BAGGEBO Storage Cabinet
Important Safety Information ⚠️
WARNING!
Furniture can tip over, causing serious or fatal crushing injuries. To prevent tipping, this furniture must be used with the wall attachment device(s) included.
Wall mounting screws and wall plugs are not included. Use screws and plugs suitable for your walls. If you are unsure, seek professional advice. Read and follow each step of the instructions carefully.
This warning is provided in multiple languages: Spanish, Catalan, Basque, and Galician.
Tools Required ?
The following tools are typically needed for assembly:
- Screwdriver (Phillips head) ?
- Hammer ?
- Allen key (included, part 100006)
Diagrams show a person gesturing with tools, a person looking confused at parts, a person at an IKEA store, and a person trapped under furniture with a warning symbol ⚠️.
Parts List
| Part Description | Part Number | Quantity |
|---|---|---|
| Long Screw | 100229 | 8x |
| Wooden Dowel | 101345 | 16x |
| Screw | 119976 | 1x |
| Screw | 109558 | 2x |
| Screw | 109041 | 1x |
| Screw | 101068 | 1x |
| Washer | 100823 | 2x |
| Screw | 101313 | 1x |
| Drawer Runner Part | 103651 | 1x |
| Drawer Runner Part | 122628 | 4x |
| Plastic Cap/Foot | 10062514 | 1x |
| Drawer Runner Part | 133127 | 1x |
| Drawer Runner Part | 139477 | 1x |
| Hinge Arm | 10119658 | 2x |
| Hinge Cup | 10119600 | 2x |
| Plastic Insert/Holder | 105493 | 1x |
| Nails | 319503 | 1x bag |
| Wall Mounting Bracket | 106989 | 1x |
Assembly Instructions
Step 1
Attach part 103651 to the base panel using two screws (109558). Ensure correct orientation as shown; incorrect orientation is crossed out ❌.
Diagram shows a base panel on a rug, with part 103651 being screwed into place. Close-up shows correct and incorrect placement.
Step 2
Insert four wooden dowels (101345) into the designated holes on the side panels.
Diagram shows wooden dowels (101345) being inserted into holes on side panels.
Step 3
Connect the side panels to the shelf panel, aligning the dowels with the corresponding holes.
Diagram shows side panels and a shelf panel being joined using the inserted dowels.
Step 4
Attach the remaining side panels using four wooden dowels (101345) for each.
Diagram shows the frame structure being built with additional side panels and dowels.
Step 5
Secure the assembled frame using four long screws (100229), driven in with the tool 100006 (Allen key).
Diagram shows the frame being secured with long screws (100229) using the Allen key (100006).
Step 6
Insert two wooden dowels (101345) into the top panel.
Diagram shows two wooden dowels (101345) being inserted into the top panel.
Step 7
Attach the top panel to the frame, aligning it with the six wooden dowels (101345).
Diagram shows the top panel being attached to the main frame.
Step 8
Secure the frame by inserting four long screws (100229).
Diagram shows the frame being further secured with long screws (100229).
Step 9
Assemble the drawer component. Insert part 105494 into the base. Secure it using 14 nails (101221) with a hammer ?. Ensure proper alignment and avoid over-hammering ⚠️.
Diagram shows a drawer base being assembled by hammering nails (101221) into part 105494. Safety notes about correct hammering are displayed.
Step 10
Attach four drawer runners (122628) to the inside of the cabinet frame using a hammer ?.
Diagram shows four drawer runner parts (122628) being attached to the interior sides of the cabinet frame.
Step 11
Attach the wall mounting bracket (106989) to the top of the cabinet using a washer (100823) and screw (109041). Ensure correct attachment as shown; incorrect attachment is crossed out ❌.
Diagram shows the wall mounting bracket (106989) being attached to the top rear of the cabinet, with a close-up of the screw (109041) and washer (100823). Correct and incorrect mounting are illustrated.
Step 12
Attach the wall mounting bracket to the wall. Use screw (100823) and appropriate wall anchors (not included). The diagram shows adjusting the bracket for a secure fit ↔️.
Diagram shows the wall mounting bracket being secured to a wall. Arrows indicate adjustment for a secure fit.
Step 13
Insert two hinge cups (10119600) into the pre-drilled holes on the doors.
Diagram shows two hinge cups (10119600) being inserted into the doors.
Step 14
Attach two hinge arms (10119658) to the inside of the cabinet frame.
Diagram shows two hinge arms (10119658) being attached to the cabinet frame.
Step 15
Attach a panel (likely a shelf support or back panel element) using one screw (101068) and washer (101313).
Diagram shows a panel being attached with screw (101068) and washer (101313).
Step 16
Attach the door hinges. Insert part 139477 into the door and part 133127 into the cabinet frame, then connect them.
Diagram shows parts 139477 and 133127 being used to connect the door to the cabinet via the hinges.
Step 17
Attach the door to the cabinet by aligning the hinge components. A bracket is shown being used to guide the attachment.
Diagram shows the door being swung into place and attached to the cabinet hinges.
Step 18
Secure the door hinges. Tighten the screws to ensure the door is firmly attached. A "Click!" sound indicates proper engagement.
Diagram shows the hinge screws being tightened, with a close-up indicating a 'Click!' sound upon secure attachment.
Step 19
Attach the door handle. Use handle part 10062514 and screw 119976. Tighten the screw ?.
Diagram shows the door handle (10062514) being attached to the door using screw (119976).
Final Product
The assembly is now complete. You have successfully built the BAGGEBO storage cabinet.
Diagram shows the completed cabinet with doors open, revealing shelves. An information icon ⓘ is displayed.
ⓘ Product Information
The BAGGEBO storage cabinet features adjustable shelves and doors. Ensure it is securely attached to the wall for safety.
