HUANUO Monitor Desk Mount Instruction Manual V3.0

IMPORTANT SAFETY INFORMATION

Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our Technical Support line at 1-800-556-0533 or customer service at support@huanuoav.com.

CAUTION: Avoid potential personal injuries and property damage!

• Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. HUANUO is not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
• The desk must be capable of supporting five times the weight of the monitor and mount combined.

Check the VESA Pattern of Your Monitor before the Installation

VESA Dimensions:

• 75 mm ≈ 3 in
• 100 mm ≈ 4 in
• 200 mm ≈ 7 7/8 in

Minimum VESA pattern: 75mm/3 in (W)x75mm/3 in (H)

If your monitor VESA is greater than 200x200 mm/8x8 in or less than VESA 75x75mm/3x3 in, this mount is NOT compatible.

If this mount is NOT compatible, please contact customer service at support@huanuoav.com to find a compatible mount.

Tools Needed (Not Included)

• Phillips Screwdriver
• Drill (Optional)
• 7/16 in (11mm) - 55/64 in (22mm) Drill (Optional)
• 3/8 in (10mm) Socket Wrench

Supplied Parts and Hardware

Warning: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. If you require replacement parts, please contact our Technical Support line at 1-800-556-0533 or customer service at support@huanuoav.com.

Please note: Not all hardware included in this package will be used.

Supplied Parts and Hardware for Step 1

• Pole [01] (x1)
• C-Clamp Brace [02] (x1)
• Locking Plate [b] (x1)
• Bottom Pad [c] (x1)
• C-Clamp [03] (x1)
• Washer M10 [D1] (x1)
• Nut M10 [D2] (x1)
• Bolt M6X12MM [D3] (x1)
• Bolt M6X8MM [F3] (x2)
• Bolt M8X10MM [E1] (x2)
• Washer M6 [E2] (x1)
• 13/64 in (5mm) Large Allen Key [F1] (x1)
• 5/32 in (4mm) Small Allen Key [F2] (x1)

Supplied Parts and Hardware for Step 2

• Monitor Connector [04] (x1)
• Decorative Cover [a] (x1)

Supplied Parts and Hardware for Step 3

• Faceplate [05] (x1)
• Extender Bracket [06] (x4)
• Bolt [F4] (x4)
• Nut [F5] (x4)

Supplied Hardware for Step 4

• Bolt M4X12MM [A1] (x4)
• Bolt M4X16MM [A2] (x4)
• Bolt M5X15MM [B1] (x4)
• Bolt M6X15MM [B2] (x4)
• Washer M6 [C1] (x4)
• Spacer 5mm [C2] (x8)

Supplied Hardware for Step 5

• Bolt M6X15MM [F] (x1)

Step 1 Install the Base

Option A: C-Clamp Installation

Attach the C-Clamp Brace [02] to the Pole [01] using Bolts [D3] and Small Allen Key [F2]. Then attach the C-Clamp [03] to the C-Clamp Brace [02] using Bolts [F3] and Small Allen Key [F2]. Insert the Locking Plate [b] into the C-Clamp [03]. Secure the Locking Plate [b] with Washer [E2] and Bolt [E1] using the Large Allen Key [F1]. Slide the Bottom Pad [c] onto the C-Clamp [03].

The diagram shows the C-Clamp [03] being attached to the desk, with the Locking Plate [b] inserted and secured. The desk thickness can range from 3/8 in (10mm) to 1 3/16 in (30mm), 1 3/16 in (30mm) to 2 11/64 in (55mm), or 2 11/64 in (55mm) to 3 5/32 in (80mm).

Option B: Grommet Installation

Insert the Grommet parts [03a, 03b] through the desk grommet hole. Attach the Pole [01] to the Grommet parts [03a, 03b] using the Locking Plate [b].

If there is no grommet hole on your desk, position the pole [01] on the mounting surface and mark the hole. Drill a hole using a drill bit in a diameter of 7/16 in - 55/64 in (11-22mm) at the marked position through the mounting surface.

Step 2 Secure Monitor Connector and Decorative Cover to Pole Assembly

Attach the Monitor Connector [04] to the top of the Pole Assembly. Secure it using the Large Allen Key [F1]. A decorative cover [a] is also attached.

Step 3 Choose the Combination that Applies to Your VESA Hole Pattern

Option A: No Need to Attach Extender Brackets [06] to Faceplate [05]

For VESA hole patterns: 3x3 in (75x75mm) and 4x4 in (100x100mm).

Option B: Need to Attach Extender Brackets [06] to Faceplate [05]

For VESA hole patterns: 8x8 in (200x200mm) and 8x4 in (200x100mm). Attach Extender Brackets [06] to the Faceplate [05] using Bolts [F4] and Nuts [F5]. A 3/8 in (10mm) Socket Wrench is needed.

Step 4 Attach Faceplate (or Faceplate with Extender Brackets) to the Back of Monitor

Attach the Faceplate [05] (or Faceplate with Extender Brackets [06]) to the back of the monitor using Bolts [A1/A2/B1/B2] and Washers [C1]. Spacers [C2] may be needed depending on the monitor's back panel. Use a Phillips Screwdriver (not included). Ensure the monitor is oriented UP correctly.

Step 5 Hang the Monitor to the Stand

HEAVY! You may need assistance with this step. Align the monitor's VESA mount with the Monitor Connector [04] on the stand and slide it down to secure. Use the Small Allen Key [F2] to tighten the safety bolt [F].

Step 6 Adjust the Tilt Angle and Manage the Cables

Tilt Adjustment

1. If the monitors can stay at the desired height by itself, no adjustment needed.
2. The tilt angle of the monitor will not be adjusted if the set screw [T] is over-tightened. In this case, you need to turn the set screw [T] in anti-clockwise direction to decrease torque until the monitors can be hovered at any position.
3. The monitors will drop automatically if the set screw [T] is over-loosen. In this case, you need to turn the set screw [T] in clockwise direction to increase torque until the monitors can be hovered at any position.

Warning: To avoid tipping, please be careful not to extend the monitor too far backward. When you adjust the angle of the monitor, please make sure the monitor is balanced to avoid instability of the center of gravity of the base.

Use the provided cable ties (2X Cable tie) to manage cables.