lead to the LINE supply lead.
2. Connect the white fixture lead to the COMMON supply lead.
3. Connect the GROUND wire from fixture to supply ground.
4. Connect the purple fixture lead to the (V+) DIM lead.
5. Connect the pink fixture lead to the (V-) DIM lead.
6. Cap the yellow fixture lead, if present. Do NOT connect.

NOTE: Do not connect DIM V+ (purple)/ DIM V- (pink) to line voltage or supply ground.

Figure 7: 0-10V Dimmable Wiring Diagram

• LINE (BLACK)
• COMMON (WHITE)
• (+) DIM V (PURPLE)
• (-) DIM V (PINK)
• Vaux 12V (YELLOW)
• GROUND (GREEN)
• LIGHT FIXTURE

TROUBLESHOOTING

1. Check that the line voltage at fixture is correct. Refer to wiring directions.
2. Is the fixture grounded properly?
3. Be sure the photocell, if used, is functioning properly.

CLEANING

CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.

1. Clean Lens with non-abrasive glass cleaning solution.
2. Do not open the fixture to clean the LED. Do not touch the LED.

LAG BOLT MOUNTING LOCATIONS

Figure 8: Mounting Hole Patterns for SLIM Models

SLIMXXS, SLIMXS

Dimensions: 4-5/16" (110mm) width, 2-3/16" (55mm) height. Features Lag Bolt Locations and GND connection.

SLIMS

Dimensions: 6-3/4" (172mm) width, 5-1/8" (130mm) height. Features Lag Bolt Locations and GND connection.

SLIMM

Dimensions: 11-13/16" (300mm) width, 5-1/8" (130mm) height. Features Lag Bolt Locations and GND connection.

SLIML

Dimensions: 14-13/16" (376mm) width, 5-1/8" (130mm) height. Features Lag Bolt Locations and GND connection.