BIGBIG WON Rainbow Lite Gamepad

01. Component Illustration

This section provides a detailed illustration of the BIGBIG WON Rainbow Lite gamepad components.

Gamepad Layout:

• Top Buttons: LT (Left Trigger), LB (Left Bumper), RT (Right Trigger), RB (Right Bumper), A/B/X/Y face buttons, Triangle button, View button (Botão Vista), Menu button (Botão Menu).
• Joysticks: Left joystick (LS), Right joystick (RS).
• Directional Pad (D-pad): For directional inputs.
• Central Buttons: HOME button, USB Interface port.
• Rear Buttons: M1 and M2 programmable back buttons, FN (Function) button.
• Ports: 3.5mm audio port for headphones/microphone.
• Indicators: Mode indicator light, LED1, LED2, LED3, LED4 (used for status and feedback).

Package Contents and Supported Platforms:

02. Connection

The Rainbow Lite is a wired controller requiring a Type-C cable to connect to the main unit.

Note: The gamepad supports both Xinput and Switch modes. After connecting, switch to the corresponding mode for normal use. PC platforms require Xinput mode, while Switch platforms require Switch mode. Xinput is the default mode.

• For Steam: Ensure "XBOX Controller Configuration Support" is enabled in the software's "Settings - Controller - General Controller Settings" to ensure proper recognition in games.
• For Switch: Navigate to "Settings - Gamepad & Sensor - Wired Gamepad Connection" on the Switch console.

03. Mode Switching

To use the gamepad correctly, switch between Xinput and Switch modes after connection as follows:

• To switch to Switch mode: Press and hold the A + HOME buttons for 3 seconds until the mode indicator light turns red.
• To switch to Xinput mode: Press and hold the B + HOME buttons for 3 seconds until the mode indicator light turns green.

04. Light Effect

The gamepad features various built-in light effects. Double-press the FN button to activate or deactivate these effects.

05. Button Mapping

The gamepad includes two expandable back buttons (M1/M2) and supports the following button mapping configurations:

• Define Mapping: Press FN + (M1/M2). The mode indicator light will breathe green, indicating the button mapping state. Then, press the front button you wish to map to M1/M2. The mode indicator light will flash green twice to confirm successful mapping.
• Clear Mapping: Press and hold the button whose mapping you want to clear (M1/M2). Double-click the FN button. The mode indicator light will flash green to confirm that the mapping for that button has been successfully cleared.

06. Turbo Function

The gamepad supports button turbo functionality. The eight supported buttons are A/B/X/Y, D-pad directions (Up/Down/Left/Right), LT/RT/LB/RB. The definition is as follows:

• Define Turbo: Press and hold FN + [desired button]. The mode indicator light will flash orange to indicate successful activation. When a turbo function is triggered, LEDs 2 and 3 will flash according to the turbo frequency.
• Clear Turbo: Press and hold the button whose turbo function you want to clear. Double-click the FN button. The mode indicator light will flash orange to confirm that the turbo function for that button has been successfully cleared.
• Turbo Frequency: Press and hold FN + [arrow key, likely right arrow based on context] to cycle through frequencies of 5/s, 10/s, and 20/s. The default value is 5/s.

07. Macro Recording

This gamepad supports macro recording. Each macro set must be assigned to a back button (M1/M2) as a trigger. Supported buttons for recording include A/B/X/Y, D-pad directions (Up/Down/Left/Right), LT/RT/LB/RB, RS/LS, and the eight joystick directions.

• Record Macro: Press and hold FN + (M1/M2) for 3 seconds. The mode indicator light will breathe red, indicating macro recording is in progress. Press the gamepad buttons to record the macro sequence. Click FN when recording is complete; the mode indicator light will flash red twice to end the recording. During macro execution, the four LEDs will flash from left to right until the macro finishes.
• Clear Macro: Double-click the back button (M1/M2) for which you want to clear the macro. The mode indicator light will flash red to confirm that the macro configuration for this button has been successfully cleared.

08. Joystick Dead Zone Adjustment

The joystick has a default factory dead zone. Users requiring a 0 dead zone can press FN + Left/Right Joystick Down (LS/RS) to toggle the dead zone between 0 and 10 for the left and right joysticks, respectively.

Note: A joystick with 0 dead zone offers higher control precision but may result in input drift in games that do not compensate for zero dead zones.

09. Quick Trigger

The gamepad supports a quick trigger configuration designed to optimize linear trigger clicks. A quick trigger setting allows the trigger to register a "release" at any point after being pressed and can be pressed again without returning to its original position, optimizing rapid click rates.

• Activate/Deactivate Quick Trigger: Press and hold the Triangle button + Trigger (LT/RT). The mode indicator light will flash cyan twice to confirm successful activation. Press and hold the Triangle button + Trigger (LT/RT) again. The mode indicator light will flash green and then twice to confirm deactivation.

10. Joystick/Trigger Calibration

If you experience severe joystick drift, cannot reach maximum trigger values, or triggers output values automatically without being pressed, calibrate the joystick and triggers as follows:

1. Press and hold the View button + Menu button simultaneously for 3 seconds. The four LEDs will breathe slowly.
2. Push the joysticks to their limits and rotate them in a uniform circle, repeating 3-5 times for each.
3. Press the LT/RT buttons to their limit and release, repeating 3-5 times.
4. Finally, press the View button + Menu button simultaneously. The LEDs will flash twice and then turn off, indicating that calibration is complete.

11. Screenshot

The gamepad supports one-touch screenshots. In Xinput and Switch modes, clicking the Triangle button functions as a screenshot button. (Screenshot files for PC are saved in "This PC - Pictures - Screenshots").

12. Audio

The gamepad supports audio input/output. After connecting to the main unit, plug your headset with a microphone into the 3.5mm audio port located on the bottom of the gamepad.

The main unit's volume can also be adjusted using the button combination FN + Up/Down arrow keys (volume adjustment is only available on PC).

13. Vibration Adjustment

The gamepad supports four levels of vibration adjustment. Press FN + Right arrow key to cycle through vibration levels: Strong, Medium, Weak, and Off.

14. One-Click Reset

Press and hold the HOME button for 10 seconds until the gamepad vibrates, indicating that the reset configuration is successful.

15. Detailed Operating Instructions

For video tutorials, please visit the official support website: Moojiang Official Support Site: https://www.bigbigwon.com/support

16. Your Rights

12 months limited warranty from the date of purchase.

Support and Resources

Get video tutorials, firmware updates, and e-manuals from the BIGBIG WON support site.

Visit: https://www.bigbigwon.com/support