SaunaLife Garden Series Model G4 Outdoor Sauna
Assembly Manual - April 2023
Introduction
Read the entire manual before assembly. Get the tools you need.
Parts List
| Pos / Part ID | Description / Specification | Quantity | Profile (mm) | Length (mm) | Notes |
|---|---|---|---|---|---|
| 001 | Wood Plank | 1 | 45x130 | 1147 | |
| 002 | Wood Plank | 1 | 45x130 | 338 | |
| 003 | Wood Plank | 14 | 45x130 | 1147 | |
| 004 | Wood Plank | 14 | 45x130 | 338 | |
| 005 | Wood Plank | 2 | 45x130 | 2475 | |
| 006 | Wood Plank | 2 | 45x130 | 2475 | |
| 007 | Wood Plank | 2 | 45x58 | 459 | |
| 008 | Wood Plank | 2 | 45x130 | 1545 | |
| 009 | Wood Plank | 2 | 45x129 | 1011 | |
| 010 | Wood Plank | 1 | 45x130 | 2260 | |
| 011 | Wood Plank | 30 | 45x130 | 2260 | |
| 012 | Wood Plank | 2 | 45x65 | 338 | |
| 013 | Wood Plank | 28 | 45x130 | 338 | |
| 014 | Wood Plank | 1 | 45x130 | 2260 | |
| 015 | Wood Plank | 2 | 45x130 | 2490 | |
| 016 | Wood Plank | 1 | 45x65 | 2260 | |
| 017 | Wood Plank | 1 | 45x130 | 2260 | |
| GR1 | Groundframe | 2 | 90x45 | 2380 | |
| FB1 | Floorbeams | 2 | 45x45 | 2070 | |
| FB2 | Floorbeams | 1 | 45x45 | 1890 | |
| FB3 | Floorbeams | 3 | 45x45 | 1990 | |
| FB4 | Floorbeams | 3 | 45x45 | 345 | |
| PR1 | Purlins | 1 | 70x170 | 2490 | |
| RB1 | Roof Boards | 7.3m² | 20 | 2913 | (1341mm + 1572 mm) |
| R1 | Frontboard | 2 | 20x140 | 2530 | |
| R2 | Gableboard | 4 | 20x140 | 1550 | |
| R3 | Frontboard Fixing | 2 | 45x45 | 2490 | |
| SK | Hammer Block | 2 | 45x65 | ||
| DR1 | Door Frame Component | 1 | 800x1900 | ||
| WN1 | Window Frame Component | 1 | 765x1900 | ||
| WN2 | Window Frame Component | 1 | 765x1900 | ||
| P1 | Floor Strips | 9m | 20x40 | ||
| P2 | Slats (Door/Window) | 6+6 | 20x90 | 1880 | INT, EXT SLATS DR1, WN1, WN2 |
| P3 | Slats (Door/Window) | 1+1 | 20x90 | 1065 | INT, EXT SLATS WN2 |
| F1 | Floor/Terrace Board | 4m² | 28 | 1995 | Lagerholz |
| F2 | Terrace Floor Board | 0.84m² | 28 | 2090 |
Wood Quantities Summary
- Groundframe: 20
- First row of wall logs: 12
- Floorboards: 130
- Floor edge trims: 15
- Roofboards: 95
- Frontboard, Gableboard, Frontboard fixing: 50
- Purlins: 2
- Window and door slats: 80
Assembly Instructions
Step 1: Groundframe
Fasten the base frame with screws. If possible, fasten the base frame to the Foundation. Diagonals must be of the same lengths. Drill holes before screws.
Tools needed: Water level and measuring tape.
Diagram Description: A diagram showing the assembly of the ground frame. It depicts base beams (GR1, FB1, FB2, FB3, FB4) forming a rectangular base, with diagonal bracing. A spirit level and measuring tape are shown.
Step 2: First Wall Row
The wall plank must be 10 mm above the edge of the base frame. The first wall plank row must be fixed with screws to the base frame.
Diagram Description: A diagram showing the first row of wall planks being attached to the ground frame. A drill is shown fastening a plank.
Step 3: Installing Walls
Use hammer and hammer block.
Diagram Description: A diagram showing the initial wall construction with corner posts and wall planks. A hammer and hammer block are illustrated.
Step 4: Installing Walls (Continued)
Use hammer and hammer block. Install the positions below completely.
Diagram Description: Diagrams showing the progression of wall assembly, adding more rows of planks.
Step 5: Installing Walls / Purlins
Use hammer and hammer block.
Diagram Description: Diagrams showing the installation of wall planks and the first purlins.
Step 6: Purlins
Use hammer and hammer block.
Fasten the purlins with screws. Make sure the upper side of the purlins is oblate. If necessary, adjust the tapping of the purlins. Fasten the gable parts with screws.
Diagram Description: Diagrams illustrating the attachment of purlins to the top of the walls. A close-up shows screw fastening.
Step 7: Ventilation Grill / Roof Boards
Install the ventilation grill in the back wall.
Fasten the roof boards with screws. Start with the groove edge on the board.
Diagram Description: Diagrams showing the installation of a ventilation grill and the start of roof board installation. A close-up shows a drill fastening a roof board.
Step 8: Roof Boards
Complete the installation of parts RB1. Cut the last roof board to the correct width. The edge must be aligned with the wall plank and the purlins.
Diagram Description: Diagrams showing the completion of roof board installation, including cutting the final board. A close-up shows a circular saw.
Step 9: Roof Boards (Frontboards)
Cut correct lengths and fasten frontboards fixing with screws.
Diagram Description: Diagrams showing the attachment of frontboards using a saw and screws.
Step 10: Roof Cover / Covering Strips
Install roof shingles, use small nails. Fasten the frontboard with screws. Cut the correct angle and fasten gableboards with screws.
Diagram Description: Diagrams showing the installation of roof shingles and covering strips. Close-ups show screw fastening.
Step 11: Floor / Terrace Boards / Floor Stripes
Fasten the floor / terrace boards with screws. Cut the final floor/ terrace board to the correct width.
Cut the floor stripes on right angle and size, then install with screws.
Diagram Description: Diagrams showing the installation of floor/terrace boards and floor stripes. Close-ups show screw fastening and cutting floor stripes.
Step 12: Door / Window
Slats can only be screwed to the door and window frame and not to the wall.
Diagram Description: Diagrams illustrating the assembly of door and window frames with slats.
Step 13: Door / Window (Installation & Adjustment)
To fix the door and windows to the house use only slats. Slats can only be screwed to the door and window frame and not to the wall.
Adjust the door. (Indications for Left/Right, Up/Down, In/Out adjustments are shown).
Diagram Description: Diagrams showing the final placement of doors and windows, and an illustration for adjusting the door, indicating adjustment directions.
Bench Assembly (Optional/Accessory)
Bench Parts List
| Part | Quantity |
|---|---|
| Element 1 | 1 |
| Element 2 | 1 |
| Element 3 | 2 |
| Det 1 | 3 |
| Det 2 | 2 |
| Det 3 | 2 |
| Det 4 | 1 |
| Det 5 | 2 |
Bench Assembly Instructions
Note: Drill the pilot holes for the screws.
Assemble the bench components using the specified screws:
- Use 25mm screws for connecting Element 3 with Det 1.
- Use 70mm screws for connecting other parts of the bench structure.
- Use 40mm screws for specific connections (e.g., with Det 4).
Diagram Description: Diagrams show the assembly of bench components, indicating screw placement, dimensions, and the overall structure.
