KTC H24S17 LCD Monitor Display User Guide
Version 2.0
Product Introduction
This is a high-performance intelligent multiple frequency scanning display that utilizes an active matrix thin film transistor LED-backlit LCD. The display is controlled via microcomputer MCU digital technology. It is compact and lightweight, making it suitable for narrow working spaces.
Package Contents
Before installation, please verify that the following items are included in the packing box:
- LCD x1
- Signal Cable x1
- Power Adapter x1
- Warranty Card x1
- Base and mounting screw (M4x16)
- Screwdriver x1
- User Guide x1
If any of these items are missing, please contact your product distributor immediately. Specific accessories may vary; please refer to the actual product. Retain packing materials for future transport.
Base Installation
Install the base onto the stand and secure it with one M4x16 screw.
Keys and Interfaces
Monitor Controls:
- Joystick: Navigate menus and settings.
- Power Indicator: Displays the power status of the monitor.
Initial Shortcut Keys:
- ↑: Signal Source Input
- ↓: Luminance
- Shortcut Key for Gaming Assistance
- Shortcut Key for Preset
Power Button: Short-press to turn on the display. Press and hold for 3 seconds to turn off the display.
Interface Ports:
- DC Power Input
- HDMI 1
- HDMI 2
- DP (DisplayPort)
Signal Cable Connection: Connect the signal cable to the HDMI or DP output port on your PC and then to the corresponding input port on the LCD monitor.
Headset Connection: Connecting a headset enables audio output and supports external loudspeakers.
Power Indicator Status
- Blue Indicator: Proper functioning of the display.
- Flashing Red Indicator: No signal detected.
The display will function normally if a signal is provided again in energy conservation state. The display remains powered on in standby mode. Unplug the power cord when not in use for safety.
Screen Tilt Adjustment
The bracket allows for tilting the screen up and down within a range of -5° to 15°.
Mounting Location and Ventilation
Ensure adequate ventilation around the display. Maintain at least 10cm of space on all sides and 30cm above the display. Do not cover ventilation holes or insert objects into the shell. Avoid placing the display in confined spaces like book cabinets or built-in closets without proper ventilation. Wall mounting requires a 100mm x 100mm pitch.
Product Technical Specifications
- Panel Dimension: 23.6"
- Best Operating Resolution Ratio: 1920x1080@165Hz
- Input Voltage: DC 12V/3A
- Contrast: 3000:1 (TYP)
- Visible Area: 521.3952x293.2848mm
- Pitch size for wall mount: 100mm x 100mm
Working Environment Requirements
- Maximum altitude: 2000m
- Atmospheric pressure: 86kPa~106kPa
- Operating temperature and humidity: 0℃~40℃, 30%~90% (Non-condensing)
- Storage temperature and humidity: -20℃~55℃, 20%~93% (Non-condensing)
Installation Guide
- Install the display near an easily accessible AC power socket.
- Use the provided base for safety.
- Place the display on a smooth horizontal plane to prevent injury.
- Avoid placing the display where it may be subjected to mechanical vibration.
- Do not place the display where insects may enter.
- Avoid placing the display directly facing an air conditioner to prevent condensation and potential faults.
- Do not place the display in environments with strong electromagnetic fields, as it may be interfered with or damaged by electromagnetic waves.
Simple Problems Disposal
| Symptom | Disposal Method |
|---|---|
| 1. Blank screen / Power indicator does not work | Check if the power supply is properly connected to the display and the power socket. Ensure the display is turned on. |
| 2. Blurred images (too large or too small) | Go to "Image Settings" and select "Image Auto Adjust" for automatic monitor adjustment (VGA monitors only). |
| 3. Dark screen | Adjust contrast and brightness in the "Brightness & Contrast" menu. |
| 4. Display overheating | Ensure at least 10cm of ventilated space around the display. Do not place objects on the display. |
| 5. Dark/light spots when powered on | This is normal. Uneven light emission from the backlight tube may occur initially due to temperature differences. Normal light emission and elimination of spots should occur within 20 minutes. |
| 6. Image distortion, flashing, shaking | Check your computer's configuration, select the correct resolution, and reset the refresh rate. |
| 7. Noisy signal when powered off | This may be caused by normal discharge during the display's power-off state. |
Safety Protection
If the PC video signal exceeds the display's frequency range, the display will disable line and field synchronizing signals to protect itself. You must set the PC's output frequency to an acceptable range for the display to function correctly.
Power Management System
- Normal Operation: Power Consumption ≤36W
- Standby: Power Consumption ≤0.5W
Important Safety Precautions
- Read all instructions carefully before use.
- Unplug the power cord before cleaning. Wipe with a soft, damp cloth. Use LCD screen cleaner for stubborn stains. Do not use liquid or spray cleaners.
- Do not use unrecommended accessories, as this may cause danger.
- When unplugging the power cord or adapter, hold the plug, not the cord.
- Do not place the display near water sources (bathtubs, sinks, pools). Do not place on wet ground.
- Do not press the LCD screen surface with fingers or hard objects.
- Ventilation holes and slots are for component ventilation and heat dissipation. Do not block them by placing the display on beds, sofas, or carpets. Avoid placing near or above radiators or heaters. Ensure adequate ventilation for embedded installations.
- Use only the specified power supply type. Consult your dealer or local power administration if unsure.
- The three-prong plug requires a properly grounded socket for safety. Contact an electrician to replace the socket if necessary.
- Do not attempt to repair the display yourself. Refer servicing to qualified personnel.
- Unplug the power cord and contact qualified personnel for repair if: the power cord or plug is damaged, the display is dropped or the shell is damaged, or any obvious abnormality indicates a need for repair.
- Place the display in a well-ventilated environment, away from strong light, high temperature, and humidity.
- Store the display within a temperature range of -20°C to 55°C to prevent permanent damage.
- The monitor screen is fragile; handle with care during movement or handling.
Product Information
Model: KTC H24S17
More Information: Scan the QR code or visit EN.KTCPLAY.COM for more details.
Contact: support@ktcplay.com, support.eu@ktcplay.com [Europe]
Recycling Information: Please send waste electrical and electronic products to a qualified manufacturer for recycling according to national laws and regulations.
HDMI™: The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Product Warranty Card
Customer Name:
Tel:
Address:
Model:
Device Number:
Purchase Date:
Warranty Rules:
- Three-year free warranty from the date of purchase or as agreed in the contract.
- Warranty does not cover failures or damages caused by artificial or natural disasters, improper operation, or user disassembly.
- The warranty is limited to product maintenance and does not cover other liabilities.
- For warranty policy after the warranty period, visit EN.KTCPLAY.COM.
Product Certification: CHECKER: OC PASS
Notice: Please fill out and return the card when applying for warranty.
