Tuya 4G Solar Camera APP Quick Start Guide

1. Packing List

• Camera
• Solar panel
• Bracket
• Certificate of conformity
• Accessory package
• Manual

2. Schematic Diagram of Interface Description

Diagram showing the camera's components:

• Solar panel
• Antenna
• Speaker
• Photoresistance Lens
• PIR Sensor
• Microphone
• Solar panel interface
• White light indicator LED
• ON/OFF button
• Reset button
• SD Card slot
• SIM Card slot
• USB interface

3. Download and Install the APP

Scan the QR code below and click to install or open the mobile app market to search for Tuya Smart.

4. Sign Up for Login Account

• Enter your mobile phone number or email address.
• Enter the verification code and set the password, then click login.

App Usage: Adding Device

• Open the Tuya Smart APP.
• Click on "Add" (typically a '+' icon).
• Click "Scan Code".

Screenshot showing the 'Welcome Home' screen of the Tuya app with options to add devices.

5. Device Connection

Note: This device has a built-in battery pack. For the first use, please use the DC 5V/2A USB cable to charge for 10 hours.

1. Button Functions:

• Solar panel On/Off button: When close to the USB port, power stops; otherwise, it supplies power.
• On/Off button: Long press for 3 seconds to turn the device on or off.
• Reset button: In the boot state, long press for 5 seconds to reset.

2. Indicator Light:

• Red light flashing ?: Failed to connect to network.
• Blue light solid ?: Enter normal working state after successful registration.
• Blue light flashing ?: Connected to the network successfully.

Connection Steps:

• Scan the QR code on the device.
• Insert the SIM card into the device (the cutaway of the SIM card should be facing down and the chip facing the button).
• If recording is needed, please insert the SD card (the chip of the SD card should be facing the USB interface). Then wait for the red light to turn blue and keep flashing.

Screenshot showing the 'Adding device...' progress screen.

Status: 'Successfully added' (The blue light is on ✔️).

6. Equipment Instructions

PTZ Control

Click the directional arrows [Up] [Down] [Left] [Right] to control the vertical and horizontal rotation of the camera.

Playback

Click "Playback" ▶️, then select the date to view all files and videos for that day.

Support Binding Third-Party Software

Supports binding with Alexa & Google to wake the device up. Click on 'Message Notification' to view the device's alarm messages.

• Alexa
• Google Assistant
• SmartThings

4. Reminders about the PIR Humanoid Detection Feature

The humanoid detection sensitivity can be set in the device settings. When used in a crowded environment, it is recommended to turn off or set the device to low sensitivity to avoid unnecessary wake-ups, thereby prolonging battery service time.

• Off: The device will not perform humanoid induction detection.
• Low: When the device is in hibernation state, it can sense movement detection within 5 meters and trigger a report.
• Middle: When the device is in hibernation state, it can sense movement detection within 7 meters and trigger a report.
• High: When the device is in hibernation state, it can sense movement detection within 10 meters and trigger a report.

7. Matters Needing Attention

PIR sensor is sensitive to cold and hot disturbances. Points to note during installation:

• Avoid placing the device in areas with air currents (e.g., air conditioning outlets, equipment cooling outlets, near fans, or curtains).
• Do not install the device directly in front of glass or mirrors.
• The recommended installation height is approximately 2.5m - 3m.
• Do not invert the device.

The device supports battery power, and its service time is affected by wake-up time and frequency. Therefore, it is suggested to turn off the human detection function or set it to low sensitivity in crowded environments to reduce wake-up times and extend application time. When the device is low on power, please charge it promptly. Prolonged underpowering may cause battery failure.

During installation, ensure a stable 4G network signal at the location, especially in remote mountainous areas. Verify the 4G network signal strength of the operator.

This device is a low-power intelligent product that supports APP remote wake-up, PIR human detection wake-up, and button wake-up. It automatically enters sleep state after a short working period after each wake-up.

To ensure normal operation, first charge the device for 10 hours using the original DC 5V/2A charger and USB cable. Do not use a mobile power supply for charging, as it may cause a short circuit.

8. Problem Resolution

• Add failed:
  • Check if the device's blue light is flashing ?.
  • Ensure the network is normal.
• Offline equipment:
  • Check if the SIM card is connected properly.
  • Check if the device battery is depleted. Try connecting via USB cable for power supply and attempt again.
• Unable to preview:
  • The server may be congested. Please try restarting the APP.
• No message push:
  • Ensure the APP has notification permissions.
  • Ensure the alarm message push switch is enabled in the APP Personal Center Settings.
• No video files:
  • Insert the SD card before starting up.
  • Ensure the device's PIR switch is on.
  • Ensure the device's recording switch is on.
  • Check the SD card status in the APP. If abnormal, try formatting the SD card.

9. Common Problems

Q: Why does the battery drain so fast?

A: Frequent triggering of the human detection function in crowded environments can cause the device to work for extended periods, consuming power rapidly. Try lowering the PIR sensitivity setting. Viewing video playback files for long durations also consumes power. Check if the device signal is stable; unstable networks can cause the device to wake up multiple times, consuming power. Consider changing the device's position or SIM operator.

Q: How can I confirm that the camera is connected properly?

A: Try actively triggering the PIR sensor. Wait for 3 seconds; if the blue light turns on ?, it indicates the device is connected properly.

Manual Specifications

Material: 105g matte paper, accordion fold. Finished folded size: 75x125mm. Finished unfolded size: 300x125mm. Folding effect.