Aero One
Front I/O Panel Cable Connection
The front panel connectors include buttons for Reset and Power, LEDs for Hard Drive Activity (HDD LED) and Power (Power LED +/-), an HD Audio connector, and a USB 3.0 connector. These connect to corresponding headers on the motherboard. Please refer to your motherboard's manual for precise pin assignments. Note: Specifications may vary depending on your region. Contact your local retailer for more information.
Accessory Bag Contents
- Motherboard Screws (4x)
- Motherboard Standoffs (5x)
- HDD Screws (3x)
- SSD Screws (1x)
- Fan Screws (multiple)
- Cable Ties (multiple)
How to Install Guide
1. Install Motherboard
Place the motherboard inside the PC case, aligning it with the pre-installed standoffs. Secure the motherboard using the provided Motherboard Screws. Connect the front panel connectors (F-PANEL) from the case to the appropriate headers on the motherboard, such as Power Switch, Reset Switch, HDD LED, and Power LED.
2. Install PSU
Install the PSU (Power Supply Unit): Slide the PSU into its designated bay, typically located at the bottom rear of the case. Secure the PSU using the provided PSU Screws.
3. Install Add-on Card
Remove the corresponding expansion slot cover(s) on the rear of the case. Align the add-on card (e.g., graphics card, network card) with an available PCIe slot on the motherboard and press down firmly until it clicks into place. Secure the card to the case using the PCI Screws.
4. Install 3.5" HDD
Mount the 3.5" Hard Disk Drive into a designated drive bay or bracket. Secure the HDD using the provided HDD Screws. Slide the drive into its bay until it is firmly seated.
5. Install 2.5" SSD
Mount the 2.5" Solid State Drive into its designated mounting location, often a bracket or tray behind the motherboard tray. Secure the SSD using the provided SSD Screws.
6. Install Radiator
6a. Install Front Radiator: Mount a radiator (if applicable) to the front of the case. Ensure proper orientation for airflow and secure it using screws.
6b. Install Top Radiator: Mount a radiator (if applicable) to the top of the case. Secure it using screws.
6c. Install Rear Radiator/Fan: Mount a fan or small radiator to the rear exhaust position of the case. Secure it using screws.
7. Install Fans
7a. Install Front Fans: Attach fans to the front mounting points of the case. Secure them using Fan Screws.
7b. Install Top Fans: Attach fans to the top mounting points of the case. Secure them using Fan Screws.
7c. Install Rear Fan: Attach a fan to the rear mounting point of the case. Secure it using Fan Screws.
7d. Install PSU Shroud Fan: Mount a fan in the PSU shroud area for additional airflow, if applicable. Secure it using screws.
I/O Panel
The rear I/O panel provides connectivity for USB 3.0 devices, HD Audio and microphone inputs, a system reset button, and a power button.
RGB Fan Hub (H66C)
Connection Set Up User Guide
The RGB Fan Hub (H66C) manages RGB lighting synchronization. It features connectors for Addressable RGB devices, SATA power from the PSU, fan headers, and connections for the case's Power and Reset buttons, as well as front panel USB 3.0 and HD Audio.
For ASUS Aura Sync, MSI Mystic Light Sync, and GIGABYTE RGB Fusion Motherboards:
- Connect (A) to the motherboard's PWM fan header.
- Connect (B) or (D) to the motherboard's Addressable RGB header (depending on motherboard brand/type).
- Connect (C) to a SATA power connector from the PSU.
For GIGABYTE RGB Fusion Motherboards:
- Connect (A) to the motherboard's PWM fan header.
- Connect (D) to the motherboard's Addressable RGB header.
- Connect (C) to a SATA power connector from the PSU.
For Non-Addressable RGB Motherboards:
- Connect (A) to the motherboard's PWM fan header.
- Connect the 2-pin reset switch connector (E) to the hub.
- Connect (C) to a SATA power connector from the PSU.
- Use the RGB fan connectors (F) to connect RGB fans to the hub.
Reset Button Functionality:
- Normal use: Acts as the motherboard's reset button if connected to the hub.
- LED Control: Hold for 3 seconds ? to switch between motherboard and button control for LEDs. Hold Reset for 6 seconds to turn off LEDs, press once to turn them back on.
