RAINBOW Lite Controller

01. DIAGRAMA DE COMPONENTES

The RAINBOW Lite controller features a symmetrical design with two analog joysticks (Left and Right), a D-pad, A/B/X/Y buttons, LT/RT/LB/RB shoulder buttons, Menu, View, FN, M1, and M2 function buttons, and a HOME button. It includes LED indicators (LED1, LED2, LED3, LED4) and a HOME Light. Connectivity is via a USB Type-C port and a 3.5mm headphone jack.

02. CONEXIÓN

The controller is a wired controller, connecting to the host with a Type-C data cable. The controller supports two modes: Xinput and Switch. After connection, you must switch to the corresponding mode for normal operation. For PC platforms, switch to Xinput mode. For Switch platforms, switch to Switch mode. Xinput mode is the default.

Steam: For connection to the Steam platform, you must enable "XBOX Configuration Support" in the software's "Settings-Controller-General Controller Settings". Otherwise, you may encounter identification issues in games.

Switch: After connecting to Switch, you must enable "Settings-Controller and Sensor-Wired Connection of Pro Controller" in the Switch's system settings.

03. CAMBIO DE MODOS

This controller is compatible with Switch and Xinput modes. After connecting, you must switch to the corresponding mode for correct usage. The configuration methods are as follows:

• Hold the A + HOME keys for 3 seconds until the HOME light turns red, indicating Switch mode.
• Hold the B + HOME keys for 3 seconds until the HOME light turns green, indicating Xinput mode.

04. EFECTO DE ILUMINACIÓN

This controller has a variety of built-in lighting effects. Double-click the FN key to toggle lighting effects on and off.

05. MAPEO

The controller comes with two backup expansion keys (M1/M2) and supports key mapping configuration. The process is as follows:

Set Mapping: Hold FN + (M1/M2). The green indicator light will flash from bright to dim, indicating entry into mapping state. Press the front key you wish to map to M1/M2 again. The green indicator light will flash, signifying successful mapping.

Clear Mapping: Hold the "Key to cancel mapping (M1/M2)" key, then double-click FN. The green indicator light will flash twice, indicating that the mapping configuration for the current key has been cleared.

06. COMBOS

The controller supports key combo configuration. A total of 8 keys are compatible: A/B/X/Y/LT/RT/LB/RB. The configuration is as follows:

Set Combos: Hold FN + "Key to set combos". The orange indicator light will flash twice, indicating successful activation. When combos are active, LED 2 and LED 3 will flash at the current combo frequency.

Clear Combos: Hold the "Key to cancel combos" key, then double-click FN. The orange indicator light will flash twice, indicating that the combo configuration for the current key has been cleared.

Combo Frequency: Hold FN + ↑/↓ to cycle through three frequencies: 5/s, 10/s, and 20/s. The default frequency is 5/s.

07. GRABACIÓN MACRO

The controller supports macro recording. Each macro must be linked to a backup key (M1/M2) as a trigger switch. The keys that support macro recording are A/B/X/Y, D-pad directions (↑/↓/←/→), L/R/ZL/ZR, RS/LS, and the eight joystick directions.

Macro Recording: Hold FN + (M1/M2) for 3 seconds. The red indicator light will change from bright to dim, indicating entry into macro recording state. Press the console key to record the macro, and click FN once recording is complete. The red indicator light will flash twice, signifying that recording has finished. During macro execution, the four LED lights will flash slowly from left to right until macro execution is complete.

Clear Macro: Hold the "Key to cancel macro (M1/M2)" key, then double-click FN. The red indicator light will flash twice, indicating that the macro configuration for the current key has been cleared.

08. CAMBIO DE ZONA MUERTA CON JOYSTICK

This controller has a default factory dead zone setting for the joystick. Users who wish to adjust this can press FN + Left and Right joysticks down (LS/RS) to switch between 0/10 dead zone modes for the left and right joysticks, respectively.

Attention: A joystick dead zone of 0 allows for greater control precision but may also cause slight drift in games that do not have built-in dead zones.

09. TRIGGER RÁPIDO

The controller supports quick trigger configuration, which optimizes the rapid clicking of linear triggers. With quick trigger configured, the trigger is considered "off" after being pressed at any distance, without needing to be released to the original position to activate again. This can significantly optimize rapid click speed.

Enable/Disable Quick Trigger: Hold the X + Trigger (LT/RT) keys. The turquoise mode indicator light will flash twice, indicating successful "quick trigger" configuration. Press the X + Trigger (LT/RT) keys again. The turquoise mode indicator light will flash twice again, indicating successful "quick trigger" disabling.

Quick trigger configuration only supports enabling and disabling. After downloading the companion app, it also supports adjusting the left and right trigger travel and the front and rear dead zones.

10. CALIBRACIÓN DE JOYSTICK Y TRIGGER

If the joystick drifts significantly, the maximum downward value cannot be modified, or the trigger automatically sends a value and cannot reach the maximum linear value, you can attempt to calibrate the joystick and trigger.

Operation Method:

1. Hold the View + Menu keys simultaneously for 3 seconds. The four LED indicator lights will flash slowly from bright to dim.
2. Push the joystick to its limit and rotate it at a constant speed. Repeat this operation 3 to 5 times.
3. Then, press the LT/RT keys to their limit and release them. Repeat 3-5 times.
4. Finally, press the View + Menu keys simultaneously. The LED indicator light will flash twice and then turn off, indicating that calibration is complete.

11. CAPTURA

This controller supports one-key screenshot capture. In both Xinput and Switch modes, press the X key for a screenshot. (The screenshot file on PC platforms is saved in "This Computer-Pictures-Screenshots")

12. AUDIO

The controller supports audio input/output. After connecting to the host, insert headphones with a microphone into the 3.5mm audio port on the bottom of the controller. Additionally, you can adjust the host's volume using the key combination FN + ↑/↓ (volume adjustment function is only available for PC).

13. AJUSTE DE VIBRACIÓN

The controller supports four-speed vibration adjustment. Press FN + ↓ to cycle through the four vibration modes: strong, medium, weak, and off.

14. CONFIGURACIÓN DE RESTABLECIMIENTO POR UNA TECLA

Hold the HOME key for 10 seconds until the controller vibrates, indicating successful reset.

15. INSTRUCCIONES DE OPERACIÓN DE LAS FUNCIONES

Visit the official website for video guides: BIGBIG WON official website support page https://www.bigbigwon.com/support

16. SUS DERECHOS

You have the right to enjoy a 12-month warranty starting from the date of purchase.