RAB X34 Field-Adjustable LED Installation Instructions

Knuckle Mount

To ensure a weatherproof seal, apply weatherproof silicone sealant around the edge of the junction box (provided by others). This is especially important with an uneven surface.

1. Secure the fixture to a 1/2" NPS hole in the junction box or landscape post. Seal the arm thread using Teflon® tape or silicone sealant. (Refer to Figure 1 for visual guide).
2. The X34 swivel arm allows 180° of vertical aiming adjustment depending on the mounting position. (Refer to Figure 2 for visual guide).

Figure 1 Description: Shows the fixture base (Knuckle Mount) attaching to a junction box via a 1/2" NPS hole.

Figure 2 Description: Illustrates the fixture's swivel arm, indicating 180° of vertical adjustment.

Slipfitter Mounting

The slipfitter mounting fits a 2 3/8" O.D. Tenon. Place the slipfitter over the Tenon and secure the fixture with two (2) Set Screws on the side of the Slipfitter. (Refer to Figure 1 for visual guide).

1. Loosen the Locking Bolt and swivel the fixture to the desired angle. (Refer to Figure 2 for visual guide).
2. Tighten the Locking Bolt.

Figure 1 Description: Shows the slipfitter mounting hardware, including Set Screws and a Tenon.

Figure 2 Description: Illustrates loosening the Locking Bolt to adjust the fixture's angle.

Trunnion Mounting

CAUTION: Use a UL certified liquid-tight cord grip suitable for use with three-conductor-type STW flexible cord for connection to a wet location outlet box (provided by others).

To adjust the angle of the fixture using the Trunnion:

1. Loosen the Pivot Bolts & Angle Locking Screw. (Refer to Figure 3 for visual guide).
2. Adjust fixture to the desired angle.
3. Tighten Pivot Bolts & Angle Locking Screw.

Figure 3 Description: Shows the Trunnion mounting hardware, including Pivot Bolts and an Angle Locking Screw.

Photocell Operation

This product is equipped with a photocell (except /RGB models). The factory setting is "OFF".

• To enable the photocell "ON" feature, slide the center switch to the "ON" position. (Refer to Figure 5 for visual guide).
• If the photocell is set to "ON" and it is daylight, it may take up to 60 seconds for the light to turn off.

Figure 5 Description: Illustrates the selector switches on the side of the housing, including a switch for Photocell (ON/OFF).

Color Temperature (CCT) Selection

This product is equipped with 5000K, 4000K, or 3000K CCT selection. For maximum light output, use the 4000K CCT setting.

Power Selection

• X34L: Equipped with 90W/80W/70W power output selection.
• X34XL: Equipped with 130W/110W/95W power output selection.
• X34XXL: Equipped with 160W/140W/120W power output selection.

Note: /RGB models can use the Lightcloud Blue mobile app to adjust colors between 2200K-6500K or 16+ million colors. /RGB models output can also be adjusted using the Lightcloud Blue mobile app.

Note: Field adjustment instructions do not apply to /RGB models.

Factory Settings (for non-RGB): Maximum Power, 4000K CCT, Photocell/OFF.

Standard Wiring

Connect the fixture leads to the supply leads as shown in Figure 5.

• Connect the black fixture lead to the LINE supply lead.
• Connect the white fixture lead to the COMMON supply lead.
• Connect the GROUND wire from the fixture to the supply ground.

Figure 5 Description: A wiring diagram showing LINE (BLACK), COMMON (WHITE), and GROUND connections for the LIGHT FIXTURE.

0-10V Dimmable Wiring

Universal voltage driver permits operation at 120V through 277V, 50 or 60 Hz. For 0-10 dimming, follow the wiring directions as shown in Figure 6.

• Connect the black fixture lead to the LINE supply lead.
• Connect the white fixture lead to the COMMON supply lead.
• Connect the GROUND wire from fixture to supply ground. Do NOT connect the GROUND of the dimming fixture to the output.
• Connect the purple fixture lead to the DIM V+ lead.
• Connect the pink fixture lead to the DIM V- lead.
• Internal 12V (aux) wire is capped; DO NOT CONNECT.

Note: /RGB models will not have 0-10V (purple DIM V+ and pink DIM V-) leads.

Figure 6 Description: A wiring diagram showing connections for 0-10V dimming: LINE (BLACK), COMMON (WHITE), (+) DIM V (PURPLE), (-) DIM V (PINK), Vaux 12V (WHITE), and GROUND.

Resetting to Factory Settings

If your Lightcloud Blue fixture is already paired, reset it to factory settings using one of the following methods:

• Method 1: Delete from App
  Open the app, access the device settings for the paired device, ensure the fixture is online (green status bars visible), and select "Delete".
• Method 2: Reset Button
  Press and release the Reset Button located on the fixture. (Visuals show button location on X34 RGB S/M and X34 RGB L/XXL models).

Adjusting RGB Colors

To access the RGB color wheel, select the chevron [select color wheel] to the right of the CCT slider bar and select RGB. You can add up to 10 favorite colors per device or Area. Once a color is defined, press the back button [return to previous screen] in the top left.

Configuration

To configure Lightcloud Blue, log in to the Lightcloud Blue app. For additional startup information, visit www.lightcloud.com/item/lcb-getting-started/.

Controlling Lightcloud Blue Device

1. Confirm your device is powered on.
2. Download the Lightcloud Blue app from the Apple App Store or Google Play Store.
3. Launch the App and create an account or log in.
4. Tap the "add device" icon in the app to start connecting devices.
5. Create Areas, Scenes, and Schedules to organize and control your devices.
6. You're all set!

For additional information about the Lightcloud Blue mobile app, visit www.lightcloud.com/item/lcb-getting-started/.