BAGGEBO Cabinet Assembly Instructions

Important Safety Information

⚠️ WARNING!

Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.

Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instructions carefully.

Parts List

The following hardware components are included:

8x Screw (Part #100229)
16x Dowel (Part #101345)
1x Screw (Part #119976)
2x Screw (Part #109558)
1x Screw (Part #109041)
1x Screw (Part #101068)
2x Washer (Part #100823)
1x Washer (Part #101313)
1x Bracket (Part #103651)
4x Bracket (Part #122628)
1x Knob/Cap (Part #10062514)
1x Shelf Support (Part #133127)
1x Shelf Support (Part #139477)
2x Shelf Support (Part #10119658)
2x Shelf Support (Part #10119600)
1x Drawer Component (Part #105493)
1x Allen Key (Part #100006)
1x bag Nails (Part #319503)
1x Bracket (Part #106989)

Main furniture components (panels, doors, shelves) are assembled according to the steps below.

Assembly Steps

Step 1

Place the base panel on a soft surface to prevent scratches. Attach the bracket (1x Part #103651) to the panel using two screws (2x Part #109558). [Diagram shows a hand turning a screw with a screwdriver, and a close-up of the bracket being attached to a panel with two screws. A 'no' symbol with a hand touching the panel is shown, indicating to avoid touching the surface directly.]

Step 2

Insert four dowels (4x Part #101345) into the designated holes on one of the side panels. [Diagram shows a close-up of dowels being inserted into holes on a panel edge.]

Step 3

Connect the bottom panel to the side panel by aligning the dowels and securing with screws. [Diagram shows a side panel being connected to a bottom panel, with dowels aligning and screws being inserted.]

Step 4

Attach the second side panel by inserting four dowels (4x Part #101345) and securing with screws. [Diagram shows the second side panel being attached to the bottom panel, using dowels and screws.]

Step 5

Connect the middle shelf panel. Insert four dowels (4x Part #101345) into the side panels and secure the middle shelf with four screws (4x Part #100229) using the Allen key (1x Part #100006). [Diagram shows the middle shelf being inserted and secured with screws and dowels.]

Step 6

Insert two dowels (2x Part #101345) into the top edges of the side panels. [Diagram shows dowels being inserted into the top of the side panels.]

Step 7

Attach the top panel. Insert six dowels (6x Part #101345) into the top panel and secure it to the side panels. [Diagram shows the top panel being attached, with dowels and screws.]

Step 8

Secure the top panel further by inserting four screws (4x Part #100229) from the inside. [Diagram shows screws being inserted from the inside to secure the top panel.]

Step 9

Assemble the drawer. Place the drawer base panel on a flat surface. Attach the drawer sides and back using fourteen nails (14x Part #101221) and the drawer component (1x Part #105494). Use a hammer. [Diagram shows a drawer box being assembled with nails and a specific component, using a hammer. A warning symbol is shown next to a diagram indicating incorrect placement of a nail.]

Step 10

Attach the drawer runners/guides to the cabinet frame. Use four brackets (4x Part #122628) and a hammer. [Diagram shows brackets being hammered into place on the inside of the cabinet frame.]

Step 11

Attach the wall mounting bracket to the top back of the cabinet. Use one screw (1x Part #109041) and one washer (1x Part #100823). [Diagram shows the wall bracket being attached to the cabinet with a screw and washer, using a screwdriver. Two views of the bracket attachment are shown, one correct, one incorrect with a cross mark.]

Step 12

Prepare the wall for mounting. Position the cabinet against the wall and mark the hole locations for the wall bracket. Secure the cabinet to the wall using the wall mounting bracket (1x Part #100823) and appropriate wall fixings (not included). [Diagram shows the wall bracket being adjusted and secured to the wall, with arrows indicating adjustment. The cabinet is shown against the wall.]

Step 13

Insert two shelf supports (2x Part #10119600) into the desired shelf positions inside the cabinet. [Diagram shows shelf supports being inserted into holes inside the cabinet.]

Step 14

Insert two shelf supports (2x Part #10119658) into the desired shelf positions inside the cabinet. [Diagram shows more shelf supports being inserted.]

Step 15

Attach the top back panel. Use one screw (1x Part #101068) and one washer (1x Part #101313). [Diagram shows the top back panel being attached with a screw and washer.]

Step 16

Attach the doors. Insert one shelf support (1x Part #139477) into the bottom of the door hinge mechanism. Insert another shelf support (1x Part #133127) into the top of the door hinge mechanism. [Diagram shows two types of shelf supports being inserted into the door hinge components.]

Step 17

Mount the doors onto the cabinet. Align the hinge mechanisms with the pre-drilled holes on the cabinet frame and push the door into place. [Diagram shows a door being attached to the cabinet, with an arrow indicating the motion.]

Step 18

Secure the doors. Push the hinge mechanism until it clicks into place. [Diagram shows a close-up of the hinge mechanism clicking into place.]

Step 19

Attach the door knobs. Insert one knob (1x Part #10062514) and secure it with one screw (1x Part #119976). [Diagram shows a door knob being attached to the door with a screw.]

ℹ️ The final assembled product is a cabinet with two doors and adjustable shelves.

	IKEA BAGGEBO Storage Cabinet Assembly Instructions Step-by-step guide to assembling the IKEA BAGGEBO storage cabinet, including parts list, safety warnings, and detailed instructions for a secure and correct build.
	BAGGEBO Storage Unit Assembly Instructions \| IKEA Step-by-step assembly guide for the IKEA BAGGEBO storage unit. Learn how to build and safely install your new furniture, including crucial wall-mounting instructions to prevent tip-over accidents. This manual provides detailed instructions and part identification for a smooth assembly process.
	EKET Storage Unit Assembly Instructions Comprehensive assembly guide for the IKEA EKET storage unit, detailing all steps from unboxing to final installation, including crucial safety warnings about furniture tip-over and wall anchoring. This document provides clear, step-by-step instructions with textual descriptions of diagrams.
	EKET Cabinet Assembly Instructions - IKEA Step-by-step guide for assembling the IKEA EKET cabinet. Includes safety warnings, parts list, and detailed instructions for building your EKET furniture.
	BAGGEBO Cabinet Assembly Instructions Step-by-step assembly guide for the IKEA BAGGEBO cabinet, including safety warnings, parts list, and instructions for wall attachment to prevent tip-over accidents.
	IKEA BAGGEBO Cabinet with Door Assembly Instructions Comprehensive guide for assembling the IKEA BAGGEBO cabinet with door, featuring step-by-step instructions, safety warnings, and a parts list. Includes details on attaching doors, handles, and anti-tip hardware.
	BILLY Bookcase Unit Assembly Instructions Comprehensive assembly guide for the IKEA BILLY bookcase unit, featuring step-by-step instructions, safety warnings, and a detailed parts list. Ensure furniture is securely attached to the wall to prevent tipping.
	TROFAST Storage System Assembly Instructions Step-by-step assembly guide for the IKEA TROFAST storage system, detailing how to build the frame and attach components safely. Includes warnings and a parts list.