Introduction
This manual provides instructions for the SilverStone ICEGEM series of high-performance all-in-one liquid coolers, including models ICEGEM 240P, ICEGEM 280, and ICEGEM 360. It covers accessory identification, installation procedures for various CPU sockets, and the operation of the ARGB controller.
Accessories
Please verify that you have all the following accessories before proceeding with the installation:
- A FAN SCREW x8: Quantity x12 (for 240P/280 models) or x12 (for 360 model). Used for mounting fans to the radiator.
- B CASE SCREW x8: Quantity x12 (for 240P/280 models) or x12 (for 360 model). Used for mounting the radiator to the computer case.
- C PLASTIC SPACER: Quantity x4. Used as part of the mounting bracket assembly for Intel and AMD sockets.
- D M3.5*30mm SCREW: Quantity x4. Used for securing the cooler assembly to the mounting brackets.
- E AMD SPACER: Quantity x1. Specific spacer for AMD socket installations.
- F SPRING SCREW: Quantity x4. Used in various mounting configurations.
- G STAND-OFF: Quantity x4. Used to create space between the motherboard and the mounting hardware.
- H THERMAL GREASE: Quantity x1. Pre-applied or to be applied to the CPU for optimal heat transfer.
- I BACK PLATE: Quantity x1. Used behind the motherboard for support during installation.
- J AM4/AM3 CLIP: Quantity x1. Specific clip for AMD AM4/AM3 socket installations.
- K TR4 CLIP: Quantity x1. Specific clip for AMD sTRX4/TR4 socket installations.
- L LGA2011 SCREW: Quantity x4. Specific screws for Intel LGA 2011/2066 sockets.
- M TR4 SCREW: Quantity x4. Specific screws for AMD sTRX4/TR4 socket installations.
- N 2 IN 1 FAN CABLE: Quantity x1 (for 240/280 models). Connects two fans to a single header.
- O 3 IN 1 FAN CABLE: Quantity x1 (for 360 model). Connects three fans to a single header.
- P 4PIN PERIPHERAL ADAPTER CABLE: Quantity x1. For connecting to power supply units or other peripherals.
- Q ARGB CONTROL BOX: Quantity x1. Manages ARGB lighting effects.
- R MOTHERBOARD SYNC CABLE: Quantity x1. Connects the ARGB controller to the motherboard for synchronization.
- S SATA POWER ADAPTER: Quantity x1. Connects the ARGB controller to the PSU for power.
- 2 IN 1 ARGB CABLE: Quantity x1. For connecting ARGB devices.
Installation Guide
Fan and Radiator Installation
This section details the mounting of fans to the radiator and the radiator assembly to the computer case.
For ICEGEM 240P/280 Models:
- Attach two fans to the radiator using A FAN SCREW x8. The diagram shows screws passing through the fan frame into the radiator fins.
- Mount the radiator assembly into the computer case using B CASE SCREW x8. The diagram illustrates securing the radiator to the case's mounting points.
- Connect the fan cables using the N 2 IN 1 FAN CABLE. The diagram shows connecting two fan cables to this splitter, which then connects to the CPU_FAN header on the motherboard.
For ICEGEM 360 Model:
- Attach three fans to the radiator using A FAN SCREW x8.
- Mount the radiator assembly into the computer case using B CASE SCREW x8.
- Connect the fan cables using the O 3 IN 1 FAN CABLE. The diagram shows connecting three fan cables to this splitter, which then connects to the CPU_FAN header on the motherboard.
Intel Socket Installation
Follow these steps for Intel LGA 115x, 1366, 2011, and 2066 sockets.
LGA 115x / 1366 Installation
The diagrams illustrate the following steps:
- Place the I BACK PLATE behind the motherboard, aligning its holes with the CPU socket mounting points.
- Attach the C PLASTIC SPACER to the backplate for each mounting point.
- Install the G STAND-OFFs onto the plastic spacers.
- Position the cooler's mounting bracket assembly over the CPU socket. The diagram shows a "ROTATE TO ALIGN" step for proper orientation.
- Secure the mounting bracket to the stand-offs using D M3.5*30mm SCREW x4.
- Apply thermal grease H to the CPU (if not pre-applied).
- Remove any protective film from the cooler's water block base.
- Mount the cooler assembly onto the CPU and secure it by screwing it into the mounting bracket. The diagram shows a "Press" action indicating firm attachment.
LGA 2011 / 2066 Installation
The diagrams illustrate the following steps:
- Place the I BACK PLATE behind the motherboard.
- Attach the G STAND-OFFs to the motherboard.
- Position the cooler's mounting bracket assembly over the CPU socket.
- Secure the mounting bracket to the stand-offs using L LGA2011 SCREW x4.
- Apply thermal grease H to the CPU.
- Mount the cooler assembly onto the CPU and secure it. The diagram shows a "Press" action.
AMD Socket Installation
Follow these steps for AMD AM4, AM3/AM2, sTRX4, and TR4 sockets.
AM4 / AM3 / AM2 Installation
The diagrams illustrate the following steps:
- Place the I BACK PLATE behind the motherboard.
- Attach the E AMD SPACER to the backplate.
- Install the G STAND-OFFs onto the AMD spacers.
- Position the cooler's mounting bracket assembly over the CPU socket. The diagram shows a "ROTATE TO ALIGN" step for proper orientation.
- Secure the mounting bracket to the stand-offs using D M3.5*30mm SCREW x4.
- Alternatively, for AM4/AM3, use the J AM4/AM3 CLIP and F SPRING SCREW x4 to secure the bracket.
- Apply thermal grease H to the CPU.
- Mount the cooler assembly onto the CPU and secure it. The diagram shows a "Press" action.
sTRX4 / TR4 Installation
The diagrams illustrate the following steps:
- Attach the K TR4 CLIP to the motherboard mounting points.
- Install the F SPRING SCREW x4 into the clip.
- Mount the cooler assembly onto the CPU. The diagram shows securing it using M TR4 SCREW x4.
- Apply thermal grease H to the CPU.
ARGB Controller
This section details the connection and operation of the ARGB controller for customizable lighting effects.
Connections
The ARGB controller system involves connecting the controller box to the motherboard, power supply, and fans.
- ARGB Control Box (Q): This is the central unit for managing ARGB lighting. It has ports for VDG and +5V D GND signals.
- Motherboard Sync Cable (R): Connects the ARGB Control Box to the motherboard's ARGB header. The diagram shows compatibility with headers labeled MB(ASUS/MSI/ASRock/BIOSTAR) and MB(GIGABYTE). Ensure correct pin alignment (+5V, D, GND, VDG).
- SATA Power Adapter (S): Connects the ARGB Control Box to the Power Supply Unit (PSU) via a SATA power connector for power.
- 4PIN PERIPHERAL ADAPTER CABLE (P): This cable is used to connect the ARGB Control Box to the PSU for power, or potentially to other devices. The diagram shows it connecting to the PSU.
The diagram illustrates the ARGB Control Box receiving power from the PSU via the SATA adapter and receiving lighting control signals from the motherboard via the sync cable. It also shows the fan connections to the ARGB Control Box.
User Manual
The ARGB controller features three buttons: [+], [-], and [M] (Mode).
- Button Functions:
- [M] Button: Press to cycle through lighting effect mode, lighting speed mode, brightness mode, and demo mode.
- [+] / [-] Buttons: Use these buttons to adjust the selected level (e.g., speed, brightness) within the current mode.
- Power On/Off:
- Press and hold the [M] button for 3 seconds to turn off the ARGB lighting.
- Press the [M] button again to turn it back on, resuming the last set lighting effect mode and level.
- Default Settings:
- When powered on for the first time, the default lighting effect is "Rainbow".
- If the controller is turned off or loses power, it will resume to the last set lighting effect mode and level upon power restoration.
- Press and hold the [-] button for 3 seconds in any mode to reset to the default effect (Rainbow).
- Lighting Effect Modes:
- Rainbow (Default)
- Breathing
- Flashing
- Layering (8 colors: white, indigo, violet, yellow, blue, red, green, orange)
- Flowing
- 256 Colors Auto Switching (Cycles through 8 colors: white, indigo, violet, yellow, blue, red, green, orange)
- Press [+] for 3 seconds to lock the currently displayed color.
- Press [-] for 3 seconds to unlock the color and resume auto-switching.
- Radar
- Color Layering, Red
- Color Layering, Green
- Color Layering, Blue
- Mode Switching and Adjustment:
- Press [M] to switch between modes.
- Speed Adjustment: When the controller's red indicator light is on, press [+] or [-] to adjust lighting speed (fast/slow).
- Brightness Adjustment: When the controller's blue indicator light is on, press [+] or [-] to adjust brightness.
- Demo Mode: When the controller's yellow indicator light is on, it will display and cycle through all 10 lighting effects continuously.
