SilverStone Nitrogon Series NT09-115X

Product Overview

SilverStone Technology's Nitrogon NT09-115X is a slim profile CPU cooler designed for space-limited applications that utilize LGA 1156/1155/1150/1151 platforms. It features extruded aluminum fins for excellent thermal conductivity. The NT09-115X is equipped with a custom PWM 92mm silent fan that is staggered against the aluminum fins for better airflow focus and enhanced heat dissipation. Measuring only 45mm tall, the NT09-115X is a premier choice for slim cases utilizing LGA 1156/1155/1150/1151 processors.

Key Features

• Supports Intel LGA1156/1155/1150/1151 processors
• Designed for low profile systems at only 45mm tall
• Custom quiet 92mm fan for excellent cooling and low noise
• Extruded aluminum fins for good heat dissipation
• Reinforced back plate design reduces motherboard bending to provide tighter CPU contact
• Rated for 65W TDP

Specifications

Installation Guide

1. Step 1: Install the included back-plate onto the backside of the motherboard.

   Diagram Description: Shows a back-plate being placed on the rear of a motherboard.

2. Step 2: Place the NT09-115X cooler on top of the installed CPU and align the four spring screws with the holes on the motherboard.

   Diagram Description: Shows the CPU cooler being positioned over the CPU, with arrows indicating alignment of screws with motherboard holes.

3. Step 3: Press and fasten two screws in position A as shown, and then the other two in position B to fix the CPU cooler in place.

   Diagram Description: Illustrates tightening screws in sequence at points A and B to secure the cooler.

4. Step 4: When the NT09-115X is installed, connect the CPU fan cable to the motherboard fan header for CPU.

   Diagram Description: Shows the CPU fan cable being plugged into the motherboard's CPU fan header.

Removal Guide

1. Step 1: Remove the CPU fan cable from the motherboard fan header.

   Diagram Description: Shows the CPU fan cable being disconnected from the motherboard header.

2. Step 2: Loosen and pull up two screws in position A, and then the other two in position B to remove the CPU Cooler from the motherboard.

   Diagram Description: Illustrates loosening screws at points A and B to detach the cooler.

3. Step 3: Remove the CPU cooler from the motherboard.

   Diagram Description: Shows the CPU cooler being lifted off the motherboard.

4. Step 4: Remove the back-plate from the motherboard.

   Diagram Description: Shows the back-plate being removed from the rear of the motherboard.

Warranty and Contact Information

This product has a limited 3-year warranty in North America, Europe, and Australia. For information on warranty periods in other regions, please contact your reseller or SilverStone authorized distributor.

Warranty Terms & Conditions

• Defects or damages resulting from defective production are covered under warranty.
• Conditions covered include: usage in accordance with instructions, no misuse or overuse, no damage from natural disasters (e.g., thunder, fire, earthquake, flood, salt, wind, insects, animals), no disassembly or modification, and intact warranty marks/stickers.
• Loss or damages resulting from conditions other than those listed are not covered.
• SilverStone Technology's maximum liability under warranty is limited to the current market value of the product (depreciated value, excluding shipping, handling, and other fees).
• SilverStone Technology is not responsible for other damages or loss associated with the use of the product, including but not limited to loss of data, business, profits, or incidental/consequential damages.
• Warranty covers only the original purchaser through authorized SilverStone distributors and resellers and is not transferable.
• Proof of original purchase (dated itemized receipt or invoice) is required to determine warranty eligibility.
• For warranty service, contact your retailer, reseller, or SilverStone authorized distributors. More information is available at www.silverstonetek.com.
• Customers must provide proof of purchase, bear the cost of shipping the product to SilverStone authorized distributors, and obtain a Return Merchandise Authorization ("RMA") number before sending the product. SilverStone authorized distributors will bear the cost of shipping the product back after service.
• Updated warranty information is posted on SilverStone's official website; visit www.silverstonetek.com for the latest updates.

Additional Info & Contacts

• North America: Email usasupport@silverstonetek.com. SilverStone Technology in North America may repair or replace defective products with functionally tested refurbished products. Replacement products are warranted for the remainder of the warranty period or thirty days, whichever is longer. For returns within 30 days of purchase, contact the place of purchase. After 30 days, customers must initiate an RMA procedure with SilverStone Technology in USA by downloading the "USA RMA form for end-users" from http://silverstonetek.com/contactus.php and following its instructions.
• Australia: Email support@silverstonetek.com. Goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if they fail to be of acceptable quality and the failure does not amount to a major failure.
• Europe: Email support.eu@silverstonetek.de
• All other regions: Email support@silverstonetek.com

SilverStone Technology Co., Ltd. 12F No. 168 Jiankang Rd., Zhonghe Dist., New Taipei City 235 Taiwan R.O.C. + 886-2-8228-1238 (standard international call charges apply)

All trademarks are registered to their respective owners. ©2015 SilverStonetek Co., Ltd. All Rights Reserved.