SaunaLife Cube Luxury Series CL3G Outdoor Sauna
Dimensions: 52"D x 54"W x 82"H
Note: Please read manual before construction.
Tools Needed
- Measuring tape
- Marker pen
- Circular saw
- Water level ?️
- Hammer ?
- Drill ड्रिल
- Crescent wrench ?
- Utility knife ?
- Rubber mallet ?
- Screwdriver ?
- Extra hands ?
Parts List
The following components are included:
- DET 1 (x2) - Dimensions: 51.18" x 7" x 2.68"
- DET 2 (x1) - Dimensions: 51.18" x 4.33" x 1.65"
- DET 3 (x55) - Dimensions: 51.18" x 4.17" x 1.65"
- DET 6 (x2) - Dimensions: 51.18" x 2.32" x 1.65"
- DET 6c/d/e/f (x1) - Dimensions: 51.18" x X" x 1.65" (with various width options: 1", 3/8", 3/4", 1 3/16")
- DET Sa (x1) - Dimensions: 76.14" x 13.54" x 1.07"
- DET Sb (x1) - Dimensions: 76.14" x 13.54" x 1.07"
- DET Ta (x1) - Dimensions: 24" x 6" x 1.1"
- DET Tb (x1) - Dimensions: 24" x 3.54" x 1.1"
- DET Y (x1) - Dimensions: 51.1" x 76.89" x 1.1"
- DET U1 (x1) - Dimensions: 49.02" x 3.54" x 0.71"
- DET U2 (x2) - Dimensions: 73.23" x 3.54" x 0.71"
- DET 10a (x3) - Dimensions: 17.72" x 1.73" x 1.73"
- DET 10c (x2) - Dimensions: 5.24" x 1.73" x 1.73"
- DET 11a (x2) - Dimensions: 32" x 1.73" x 1.73"
- DET 11b (x1) - Dimensions: 32" x 1.73" x 1.73"
- DET 11c (x2) - Dimensions: 9.84" x 1.73" x 1.73"
- DET 10 (x1) - Dimensions: 49.21" x 20.47" x 2.83"
- DET 12 (x1) - Dimensions: 22.83" x 11.81" x 2.83"
- DET 11 (x1) - Dimensions: 30.71" x 8.07" x 2.83"
- DET 14 (x1) - Dimensions: 48.03" x 7.48" x 2.2"
- DET 21 (x1) - Part Number: D590/1690PR8 - Dimensions: 66.54" x 23.23"
- DET 21c (x2) - Dimensions: 66.54" x 1.1" x 1.1"
- DET 21d (x2) - Dimensions: 25.43" x 1.1" x 1.1"
- DET 21a (x2) - Dimensions: 65.75" x 1.73" x 0.71"
- DET 21b (x2) - Dimensions: 26" x 1.73" x 0.71"
- DET 22 (x2) - Dimensions: 51.18" x 1.73" x 1.73"
- DET 25a (x16) - Length: 11.22"
- DET 25b (x4) - Dimensions: 51.5" x 4.33" x 0.71"
- DET 25c (x4) - Dimensions: 27.2" x 4.33" x 0.71"
- Underlay felt (1 roll) - Dimensions: 122" x 59"
- DET N (x6) - Part Name: KAT-HAR-MUST
- DET O (x37) - Part Name: KAT-SIN-MUST
- DET V (x4) - Part Name: KI-VIN-25/40/40-ZN - Dimensions: 1.58" x 1.58" x 1"
- DET W (x1) - Part Name: TRAPP (includes W1, W2, W3, W4)
- DET A2 (x2)
- DET G (x1) - Part Name: MU-VENT-PU
- DET F (x3) - Part Name: MU-VENT-ZN-MUS
- Hardware Kit (includes Bit PH2, Torx bits T10, T15, T20, T25, various screws M, Q, H, J, K, L, I, D, E)
Installation Steps
- Step 1: Base Assembly
Place DET 1 on a flat, level surface. Use a water level ?️ to ensure accuracy. Secure with 4x M screws. Attach 2x DET 3 and 1x DET W. Ensure diagonal measurements are equal. A close-up view shows the top view of the assembly.
- Step 2: Attaching Slats
Use a rubber mallet ? to gently tap DET 3 into place. Align grooves on the same line. Secure the structure with 20x M screws. Remove and use these screws for further assembly.
- Step 3: Front Glass-Wall Assembly
Assemble the front glass wall components (Sa, Sb, Ta, Tb). Ensure parts are placed inside up. Use 4x DET V and 16x J screws for attachment. Pay close attention to the indicated measurements (min. 1" and min. 0.85") and be extra careful not to hit the glass.
- Step 4: Wooden Back Wall Assembly
Assemble the wooden back wall using DET Y and DET U2 components. Use a rubber mallet ? for gentle fitting and 12x I screws for securing. The assembly involves parts labeled Y1, Y2, Y3.
- Step 5: Attaching Walls to Base
Use a water level ?️ to ensure walls are plumb. Make sure markings on the wall are centered. Attach DET U1 inside the structure using 2x I screws.
- Step 6: Securing Walls
Use a water level ?️ to ensure walls are plumb. Make sure markings on the wall are centered. Temporarily fix DET 3 to support the walls. Attach DET U2 inside. Secure with 4x I and 2x I screws.
- Step 7: Installing Slats and Removing Supports
Use a rubber mallet ? to gently tap slats into place. Remove DET 3 supports from their temporary positions and use them in the next step. Fasten screws at a slight angle. A close-up view shows the gap between slats.
- Step 8: Joining Slats and Trimming
Join boards together to bridge the gap (labeled 'A'), ensuring they are approximately 1/4" wider than the gap. If necessary, trim the flat edge of the board to create the desired width. Use the appropriate length screws and pre-drill holes (Ø 5/32"). Raise the board slightly before installing and use a rubber mallet ?.
- Step 9: Attaching Outer Panels and Vents
Attach 2x DET A to the exterior. Tighten all nuts securely. Remove any temporary brackets. Install the upper vent using 1x DET G and 3x K screws. Install the lower vent using 3x DET F and 3x K screws. Use 6x K screws for the lower vent assembly.
- Step 10: Installing Interior Supports
Use a water level ?️ for accurate installation. Attach 3x DET 10a and 2x DET 10c to the interior walls, pre-drilling holes (5/32"). Use 2x H and 11x M screws for DET 10a, and 2x H and 2x M screws for DET 10c. Side and front views illustrate placement and measurements (1.57", 0.87", 17.91", 14.96", 32").
- Step 11: Installing Interior Components
Attach DET 12 and DET 10 using appropriate screws (M, H) and pre-drilling. Install DET 11a and DET 11b, ensuring correct alignment and using pre-drilled holes. Front view diagrams show precise placement and measurements (22.52", 15.67").
- Step 12: Installing Door and Side Panels
Install DET 11 and DET 11c, using pre-drilled holes and screws. Attach DET 14. Ensure the door opens outwards; if the handle needs to be on the opposite side, rotate the door 180 degrees. Attach DET 21c, DET 21d, and DET 21 using Q screws. Pre-drill holes as indicated.
- Step 13: Attaching Final Exterior Panels
Attach DET 21a and DET 21b to the exterior. Use a level ?️ and pre-drill holes. Secure with J screws. Attach DET 22 using H screws. Ensure correct alignment and spacing, as shown in the diagrams.
- Step 14: Underlay Felt Installation
Roll out the underlay felt. Fold approximately 2" over the edge. Clamp the end to the edge and cut off any excess parts that extend over the edge.
- Step 15: Shingle Installation
Refer to the shingle installation manual provided in the package. Attach DET N and DET O components, ensuring shingles overlap on top. Cut and use the remaining parts on the opposite side. Refract DET N into three pieces as shown.
- Step 16: Final Exterior Cladding
Attach DET 25c, DET 25b, and DET 25a panels to the exterior. Start from the bottom. Use Q screws and pre-drill holes. Pay attention to the instruction to leave a gap between boards.
General Installation and Maintenance
Important Notes
Identification number of the Product / Serial Number: 123456789. This serial number must accompany any product identification.
General Installation Guidelines
- Careful handling: Treat all wooden parts with care during assembly to avoid scratches or friction.
- Level foundation: Ensure the sauna sits on a stable, level foundation for proper door and window operation. The base must have enough stability to support the sauna.
- Proper drainage: Avoid constant water exposure to wooden materials.
- Electrical and plumbing: Hire qualified professionals for electrical work, including heater and lighting installation.
- Wood treatment: It is recommended to treat all wooden parts after assembly.
Door and Window Maintenance
- Regular checks: Regularly inspect window and door hinges and locks. Tighten loose components and lubricate as needed.
- DOOR ADJUSTMENT INSTRUCTIONS: You will need 3-mm and 5-mm hexagon keys for adjusting the hinges. Remove plastic covers from hinges. Loosen fixing screws (2) one turn (do not remove the glass). If needed, the door can be shimmed up vertically. For left/right adjustment, turn screws (4 & 5) as required, turning one counterclockwise if the other is turned clockwise. Ensure both screws are tight after adjustment.
Wood Protection and Maintenance
- Protective coating: Apply a wood preservative at least once a year (or more often) to improve resistance to dirt and moisture, make cleaning easier, and extend the lifespan of the product.
- Adjusting wick condition: Check and adjust the condition of the sauna's wicks (if applicable) a few times a year.
Sauna Heater and Stones
- Heater and chimney installation: Follow the manufacturer's instructions for heater and chimney installation.
- Cleaning heater stones: Wash new stones before placement to remove dust and chemicals.
- Stone placement: Arrange stones according to the manufacturer's instructions, ensuring heating elements are not exposed.
- First heating: The first heating must take place under supervision for two hours to a temperature of about 210°F. The sauna must be well ventilated during and after heating to allow the wood to absorb finishing materials and form a protective layer.
Sauna Use
- Firewood: Use dry firewood up to 12" long for wood-burning heaters.
- Steam throwing: Throw water only on the heater, not on walls or benches.
- Swimwear: Avoid wearing swimwear in the sauna to prevent damage to the benches from dripping water.
- Seating comfort: Consider using seating pads for increased comfort on hot benches.
- Cracked stones: Check the heater stones regularly, as they can crack over time. Replace or add stones as needed.
Sauna Cleaning After Each Use
- Wipe down benches: Use a clean, damp cloth to wipe down the benches. Do not use running water to clean the bench or other wooden surfaces.
- Cleaning products: Use suitable cleaning products specifically designed for sauna benches and other wooden parts.
- Drying and ventilation: After cleaning, allow surfaces to dry completely and ensure proper ventilation. Run the heater for at least 30 minutes with the vent open and door/windows closed.
Sauna Maintenance - Yearly
- Wood treatment: Re-treat wooden surfaces with a suitable product, especially for frequently used saunas.
- Cleaning surfaces: Clean all surfaces with a soft brush/cloth and a designated cleaning agent according to the product's instructions.
- Heavy stains: For stubborn stains, lightly sand the area before re-treating with wood preservative.
What to Avoid in Your Sauna
- Unsuitable products: Avoid paints, varnishes, harsh disinfectants, or pressure washers, as these can damage the wood.
- Hardware checks: Inspect bench and support mountings. Tighten loose screws if necessary, as wood can loosen due to heat and moisture fluctuations.
- Drying textiles: Avoid drying textiles in the sauna due to fire hazards and potential wood damage from excessive moisture.
- Excessive heat: Do not exceed the maximum temperature specified by the heater manufacturer to prevent fire hazards and wood warping.
- Cleaning methods: Avoid using pressure washers or excessive running water, as this can permanently damage the wood structure.
Wood Characteristics in Saunas
- Natural changes: Wood is a natural material that may crack or warp slightly due to temperature fluctuations. This is normal in saunas with extreme temperature and humidity changes.
- Deformation factors: The risk of wood deformation depends on the material, usage intensity, and is more noticeable with wider boards.
- Darkening wood: Wood in areas exposed to hot steam may darken over time.
- Wood Smell: Thermally treated wood has a characteristic smell that diminishes over time but does not completely disappear. In a sauna, the smell weakens faster if it is heated for a long time and aired at the same time. The smell is softened by treating the wood with a suitable wood oil or wood care product. Do not wash untreated thermal wood with water, as this will make the smell stronger.
